FDM resin Printing with LASERS and a 3D Printed PUMP!
Vložit
- čas přidán 25. 06. 2024
- Head to squarespace.com/PROPERPRINTING to save 10% off your first purchase of a website or domain using code PROPERPRINTING
In this video I show how I print UV resin on a standard FDM printer. This has two main challenges: pumping the resin and curing the resin. I chose to use a peristaltic pump so the mechanics don’t come in contact with the resin, but I had to solve the pulsating problem of this type of pump. For curing the resin, I use standard low power lasers.
Thanks 3DResyns for supporting me with your resin! www.3dresyns.com/
Please use one of my affiliate links to support my work:
The laser engraver: geni.us/zP7HX
The equipment I mostly use:
FDM printers:
- Creality Ender 3 pro: geni.us/KDfgpA
- Creality Ender 3 S1 pro: geni.us/n03Ah
- Creality CR-30 Printmill: geni.us/8zMA
Resin printers:
- Anycubic Photon Mono X: geni.us/Ijcw2
- Anycubic Photon Mono X 6K: geni.us/hRMBSB9
- Anycubic Photon M3 Max: geni.us/8wGZDd
The software and sites I use:
-Music source: Epidemic sound www.epidemicsound.com/referra...
Check the merch on merch.properprinting.pro/
My designs can be downloaded from my website www.properprinting.pro/
Consider becoming a Patreon supporter: www.patreon.com/properprintin...
Or buy me a coffee! ko-fi.com/properprinting/
Chapters:
0:00 Intro
1:01 The pump
3:01 First prototype
4:17 The pump challenge
5:13 The non-pulsating peristaltic pump
6:59 Squarespace
7:41 Laser module test
9:35 Adding glass fibers
12:13 Next glass fiber design
14:07 The tape solution
15:27 First printing attempt
16:31 Actually making use of the laser
17:59 Sum up of first attempts
18:30 The improvement
19:24 Using an actual hotend
20:24 I want that bottle opener - Věda a technologie
Hi guys! I arrived in Chicago after a long trip to go to MRRF! I haven't gotten the time yet to respond to your questions and suggestions, but I soon will. Maybe meet you there!
Aw, man. I couldn't make it this year. 😢 I hope I get the opportunity at a future MRRF. Have a good time there!
Awesome work on this - I can't wait to see what comes of it.
Welcome to 🇺🇸, swing by Denver, I'll buy that coffee I owe you!
You don’t have the squish of SLA and you are not doing small cross section free form print so To counter balance the tiny surface tension effect. Start by printing the inside wall and apply a Z shift at each layer. That should do the trick and allow you to use low viscosity resin which would be the easiest to prevent leaks
Absolute pleasure to meet you at MRRF. You’re the best kind of a mad scientist!
Awesome experiments. Great note on safety for the lasers, but you missed a very important warning with this type of work. Photopolymer resins give off heat when curing. If you have some on your hands (even with gloves) it can burn you if it starts curing - if too much uv light hits the spot. Be careful, even a smudge can burn you to blistering level.
Hands down one of the best printing youtubers a lot of people don't know about.
Hands down thumbs up
Just found out about him and he got a sub about 2 mins into this vid.
Yup, very high quality video too, camera wise
The worst part about your videos is that they end. I need to see this succeed now, i'm invested! :D
Thin the mix. Add a tiny spray head of resin, like spray painting, the laser cures the "paint". Attach a standard 3d print head to your rig. Precise controlled color depths for 3d prints. This way its lack of layering is a benefit. Easy to scale up to full color printing. You could also combine it with a 3d scanner and make an automated 3d coloring device for existing 3d prints.
We're going to get this to succeed!
@@properprinting Why are you curing the resin right near the print head. Put a shade system so that what you are actually printing doesn't get cured until it moves outside of the print area. Also the fibre optics. make a loop, and sand it. The light will come out the sides instead of the end.
This was the toughest video I've made so far. I badly underestimated FDM printing with resin, but I'm happy with the result. The pump on itself already enables some interesting possibilities for the extruder series! If you've got suggestions on how to FDM print resin, than let us know in the comments!
