Vevor CUT50P Plasma Cutter Review & Testing (

Sdílet
Vložit
  • čas přidán 14. 01. 2023
  • I've always wanted a plasma cutter and I had the good fortune of being offered one by Vevor, a company that sells a vast collection of products across many categories including welding, which includes plasma cutters.
    * VEVOR CUT50P Plasma Cutter, 50Amp, Non-Touch Pilot Arc, 110V/220V:
    - Vevor Website: s.vevor.com/bfP6bS
    Be sure to use Discount Code VVMH5%OFF for a 5% discount!
    - Amazon: amzn.to/3irZq0q (No discount offered)
    Safety Accessories:
    * 3M Half Facepiece Reusable Respirator: amzn.to/3IRiEaw
    * 3M 2091 P100 Particulate Filter, 3 Pairs: amzn.to/3XtVivC
    * 3M Safety Glasses, IR Shade 5.0 Gray Lens: amzn.to/3CMX9Uw
    Note: Links to Amazon products are Amazon Affiliate links that won’t cost you any extra, but will help support my efforts with a small commission on qualified products. Thanks for your support!
    Visit my Amazon Affiliate Store: www.amazon.com/shop/diymyway
    Visit DIYMyWay.net: diymyway.net/
    #diy #outdoors #vevor #plasmacutter

Komentáře • 96

  • @MyClutteredGarage
    @MyClutteredGarage Před rokem +2

    Excellent, Martin! I’ve been wanting a plasma cutter as well. Looks like Vevor carries some interesting products. Thanks for sharing. Great edit!

    • @DIYMyWay
      @DIYMyWay  Před rokem +2

      Thanks, Ed! Plasma cutters are fun and useful, but like welding, it takes practice to get good results. Yes, I was surprised at the number of products the sell across so many categories. Thanks for watching!

  • @TheDavidarlen
    @TheDavidarlen Před rokem

    I did not know where to install the air filter until I saw you install it on the back of the machine thanks David.

    • @TheDavidarlen
      @TheDavidarlen Před rokem +1

      I looked on mine, no screws? So I drilled a couple of holes in the side sheet metal and mounted it.

    • @armadillospaz
      @armadillospaz Před rokem +1

      Same!! I just got mine and no screw holes but I popped off one of the screws on the side and mounted the regulator there. Seems better than what they intended too bc now is not blocking the fan!

  • @RB-tt9go
    @RB-tt9go Před rokem +1

    Hi Martin, I have often wondered about these Economical plasma cutters and whether they would actually perform. This really proved they do work! A great informative video. Would be great to see a follow up after several months of good use. Take care

    • @DIYMyWay
      @DIYMyWay  Před rokem +1

      Hi R B! Yes, they do work. Hopefully this one will for a long time. I’ll almost certainly do a follow-up video. Thanks for watching!

  • @FromSteelToWood
    @FromSteelToWood Před rokem

    That is likely to be my next tool to buy! Thanks for doing that honest review. I've checked on Vevor, they have their specific Canadian website and this model is available for us too! Thanks!

    • @DIYMyWay
      @DIYMyWay  Před rokem

      A plasma cutter is a great tool to have and I know you could do amazing things one, Joe. Thanks for watching!

  • @qfdforme
    @qfdforme Před rokem +1

    Excellent addition to your shop. Vevor chose wisely to do the product review. By the way, these Chinese made CUT50 plasma cutters are notorious for not achieving 50 amps output. If you have a clamp meter you can check it yourself. That said, these low cost inverter plasma cutters are a cost breakthrough for the consumer. I have three CUT50 inverter plasma cutters and a 1990’s 30 amp Thermal Arc transformer plasma cutter. These inverter plasma cutters are a great value. Thanks for sharing.
    Bill S.

    • @DIYMyWay
      @DIYMyWay  Před rokem +2

      Hi Bill! I hope it proves to be an excellent addition. Time will tell. I’m not surprised they don’t put out the full 50 amps,but I think it will be good enough to learn on and for most of my projects. You’re right, they are a great value. Especially when they’re free! 😁 Thanks for watching!

