Another great video, I would love to see a video with the Match DSP using the OEM set up and the Match adapter the cable with the factory amplifier. On this you have to use all the inputs, in my case 9 along with the MEC analog in module. I think I know where to cross over all the factory passive mids and tweeters but what I would really like to know how to do is set my factory subs to be mid bass left and right and send subwoofer frequencies to the line out using a separate amplifier. If anyone knows if this is possible, please share. Thanks.
The only time we used a 1k tone in our vehicles was gain matching amplifiers, assuming there were multiple in play. Pink noise and a microphone for the rest.
@@JosiahBuwalda Thank you kindly for your reply, Josiah. I was excited to see a Helix DSP post and didn't realize your DSP is different than mine. I have the Helix M Four. I will look again and try this. Thank you
Hey Josh, I have 2017 BMW 330xi with HiFi sound, I have upgraded speakers, under seat subwoofers from bimmertech and also upgraded Amp with Bimmertech pp86dsp, I am not sure how to setup dsp for my sound setup, I would just need help about my setup. Thanks
Yea unfortunately unless they make a preset on the Audiotec Fischer website you’ll end up paying a tuner to setup and tune your car. Unless you figure it all out
Thanks for the vid. I just installed a P SIX and the software was quite overwealming at first. This helped me quite abit for the initial setup. I do have a question.. I have a legatia l12sw hooked to channels E and F for each coil. I basically have it setup exactly like this except i have Subwoofer1 selected for channels E and F. Is this the correct way to set it up? Thanks again
Yea the name of the channel is labeling and is just there for you to know what channel goes to which speaker. It doesn’t do anything to the channel It’s all in how you setup the crossovers.
@@JosiahBuwalda Perfect thanks for the explanation.. Ill keep those two channels linked to make sure xovers is identical between the channels. I'm playing around with it now and I'm quite impressed with the p six and sub in IB setup
Hi Josiah. I have a match 8 dsp and want to know if I can run just a virtual center only in the match software. I have a pic of the IO setup IM using 6 channels in and going full range to the FL FR RR RL sub1 sub2 and then 50/50 fr fl output to virtual E. Any tips or help would be great.
@@johncooke7191 Yes all the format is identical the GUI is the same across the board for all audio Tech Fisher products. The difference is the match is Meant More for OEM switch out stuff so the features and what the DSP allows you to do is what I’m unfamiliar with
I did, and you replied, on April 4th. I since purchased ScanSpeak Limited Edition D2604/8320-02 1" Textile Dome Tweeter, and the Alpine KTP-445A 4-Channel Head Unit Power Pack Amplifier Class D/ Alpine KTP445 for power. I've got to make pods for the tweets and install the amp. Hopefully will get it done early next week. I'll keep checking videos for tips on setting up an active 3way
Another great video, I would love to see a video with the Match DSP using the OEM set up and the Match adapter the cable with the factory amplifier. On this you have to use all the inputs, in my case 9 along with the MEC analog in module. I think I know where to cross over all the factory passive mids and tweeters but what I would really like to know how to do is set my factory subs to be mid bass left and right and send subwoofer frequencies to the line out using a separate amplifier. If anyone knows if this is possible, please share. Thanks.
Great video! Quick question. For the very first step setting gain sensitivity do you use a 1k 0db tone or mono pink noise?
The only time we used a 1k tone in our vehicles was gain matching amplifiers, assuming there were multiple in play. Pink noise and a microphone for the rest.
@@JosiahBuwalda yeah the manual says first step to test the input sensitivity if it’s less than 4 volts I believe to play pink noise 0 db.
@@JosiahBuwalda so do you not set your input sensitivity gains? and leave them at Min? If you do, do you use 0db pink noise?
Is there a way to change the subwoofer channel on the right of the IO settings screen to a full range output.
Sure. This page is just for labeling and directing the signal. If you bypass the crossover for the subwoofer then it’s full range.
@@JosiahBuwalda Thank you kindly for your reply, Josiah. I was excited to see a Helix DSP post and didn't realize your DSP is different than mine. I have the Helix M Four. I will look again and try this. Thank you
thx for the vid, helped me a lot
hey Josiah, great detailed videos. I have Match PP86DSP and have questions about settings, would you be able to help?
What are you trying to do?
Hey Josh, I have 2017 BMW 330xi with HiFi sound, I have upgraded speakers, under seat subwoofers from bimmertech and also upgraded Amp with Bimmertech pp86dsp, I am not sure how to setup dsp for my sound setup, I would just need help about my setup.
Thanks
Yea unfortunately unless they make a preset on the Audiotec Fischer website you’ll end up paying a tuner to setup and tune your car. Unless you figure it all out
Thanks for the vid. I just installed a P SIX and the software was quite overwealming at first. This helped me quite abit for the initial setup. I do have a question.. I have a legatia l12sw hooked to channels E and F for each coil. I basically have it setup exactly like this except i have Subwoofer1 selected for channels E and F. Is this the correct way to set it up?
Thanks again
Yea the name of the channel is labeling and is just there for you to know what channel goes to which speaker. It doesn’t do anything to the channel It’s all in how you setup the crossovers.
@@JosiahBuwalda Perfect thanks for the explanation.. Ill keep those two channels linked to make sure xovers is identical between the channels.
I'm playing around with it now and I'm quite impressed with the p six and sub in IB setup
Hi Josiah. I have a match 8 dsp and want to know if I can run just a virtual center only in the match software. I have a pic of the IO setup IM using 6 channels in and going full range to the FL FR RR RL sub1 sub2 and then 50/50 fr fl output to virtual E. Any tips or help would be great.
Unfortunately I’m not sure. I haven’t used the Match dsp in quite a while
@@JosiahBuwalda fyi it’s the same format as the helix in your video. Thanks for the response
@@johncooke7191 Yes all the format is identical the GUI is the same across the board for all audio Tech Fisher products. The difference is the match is Meant More for OEM switch out stuff so the features and what the DSP allows you to do is what I’m unfamiliar with
on m5dsp you cant change the IO ?
I wanna say no. Most of the Match stuff is made specific to just add power/dsp to a stock system and using one of the Audiotec Fischer harnesses
I have no sound with your most recent few videos, I have to us CC to watch them. What am I doing wrong? Sound works on all other youtube videos.
Abraxxas1127 I'm unsure I've had many people use these video in the last few days and they all had sound so i don't know know what to tell you.
Josiah Buwalda I see now that my center channel isnt working on my pc because I can hear perfectly on my phone.
👍
I have a question to ask regarding the IO setup of helix dsp. Can you provide your email add?
Kalaiarasan Munaindy , jbuwalda@hybrid-audio.com
+Josiah Buwalda will contact you soon . Thanks ya
I have a question regarding 2 way active, hope you don't mind that I email you also.
Did you ever email me?
I did, and you replied, on April 4th. I since purchased ScanSpeak Limited Edition D2604/8320-02 1" Textile Dome Tweeter, and the Alpine KTP-445A 4-Channel Head Unit Power Pack Amplifier Class D/ Alpine KTP445 for power. I've got to make pods for the tweets and install the amp. Hopefully will get it done early next week. I'll keep checking videos for tips on setting up an active 3way