What about turning off the laser on travel moves? If you are controlling it with the fan output, you can just wrap all G0 moves in M107 - M106. Then even if it leaks resin it will stay liquid. Also in DIW adding a filler to change the rheology is very common (eg SiO2 or TiO2).
PS is the pump design uploaded somewhere? Kinda want to try it out
@@SilvioTisato You could even program firmware retract to do that.
@@daliasprints9798 Yep, although that depends on the firmware you're running. I know for sure you can do it with duet, but I haven't had to do it with others. Also you might want retract to lower pressure in the needle, though that quickly result in air bubbles. The M106-107 is just a regex substitution
Interesting idea, love it! On a topic of predictable flow I would suggest trying a system with a reservoir residing above the printer(maybe on a shelf) such that it can introduce a manageable pressure in the tube. Pump may add the resin to the reservoir at a predictable pace and reservoir will act a a buffer to have enough resin to keep needed pressure. Then the two challenges still left: a) stop the flow and b) control the flow intensity. To be able to stop the flow I would add a small solenoid to close the resin output right at the print head; just before the nozzle. And to be able to control the flow I would try to have a prolonged/rectangular shaped reservoir, such that when rotated/tilted the height of the resin change and pressure change with it. Idea with tilting resin reservoir will require a motor of some kind. This whole idea is very dependent on ether ton of experiment or a mode to predict its physical behavior. Anyway, good luck with the project!
How about spraying the resin, that way you could get higher resolution as well.
You sir are a mad scientist and I love it!
What’s up Uncle Jessy! Fancy seeing you here!
When people are amazed by engineers they think it’s just because of how smart they are. In reality it’s often the dedication and patience that makes them uniquely capable.
Very true. Most people see just the finished product, not the (sometimes many) iterations to get to that point.
All it takes is an ambitious person who is mechanically inclined. Anyone 3d printing should already be mechanically inclined.
The pulsation can be solved by using 2 tubes. Both tubes run on the same set of rollers but the outside housing has a phase shift for both tubes. This way the pulse of 1 tube falls in the dead period of the other.
Watson Marlow (Dutch peristaltic pump manufacturer) has a few model doing this running in the lab here.
Thanks for the info! As it looks for now it seems not to be pulsating too much with this design. One tube makes it easier to work with, so I hope I can stick to it.
And we have car engine
you need gel instead of liquid, liquids will move on you before curing and it retracts unpredictably. I would like to see some trace testing to tune every parameters, you can't use standard fdm parameters. You need to cover a wide spectrum of values because you're into unknown territory. We don't know if the fluctuation in extrusion is causing real issues. When the first layer is nice, then test to stack them and succeed to have consistent height. I would try pointing the laser on the nozzle and use high speed printing to avoid clogging. Considering each layer will cure more previously laid ones, the power of the laser needs to be tuned to barely solidify the resin with one pass, this will reduce clogging. We can check if the layers need to be thinner than the nozzle diameter and if prefers over or under extrusion. if the resulting parts are tacky, it's not an issue you can cure them after.
16:48 - So the resin itself is acting as a light pipe, allowing the reflected UV light to travel up the nozzle and prematurely cure the material. I didn't see that coming.
So kinda "upstream contamination" but with light. Maybe printing with dark / black resin could prevent it? Or maybe just adding some coal powder / dark pigment to existing resin could do the trick?
@@puerlatinophilus3037 TiO2 works too (white pigment), it absorbs UV really well. But dialing in the amount of pigment is not easy.
@@adamrak7560 Sad that this means another limitation but depending on the resin's thermal resistance, it is a possible upgrade in some context
@@puerlatinophilus3037 the resin itself needs this light pipe type of process (penatrating) in order for any curing past the surface level of the print regardless of the method used to print.
I think what we are seeing here is actually seeing. How we know an object is somewhere generally relies on light waves reflecting from its surface or the absence of that. This is no different. The laser light is reflecting from the surfaces and penatrating the nozel. Either controlling the light or shielding the actual nozzle or both is what will be needed.