    • @qfdforme
      @qfdforme Před rokem +1

      @@DIYMyWay
      You are going to enjoy the convenience. They are extremely handy for cutting up salvaged steel like we both try to do. For example, Steel mattress frames can be quickly cut up and reclaimed into useful angle iron in no time.

    • @qfdforme
      @qfdforme Před rokem

      @@DIYMyWay
      Yes, free is good, but a professional video like yours is worth a whole lot more. 😃😃

  • @samengler539
    @samengler539 Před rokem

    Nice job Martin see you on your next project.

    • @DIYMyWay
      @DIYMyWay  Před rokem

      Thanks, Sam! See you there!

  • @martyb3783
    @martyb3783 Před rokem

    Very interesting. As you said, you will get better with practice. Great video as always Martin.

    • @DIYMyWay
      @DIYMyWay  Před rokem +1

      Thanks, Marty! I certainty hope I get better. PLENTY of room for improvement, that’s for sure!

  • @phattdaddy63
    @phattdaddy63 Před rokem +1

    Congrats on your plasma cutter Martin!
    You need a lathe and milling machine next and you will be ready to open for business.
    Thanks for sharing!

    • @DIYMyWay
      @DIYMyWay  Před rokem +1

      Thanks, Kenny! I haven’t ruled those out, but I think I need to practice more with the plasma cutter and my welder before investing in any more metal working machines. Thanks for watching!

  • @MJADoingStuff
    @MJADoingStuff Před rokem +2

    Awesome video Martin 😁👍 Glad to see you got a plasma cutter you are going to enjoy how convenient it is besides the mess. Good idea to have a respirator too. Thanks for the video 🚜💨🍳☀️

    • @DIYMyWay
      @DIYMyWay  Před rokem +1

      Thanks, Mitch! Yep, plasma cutting is very stinky business but I could smell anything while I had the respirator on.

    • @MJADoingStuff
      @MJADoingStuff Před rokem +1

      @@DIYMyWay Hey Martin check out Mike Festiva’s channel he made a work bench side mount water table for his plasma cutting needs😁👍

    • @DIYMyWay
      @DIYMyWay  Před rokem +2

      I watch his channel. He’s quite creative and has plenty of welders and plasma cutters to play with. 👍

  • @stanleyconrad4234
    @stanleyconrad4234 Před rokem

    Thanks for sharing Martin. I’ve become more of a visual learner in my later years, possibly due to “life events”. This video will prove helpful for when I unbox/set up my plasma cutter. I ran out of time to use it as I ran out the door to my winter home in FL. Miss my tools and tractors. Can’t have everything it seems. You do inspire me to be more orderly, but 7# in a 5# shop makes it a real challenge. As you recently pointed out, whatever size you think you need, add 50%.

    • @DIYMyWay
      @DIYMyWay  Před rokem +1

      You’re welcome Stanley! Sorry you didn’t get to use your plasma cutter before bugging out to FL. Sounds like you need some tools and a tractor in FL to avoid withdrawal. 🙂

    • @stanleyconrad4234
      @stanleyconrad4234 Před rokem

      @@DIYMyWay Hello Martin. I actually have a fair amount of tools here, for a snowbird. I bought a small Kubota 4x4 to “repair” due to boredom. The HOA will go bananas so it’s at a buddies on the river. Wish me luck.

  • @3DAstroTC
    @3DAstroTC Před rokem

    Excellent video! I have this cutter arriving in a couple days, looking forward to using it! I have a Vevor tig welder with similar troublesome gas connectors, hopefully they address that and go with something less problematic.

    • @DIYMyWay
      @DIYMyWay  Před rokem +1

      Thanks! Glad it was helpful in your decision. Good luck with your plasma cutter.

  • @watershedoverlook
    @watershedoverlook Před rokem +2

    Well the air hose fiasco is pretty inexcusable, but beyond that, it looks like a pretty capable unit given the price point. Great review as always Martin. 👍

    • @DIYMyWay
      @DIYMyWay  Před rokem +2

      Totally agree, Chris! No excuse for the poor fit of the air hose, but fortunately easily remedied. Thanks for watching!

