The RCeveryday.com Shop Truck Chassis Kit Full Assembly
Vložit
- čas přidán 19. 02. 2024
- Kits available soon on RCeveryday.com
Offering a base 2wd chassis builders kit to make your own shop truck!
Time stamps! Find the part you need to assemble:
:13 introduction
5:29 overview of the chassis layout
8:25 front IFS bracket install
10:21 Body Mounts
12:54 Servo and servo mount
15:43 Motor and Transmission install
24:36 Rear axle and leaf springs
28:51 Rear suspension install to frame
34:25 Front suspension install
46:25 Front Shocks
47:30 Driveshaft measurement
50:09 Front setup not slammed
53:45 Body install & electronics
56:18 Wrap up
Parts list below:
RCeveryday.com Shop Truck Parts List
-Shop Truck Chassis Kit
RCeveryday.com
-Tamiya TL01 Front suspension parts
www.google.com/search?q=tamiy...
-SSD scale engine
www.amainhobbies.com/ssd-rc-s...
-RC4wd TCI Scale R4 Transmission
store.rc4wd.com/RC4WD-TCI-Hea...
-RC4wd rear k44 or yota axle or similar (boom racing brx80 for narrowing the rear)
store.rc4wd.com/Yota-II-Ultim...
store.rc4wd.com/K44-Ultimate-...
rcaddict.com/products/boom-ra... set-w-ar44-hd-gears?variant=47619021111606
-Generic Rear leaf spring kit with shackles and hangers.
amzn.to/3wkAXAC
-RC4wd Scottsdale Body Set
store.rc4wd.com/rc4wd-chevrol...
-Lesu Drive shafts
www.semijoerctruckshop2.com/s...
-RC4wd 50mm-70mm shocks (bilstein 50-60mm)
-Assortment of M3 hardware and spacers (must have an assortment of M3 spacers)
teamknkhardware.com/shop/spac...
-Rods and Rod ends for steering links
-Micro servo (reefs Micro 99 or smart 179 recommended)
www.amainhobbies.com/reefs-rc...
-Motor/ESC and your own TX/RX
-R design micro servo horn with m3 holes
www.amainhobbies.com/rdesign-...
If you like shopping with Amain, please help support the channel and use the link below!
www.avantlink.com/click.php?t...
Check out my Amazon influencer store page for some of these products and help support the channel!
amzn.to/2NMKTtX - Auta a dopravní prostředky
Somebody start making ol school traction bars!
Another good thing about that boom racing axle is you could put whatever pinion angle you want without a shim
Damn i missed out on the kit cant wait till you restock i cant wait to build mine!
Glad to see the kit sold so well, too bad it happened before I managed to order one.
They are not available yet. Hoping to make them available Friday or Saturday.
I disliked the Dakota for many many years, until I drove one as a work/company truck. I couldn't say anything bad about it after actually driving one. It was also red!
Super cool kit. That Scottsdale looks so good slammed.
Sweet kit I wish you had a kit for the traxxas trx4m k10 to lower them the right way
This is neat gotta figure out how to add line lock and a mini smoke machine so you can do burnouts in the shop truck
Like the stance on the grey ish one,,,in the 90s that means fast lol. Good stuff, I like the idea that it's a kit that you can make it how you want it.
This stuff is very very cool! One day I'll be at this level but I'm just learning now. But your stuff is awesome!
That's is a very nice rc truck kit and it looks awesome man
Oh ok you havent actually sold them yet awesome cant wait to buy one hopefully before they sell out
This is cool cant wait to get one and itwould be cool if you can do a crew cab long bed frame option
Its a beautiful truck.
If i had the dough, I'd want wide slotted mags(the superwide custom machined ones on Facebook) and id just start cutting up buggy tires until i had something that looks right.
(Like a 295,50,15 square setup)
Its a nice setup your offering. I hope they sell like crazy! Good luck
The kit turned out nice.
wow very fantastic chassis~!!!!!!
Those are some damn nice kits man.
I can't wait till someone buy this chassis and make a bed dancer
redcats making one
Very cool build!
Redcat Racing should partner with you with this kit at least
The shop truck is looking mint, especially Grandpa's.👍🏻
Soo...how long till a drift shop truck is built.😁
I want to this chassis.
But I think this chassis needs differential gear.
That came out slamming good Josh. I used a 4tec front suspension on my blazer truck version but it’s a stock look. I’d like to use the new C10 with same set up but more scale. I like the SSD motor but only fits the smaller motor right?. The rc4wd motor might be too heavy for the limited shocks available.
The ssd fits a standard 540 motor just fine. Doesnt quite work with the 2 in 1's though. The rc4wd motor would need different mounts, the weight might not be too big an issue, could easily add or change springs in the scale shocks.
Yes amain indicates the SSD houses a 540 motor as the rc4wd v8 scale does. Do these get hot like they claim?. I don’t own a 540 do you need to minimize the run time to avoid the heat?.
I was 3rd person to like this video 💯💪🤪😜🤣
I was the 3rd person to Like 👍 your comment.
Awesome kit, even better looking laid down on the ground. But after watching the whole video I honestly like em both. If I order your kit could it be possible for you to add a cheat sheet of where to find the parts from Tamiya rc website? Thank you for the awesome video on the wide range of options on how to build something really badass.
I have a parts list in the video description and on the website. I cant give exact links to all the parts because as they sell the links will go dead.
@@RCeveryday thank you, going to be placing my order Friday. Can't wait to get my Scottsdale going. It's been on my shelf for a little bit now. Really liking your slammed down look. I have a ton of extra parts from rc4wd laying around my basement. You gave me a reason to use them. Wondering if a TF2 extra cab will fit? I've been wanting to slam a Marlin TF2 for a old school dirt bike hauler from the 80s. Thank you for making this possible to do now
How hard would it be to add axle wrap bar mounts to the 3-D printed crossmember in front of the rear axle?
Are you going to crawl fest at GSL ranch in Texas this April?
Going to try to. If just for a day at least.
Not sure if you have been but there was about 400 people last year. Good size.
I’ve been the last 2 years
Where do you buy the kits or the parts and pieces needed to build one? I have been wanting to get into building rc cars with my son
The kits I sell on Rceveryday.com. There is a parts list there as well as in this video description with links to most.
Anyone been able to fit other control arms aside from the TL01 ones? I can’t seem to find em in stock anywhere. Was thinking about a set of the MST drift arms
So far ive seen m-06 arms, although they are narrower, cc01 arms, and the GF01 arms and parts are identical to the TL01
Awesome. Never owned a tamiya kit so all their components are all new to me. Thanks man! Loving the kit so far!
I think you should sell two kit one like this and one full roller
What tires are those on the rally wheels plz thank ya
Old 1/8 scale model car tires
Does a parts list come with the kit?
It’s in this video’s description and on the website listing for the product. Just have to expand the product description on the store page.
I want to build a 1975 GMC Gentleman Jim
Nice video very very nice👍🛻🛻🫡👏👏👏
Is there a way to make it stock ride height?
close to stock, i show near the end of the video
Where are the wheels on granddads truck from?
They are traxxas 1.9’s from one of their blazers
@@RCeveryday what Bout the tires
So it's not a full rolling chassis your sell
No, its just the base chassis parts, just like the ratrod kits are sold
@@RCeveryday 155$ ? 100$ WHAT IS MORE RESPECTABLE