But I guess if it was that easy, they would be mass produced and on the market by now. So what do I know.
I think I did this manually many times in the lab from 1999 to 2007.
Your zero-pulse pump solution surprised me, very cool and elegant. I thought you'd need two running out of phase into a Y-adapter.
I think this would work. You can use the same motor and just use a stacked design but with offsets. Y's on the ins and outs.
Having an oblong or egg shape may reduce the pulsing and improve consistent flow.
Absolutely love your videos! The thing I love most is watching you work through issues and roadblocks. Not only have I learned a ton from watching your videos, but you've inspired me to be more experimental. Some of my experiments work out, some don't, but the most important thing is I learn from each and every one.
Awesome, I'm so glad to read this!
Have you tried/considered a non translucent resin? I think ideally something dark like black. I think the issue is that the resin refracts some of the laser internally, and funnels it up the nozzle opening like an optic fibre. Perhaps a less translucent resin would prevent this. It would be a lot slower but you could also try doing dropwise extrusion (and retract to break the physical connection between the resin in nozzle and the print, possibly mitigating the optic fibre like effect)? or print a layer then cure it?
The resin needs to be translucent else the UV won't reach and cures the inside.
I'd print an entire layer and then move the nozzle out of the way and blast the build plate with uv
@@durandalgmx7633 Don't forget that even visually opaque resins could be translucent to the UV.
@@bryanst.martin7134 That's true
I was thinking along that line as well, when you watch Joel's video the resin used is an opaque white. A different resin should do the trick, hope it gets resolved it would be an awesome addition to the tool box.
Maybe more like an ink jet and pulsing the laser…
But bravo again. Every issue I wanted to make a suggestion and each time you made the same conclusion. Love it
thats how the commercial FDM uv gel printer works
I have made some projects similiar to yours, i like finding someone with similiar problems and stuff (but you are way better i'd say) i can't find anyone like you you are severely underrated
Man, you do the coolest experiments!
One note on the optical fibers, they can actually fail to reflect the light along the fiber if the bend radius is to small, maybe that was also a reason why the first design failed
Bingo.
Whilst we can see “some light” at the end of the fibres, some materials have much lower transmission at UV wavelengths.
For example Germicidal 250nm fluorescent tubes have to be made with quartz as glass filters a lot of the energy at this wavelength.
I suspect end polishing of the fibres also has an impact.
In this case it was because of the fucked up surface. One cannot cut fibre optic cable with a kitchen knife and expect it to transmit light perfectly. The cables must be cut with a special tool that makes sure the surfice is perpendicular and doesn't have defects. You also need to align very well the start of the fibre to the laser beam making sure it also is parallel to the beam. If the laser is coming at an angle, there will be huge reflections at the beginning.
I liked his idea don't get me wrong, but it is pretty clear he didn't research how fibre optics cables work
I like this guy. I just found this video and he seems to not pretend to know what he's doing but at the same time knows how to make things work. Very fun to watch.
I love that you don't back down from a challenge. That is the attitude!!!!
Edison would have been proud of you as this is a perfect example of his theory of repetitive experiments where creative failure leads to progressive knowledge accumulation. Good Work.
Best music of any 3D-printing CZcams channel for sure.
Your ingenuity is really astonishing!
keep up the great work an videos!
I had this idea a long time ago back when there was a kickstarter for a UV resin pen. I forgot about it entirely and I'm glad you have taken the time to work on this.
Jon, you truly are a madman. And we all love it. Keep doing what you're doing
This is actually a really brilliant idea. Way less messy than a normal resin printer.
a highly underrated channel, I want to come back to you have a million+ subscribers... keep up the fine work
I love your ingenuity in making stuff. So happy to have found you.
Haven't been this captivated by a video in awhile, truly great content.
I absolutely cannot wait for the follow up on this. I thought of doing this the other day, but you've gone and done it! Good work getting so close! I want to see this become possible!