  • @peacefieldfarm_mn
    @peacefieldfarm_mn Před rokem

    Nice video, Martin! In my last video about plowing snow, Jason made some modifications to my back blade using a plasma cutter, among other things. What a remarkable tool! Way better than cutting with an oxy-acetylene torch!! Cheers!

    • @DIYMyWay
      @DIYMyWay  Před rokem

      Thanks, Michael! They ARE remarkable for sure, and FUN too. Thanks for watching!

  • @theoriginalbubba1036
    @theoriginalbubba1036 Před rokem

    Nice little machine.
    I envy the pilot arc. I have a cut-50 that has served me for years, but it is drag start.
    I'm no pro, but It looked to me like you could crank up the air pressure a good bit bit. A quick trip to the hardware store you could pick up a good gauge and some better fittings...
    Keep an eye on the sparks on the back of cut, you want them coming straight-ish ( slight angle on thicker stuff) off the back. if they are flying sideways you are gouging more than cutting.
    It took me a good while to get used to setting up (much like it did learning mig welding), but I have slogged through 5/8 plate with mine (wasn't easy or pretty but sure beat a cutoff wheel!)
    Looking forward to seeing what you make with it!

    • @DIYMyWay
      @DIYMyWay  Před rokem +1

      Thanks, Bubba! Yeah, I’ll experiment with higher air pressure and probably buy a gauge that reads in PSI. Thanks for the tips and for watching!

  • @tractortalkwithgary1271

    That is a sweet little unit Martin. I would sure have to think that it is well worth the money.

    • @DIYMyWay
      @DIYMyWay  Před rokem

      Seems to be, Gary. Time will tell whether it holds up well. I’ll be practicing some more soon so we’ll see. Thanks for watching!

  • @bertdiver3708
    @bertdiver3708 Před rokem +1

    either heat up the hose or use isopropyl alcohol to lubricate and evaporate quickly

  • @GrampiesWorkshop
    @GrampiesWorkshop Před rokem

    How's she goin'? It'll be nice to have the plasma cutter. I have been dreaming of one for some time now. This looks like a good DIY occasional use model. Thanks for sharing and good luck with your new cutter!!!

    • @DIYMyWay
      @DIYMyWay  Před rokem +1

      Hi Mike! They sure are handy to have around. Yes, it seems to be a good fit for DIY occasional use. Thanks for watching!

  • @earlyriser8998
    @earlyriser8998 Před rokem +1

    looks like fun

    • @DIYMyWay
      @DIYMyWay  Před rokem

      It is fun! Thanks for watching!

  • @LittleShadowWoodcraft

    Hey Martin. Great video! I like how you went through the trials and tribulations of the machine.
    I have one coming in the next couple of days.
    I have one question for you. How many amps is your 220V breaker? I have a 30 amp breaker on my circuit. Would it be prudent to bump it up to 50 amp?

    • @DIYMyWay
      @DIYMyWay  Před rokem +1

      Thanks Shane! The breaker on my 220V circuit is 50A. Enjoy your Plasma cutter!

  • @semo-dyer5183
    @semo-dyer5183 Před rokem +1

    Hi Martin, Thanks for the video. I was thinking about picking one of those up for awhile now but hesitant until I saw your video. Have you had more time to practice on it? If so would you recommend the Vevor?
    Thanks, Bryan

    • @DIYMyWay
      @DIYMyWay  Před rokem +1

      Hi Bryan! No, but I expect to in the next couple of days and will probably make a video of my practice. I’ll have a better feel for it then. Thanks for watching!

  • @dustysnow2502
    @dustysnow2502 Před rokem +1

    If you have any land to take care of you gotta have a tractor. If you have a tractor you gotta have a welder. If you have a welder you gotta have a plasma cutter. And you're right. Fun, fun, and more fun along with the joys of being unstoppable.. somewhat.

    • @DIYMyWay
      @DIYMyWay  Před rokem +1

      Right you are, Dusty! “Somewhat unstoppable.” I like that description! Thanks for watching!

  • @tractortalkwithgary1271

    I wonder if soaking the end of the air hose in some really hot water would help that to slide on easier

    • @DIYMyWay
      @DIYMyWay  Před rokem

      Hi Gary! Yes, it probably would. Good idea!