You're completely MAD ! I love it !
Mate you have the best 3D printing channel by far.
Whether you get this working or not, this project and several other videos on your channel are truly inspirational! I don't have anywhere near your level of design skills or engineering knowledge, hell, I don't even own a 3D printer but I can't wait to see what you come up with next!
Goed bezig kerel! 👍
It's always a good day when there's a new Proper Printing video.
You are the most Swedish person I have ever seen. You are the literal stereotype of a Swede. I have a Swedish friend and he agrees. So I can’t be wrong. 😁
I just love your perseverance and patience! With your ingenuity, you will get this done I am certain. What a process! But, what a great idea!! Keep going ...
OMG... that video was amazing! I love to see the progress in that
That was completely epic. I felt every fail, and rebuild. You have such amazing ideas.
Love the clean editing and montage coupled with a quiet chaotic energy seeping through. Keep up the good work!
Super inspiring to see someone beyond a large company is finally experimenting with this.
Bro! You are just Nikola Tesla of 3D printing! Never give up and keep going!!!! We all love you ❤️❤️❤️❤️❤️
Loved it. I've been meaning to test this same thing for years now, you gave me a lot of answers and I enjoyed the process! Thanks, subscribed!
I love your engineering approach, great results, keep it up.
You Sir, have patients of steel! Ingenious problem solving here, keep going!! I wish you all the success with your creations!!!
Great vid! Seeing the whole process and all the things that didn’t work is super-valuable. Whatever you’re showing may not be immediately or directly applicable to any specific project I’m working on, but I get a tremendous amount of learning and understanding from watching your vids! 👍👍👍
Great video. I love your approach to developing the process.
Simply amazing, you are a hell of an engineer! Congrats man
This is so cool man. Great perseverance!
This was amazing! Nice print!
Love it, I understand you pain always have more material on hand as the first time you don't succeed try, try, try, and then try once again thank you for showing your struggles 😊
I love it! I had this idea that was "kinda" like this, but instead it was using a "Flatbed UV Printer" but still print in 3D. I cant wait for the future!
Brilliant!!! Very Cool 😎 You always impresses me with new technology/idea in very practical home brewing approach.
Absolutely awesome work , the design you have made is cool. And as usual your video is entertaining and teaches us allot. Thank you Jon.
this is the future keep the work !!!!
No words, just awesome!
Awesome project and progress, as always!
You’re such a brilliant young man.
Great video - really interesting to see the difficulties in practice, showing it's far from trivial to engineer.
This is great. Love your work!
excellent attempt - really enjoyed the process
So cool that you are working on this.. I had thought about doing this for a while but you are doing it! I wish I could work with you man.. Love your vids. You crack me up somtimes.. Peace brother Rolfie
brilliant man ive been thinking of doing the same thing for some time. glad the lazer is working like i thought it would
The beer seemed to be the most satisfying for you! Never give up!
I totally had a similar heat related issue when playing with the plastic optical fibers on a project. Even got glue would partially melt the fibers, and be responsible for blocking the proper light transmission. I felt your pain my friend.
So good!
I love the fails as I love the results.
Watching you be frustrated is more satisfying than when I actually get something to work.
You do a very clean job !
Haha that's so awesome man. I love your videos soo much. You are an inspiration. Keep them coming
super amazing! very cool stuff man!
Love the idea of this video. Look forward to more content on this idea!
I work with lab instruments that use peri-pumps. They have a lot of advantages, such as easily adjusting flow and volume by changing the ID of the pump tubing.
You can eliminate the pulsing by using the flexibility of the tubing between the pump and nozzle as a pressure receiver.
If the flow from the pump is slightly higher than the nozzle size can handle, the tubing between the pump and nozzle will pressurise and expand slightly , acting like bellows to absorb the pressure pulses.
Also, having more rollers reduces the volume of the tubing between rollers and therefore the volume that is pumped with each revolution. Most commercial peri-pumps use only 2 or 3 rollers.