  • @brianroth7852
    @brianroth7852 Před rokem +1

    Martin, ? Have you tried cutting 1/2" mild steel yet. And if so how did the unit perform.

    • @DIYMyWay
      @DIYMyWay  Před rokem +1

      Hi Brian! No, I have not. Thanks for watching!

  • @seanseoltoir
    @seanseoltoir Před rokem

    There would be a way where you could get 110V at 40A... You would need to plug two extension cords into two different outlets which were on different circuits, but were also on the same side of your circuit breaker box... Then you would need to wire that into an adapter that combined those into a single 110V receptacle... Unfortunately, the highest rated receptacle that I've seen is 20A though... On the other hand, if you have two outlets that are on different sides of the circuit breaker box, you could get 220V out of it if you wire it correctly... If someone doesn't understand how this might work, and how to verify that they are using the right wires, then they probably should not be attempting it...
    The above comment is based on the unit I bought (PlasmArgon) that came with the standard 110V plug instead of the 220V plug that is on your unit. Your unit's electrical connection is designed better in my opinion... For your unit, you could create a conversion adapter that had a 220V receptacle on on one end and two 110V plugs on the other end. This could be wired similarly to my description in the previous paragraph so that you either get higher amperage 110V (e.g. 110V @ either 30A or 40A) or get 220V @ 15A or 20A. Most 110V house circuits are 15A, but *some* are 20A.

  • @oxford821
    @oxford821 Před rokem +1

    What is the purpose of the grounding clamp?

    • @DIYMyWay
      @DIYMyWay  Před rokem

      I imagine it is to make sure the piece you are cutting doesn’t accumulate a potentially dangerous electric charge. Thanks for watching!

  • @ItsaboutMakingnotBuying

    Martin you may want to increase the air pressure so it blows thru. Try around 60 psl. Hope you like it as much as I like mine. Later

    • @DIYMyWay
      @DIYMyWay  Před rokem

      Hi Mech! I forgot to mention it but I did increase the PSI to about 60 when I got to the thicker material. When I practice next time, I’ll try it without the standoff, which made it harder to pull it along at a consistent speed. I know I’ll burn through the consumables quicker but they’re fairly cheap and most pros I see don’t use them. Thanks for watching!

  • @rodbagley1686
    @rodbagley1686 Před rokem +2

    Wonder what that does to your electric bill? Probably about the same as a welder but I have no clue. Does look like fun.

    • @DIYMyWay
      @DIYMyWay  Před rokem +1

      Hi Rod! I expect it raises my electric bill, like everything else I plug into a socket. The question is by how much. The answer is I don’t care, because - as you said - it’s FUN! Thanks for watching!

    • @seanseoltoir
      @seanseoltoir Před rokem

      Well, if you have to cut something, you're going to be paying one way or another... There are going to be fuel and consumable costs... Even with a *hacksaw*... Hacksaw blades don't last forever and then you have to factor in the fuel/consumables (beer), especially on a hot day... :)
      My welder is on a 60A circuit, so I know that it won't be using any more than that... 220V at 60A = 13.2 kW... Assuming $0.15 per kWh, that works out to be $1.98 per hour to weld if I was welding with a 100% duty cycle welder at 225A... My welder does 225A, but definitely not at 100% duty cycle... I suspect that this cutter would use half of that at its max setting and even if that allowed a 100% duty cycle, it's unlikely that most people would be using it continuously for that long... Of course, you need to add a bit to that $1.98 per hour to cover the cost of running your air compressor (perhaps 12A at 110V)...

  • @robertkovacs7962
    @robertkovacs7962 Před 8 měsíci

    Turn the air pressure up!

  • @keithrayeski6417
    @keithrayeski6417 Před rokem

    Oh now Martin!! I just bought two Craftsman LED tri-pole leg stand lights!! How will I ever justify THIS to the Mrs?!?!🤫
    Let’s review. You popped the 20 amp breaker at 30 amps on 110v. But no issues at 50 amp on 220v? My 220 welder outlet is a 30 amp breaker. Do you suspect I may have issues at 220v with a 30 amp breaker? Sure makes cutting metal a lot less stressful!😁
    Thanks for sharing!!
    Oh, and happy new year!!🎊

    • @ItsaboutMakingnotBuying
      @ItsaboutMakingnotBuying Před rokem

      I have my plasma on a 220v/50amp outlet no problem.