I used to use peristaltic pumps. I also recall them only having about 3 rollers and they definitely delivered continuous flow to lab instruments. I remember calibrating the flow and we used special tubing in the actual pump section with coloured tags on each end which indicated the flow range based on ID, these tags locked in place to stop tube movement and put the tube in the pump under slight tension.. helps with pulsing and stops tube feed.
Main issue with a peristaltic is over time it damages the tube changing the flow or even wearing through completely. So another reason for the short section in the pump as you just replace that small length each time.
Overall I think he should take a quick look at lab grade peristaltic pumps as they solved all these issues decades ago.
@@RocketMagnetUK I agree . There are many different designs. I have even seen hospital infusion pumps that used many flat plates operated by a helical cam to pinch the tubing in a continuous wave.
A company like Watson Marlowe would be able to give him all the information he needs
this open another level of 3d printing
You tried the idea that I have been thinking of for about a year, great job! I would use multiple UV LED's in a circle pointing at just below the nozzle. The point is you don't need to fully cure the model during printing, so you won't need that much power delivered by a UV laser. The model can be fully cured later in a UV chamber, we just want this to get the proper model shape in the first place.
Amazing work! That was a hard earned beer!
omfg this is brilliant! absolutely brilliant!
Really cool solution to reduce pulsations in the peristaltic pump! I've only ever seen pulsation dampeners used before...
Hey man.... greetings from Brazil. Long time no talk!!! I told you your channel would bem twice as mine in no time didn't I? Congrats your videos are awesome as always!!! The Karmeliet in the end is just the cherry on top!!! Best Beer ever!!!
You did! Thanks man :D
Excellent work!
Printing is looking great, very confident you will get this right.
If you wish to steady the flow from your pump fit an accumulator. They are used to even the pulses created from a pump system easy install.
GO... ver. haha Awesome once again Jon!
Always great videos
Inkjet printing has had similar flow issues with nozzles, one of the ones that worked well there was with a piezoelectric crystal for a drop on demand printhead. This was used to control droplet size and speed of droplet ejection from a reservoir.
Very exciting to see this, looking forward to more updates.
you sir, are amazing. thank you for your work
I effin love this guy
Keep at it man !!
Great video despite the fall
OK that's the first time a subscribe prompt has been so epic it made me immediately subscribe.
wat een video zo cool dat je gewoon het probeert en niet opgeeft als het een keer mis gaat super goede video
Bedankt Thomas!
Awesome video. Great work. 👍
Cool idea dude!
Great attempt. Kudos!
Commenting before finishing the video, I just had to say that the water printing part had me genuinely laughing, thank you for this great video and all your efforts.
Very cool concept.
I love the idea for the pump design. I'm designing a powder binding 3d printer, the pump and the printhead is basically what I'm looking for to improve the design. Thanks
Great video, even with nordic accent you make it look good. Well done.
no suggestions just a wow for even doing this.
tremendous challenge, that effort was titanic, a lot of desperation, but science is like that, success and error, greetings from Mexico, I am attentive to your videos.
You’re a mad man! I like it
Wow, what a cool video and idea! I've seen some great suggestions in the comment section about pulsing the lasers. I am not an engineer by any means, but perhaps a "simpler" first attempt would be to extrude the resin with the laser off, then run the same path (without extruding the resin) with the laser on to cure the resin. The higher viscosity resin would probably be more ideal, since it better resists flowing away from the previously deposited layer. Yes, you are running the same print moves twice which will greatly increase the "print time", but I don't know that speed is necessary concern at this stage. Just an idea (maybe others had it in the comments too). I am looking forward to your next video!
Ive definitely thought about this from time to time. Love to see someone doing it! I have also wondered about using lasers as an active post processing process on an fdm printer too. Maybe the next project?
Amazing man! You should definitely keep working on this!
Maybe try with pulsing the lasers? More like when laser engraving something grayscale. But that could be quite tricky on the gcode side.
Great work!
Hi Adam, I tested this solution last year and my best results were on my old coreXY by reversing my bed plate and axles. print upwards, the resin holds better to the plate and the prints are clean!