    • @DIYMyWay
      @DIYMyWay  Před rokem

      Hi Keith! That sounds like a personal problem to me. 😄 Yes, that’s right. My 220V outlet is 50A which can handle the load. The specs say the plasma cutter takes 50A at 220V on full power, which I doubt but it could be true. If your outlet is a 6-50R and the wire going to it is 8 ga copper or bigger, you can probably just replace the breaker with a 50A one. When in doubt, consult an electrician. Thanks for watching!

  • @DELTRANIO99
    @DELTRANIO99 Před 3 měsíci

    Great vid I just got one ,,But mine cuts without the ground clamp I wanted to know what the ground clamp is for ? Its a non touch cutter

    • @DIYMyWay
      @DIYMyWay  Před 3 měsíci +1

      Thanks! For one thing, the ground clamp protects you from accidentally becoming the return path for the current and, while the pilot arc circuit can start and maintain the plasma stream, I don’t think it is designed to carry the full current of cutting. Having the material that you’re cutting be the return path should result in a better cut.

    • @DELTRANIO99
      @DELTRANIO99 Před 3 měsíci

      @@DIYMyWay Thin sheet metal it cuts with no clamp & seems fine ,,But once I put the clamp on it ,,It starts a second and stops cutting

    • @DIYMyWay
      @DIYMyWay  Před 3 měsíci

      @DELTRANIO99 That’s odd!

    • @DELTRANIO99
      @DELTRANIO99 Před 3 měsíci

      @@DIYMyWay Thats what I thought LOL

  • @DMHRC
    @DMHRC Před 11 měsíci

    Hello! It's been a few months, have you had any major trouble using the Vevor yet? I'm repairing an old brush hog I picked up cheap and am considering a plasma cutter for the job. Thanks!

    • @DIYMyWay
      @DIYMyWay  Před 11 měsíci +1

      Not at all so far. Recently I had to cut some 1/8” aluminum which was the first time I’d tried it on aluminum and it cut through it like it wasn’t even there. A plasma cutter should be able to easily cut the thickness of steel used on a brush hog, plus I’ll bet you’ll find other uses for it too. Good luck and thanks for watching!

    • @DMHRC
      @DMHRC Před 11 měsíci

      @DIYMyWay Thanks for the quick reply! I really enjoy your videos. After a miserably hot week, I'm drinking coffee and rewatching your brush hog and remote ssqa coupler videos this morning. The finance dept. manager may get upset with you 😆 Happy tractoring!

  • @jjoop
    @jjoop Před 6 měsíci

    Mine didnt have the 2 studs on the back of it

    • @DIYMyWay
      @DIYMyWay  Před 6 měsíci

      That’s a bummer! Thanks for watching!

  • @edking4344
    @edking4344 Před rokem +1

    Your running it with the pressure to low. You want to go 0.5 mpa/70psi minimum. Your technique looks fine.

  • @Vaz_DeFerenz
    @Vaz_DeFerenz Před 8 měsíci +1

    why would you not just get different hose/fittings and a different gauge for the regulator? easy

    • @DIYMyWay
      @DIYMyWay  Před 8 měsíci

      Because I didn’t. That’s why. Besides, another company is sending me a better plasma cutter to try that doesn’t have the shortcomings of this one. Thanks for watching!

  • @MrVinor44
    @MrVinor44 Před rokem

    What made you decide on the Vevor?

    • @DIYMyWay
      @DIYMyWay  Před rokem +1

      Because Vevor offered to give it to me in exchange for making the video. Thanks for watching!

    • @seanseoltoir
      @seanseoltoir Před rokem

      @@DIYMyWay -- That's actually surprising, considering the total number of subscribers that you have... I wonder if they are going to be sending you a 1099 form at the end of the year since that technically counts as "income" as far as the jackbooted thugs at the IRS would be concerned... Did they ask for your tax ID?

  • @inthedarkwoods2022
    @inthedarkwoods2022 Před rokem +1

    Good review. Looks like a cutter to avoid

    • @DIYMyWay
      @DIYMyWay  Před rokem

      Thanks! Not what I would choose but for a freebie, it’ll do just fine.

  • @ParaisoSensorial
    @ParaisoSensorial Před rokem +1

    Excellent video.
    New friend here.🔔
    You have a fantastic channel.
    Have a good weekend. 💚170

  • @brokenrecord3523
    @brokenrecord3523 Před 5 měsíci

    Vevor's marketing model seems to be to give away product to any CZcams channel with more than a thousand subscribers.
    I'm not accusing anyone of fudging the review, but the conflict of interest can't be ignored.

  • @seanseoltoir
    @seanseoltoir Před rokem +1

    Pressure gauge in kg/sq-in? LMAO... They can't decide if they want to do metric or US customary units?
    EDITED: At the 7m07s point, you show the pressure gauge and if I use a magnifying glass to enlarge it (old eyes), I see that it is in kg/sq-cm which is a more expected unit of measurement for something coming from a metric country... :) It is also a unit of measurement that someone from the US could convert from by just remembering a couple of conversion factors instead of needing a unit conversion calculator...
    2.54 cm/in and approx 2.2 lbs/kg...
    1 kg/sq-cm = 2.2 lbs / sq-cm = 2.2 lbs * 2.54 cm/in * 2.54 cm/in / sq-cm = appox 14.2 lbs/sq-in
    Plugging that into the 45 psi that you were trying to achieve at 7m13s -- 45 / 14.2 = 3.17 kg/sq-cm which looks extremely close to what you set your regulator at... Of course, I rounded a lot here, but considering the accuracy of one of those types of gauges, it won't make a difference... :)

  • @RCAFpolarexpress
    @RCAFpolarexpress Před rokem +1

    Bonsoir Sir 👍😇👌 ( I WAS REALY WAITING FOR YOUR VIDEO 🧐👍) Great Tele transportation plasma cutter Sir 😇👍 Ho LA LA, I do not like that snake 16 feet long Sir 🥴🤣👍 Yes why they did not make the same length of the torch ?? 16 feet long, I guess you have to make an extension ground cable 😇👍👌 OUTSTANDING FIELD TESTING CUTHING Sir 👌👍🧐 That is very nice modification on air supply 🧐👍💪 Slow win the race 👍🧐👌 Yes like in many things, practice does make perfect Sir 😇👌👍 That is an OUTSTANDING Plasma Cutting Video Sir Cheers👍✨🚀😇🍻

    • @DIYMyWay
      @DIYMyWay  Před rokem

      Bonsoir Dave! Merci! Yeah, a 16’ snake would be cause for concern! The short ground cable was disappointing, but looks like it uses a standard connector so I could get a longer one, or an extension cable as you suggest. The leaking air hose was aggravating but hopefully fixed for good now. Thanks for watching! Cheers!

  • @richardkelleher1711
    @richardkelleher1711 Před rokem

    For a cleaner cutting experience, check out the plasma cutting bench extension video from Mike Festevia. Simple design that attaches to the side of your welding table. Water bath collects most messy bits.

    • @DIYMyWay
      @DIYMyWay  Před rokem

      Someone else mentioned that video also and I plan to check it out. Thanks for the tip and for watching!

  • @SquirrelsForAll
    @SquirrelsForAll Před rokem

    I have this machine and it's actually not very good. I regret not purchasing a USA produced Hypertherm. This Vevor machine is a fussy nightmare and yep, I had many problems with the poor quality air hose.

    • @DIYMyWay
      @DIYMyWay  Před rokem

      Sorry to hear that! I haven’t used mine much but it has done what I needed it to do. And since it was given to me in exchange for a video review, I can’t complain. Thanks for watching!

  • @bray7197
    @bray7197 Před rokem

    why would anyone use this on 110?

    • @DIYMyWay
      @DIYMyWay  Před rokem

      That’s easy. They’d use it if 220V wasn’t available and they only needed to cut thin metal. Thanks for watching!