"Keep Warm & Save Energy: "Retrofit Rubber Draught Excluders & Weather Seals for Cozy Interiors"

0.:00 Retrofitting Draught Excluders (Indoor Weather & Interior Surround/Around Door Seals)
0:19 Outdoor Exterior Garage Door
0:23 Exitex Rain deflector Bar Aluminium (20 Weather Board Drip Door)
0:40 Weather Deflecting end caps
0:50 Door Purpose (Inward facing Vs. Outdoor)
0:60 Exitex Low Height Threshold (Inward) MDS80 (Exterior)
1:10 Rear Thermal Barrier (Exterior)
1:20 Other Attributes (Rear Thermal Barrier)
1:56 Rain Deflector & Threshold Benefits
2:20 Draught Excluders (Deflector & Threshold) Vs. Fit for Purpose
2:45 Draught Excluders Benefits
3:10 Draught Excluder Types
3:27 Draught Excluder Installation (Interior Door)
3:32 Storm Guard Heavy Duty (Around Door) Seal Aluminium (Interior Doors)
3:48 Garage Door Rubber Seal (Interior /Exterior)
3:50 Open Storm Guard & Garage Seals Packaging
3:56 Garage Seal Parts List & Door Locus
4:20 Storm Guard Parts List & Door Locus
5:00 Storm Guard Straight & Curved Rubber
5:08 Curved Rubber Vs. Hinges Locus
5:13 Straight Rubber Vs. Strike Plate/Top Locus
5:18 Rubber profile orientation
5:30 Door Measurements & Seal Cut Tool Selection
5:40 Hack Saw Tool Selection (TPI)
6:07 Interior Door Draught Benefits
6:23 Thinner Vs Thicker Aluminium Hack Saw Selection
7:57 Tool Kit for Draught Aluminium Cut & Assembly
8:20 Measure Interior Door Lengths, Sides & Top
8:27 Determine Interior Door Purpose & Draft Assembly Locus
9:22 Measure Top Inside Width & Door Side Lengths
10:08 Repeat & Reproduce Door Measurements (From Correct Locus)
10:15 Cut Surround/Around Aluminium w.r.t to Door Size
11:40 Cut inside width of Door Frame from Aluminium Bar - STEP1
11:50 Dislodge Aluminium Bar & Cut excess Rubber
12:00 Slave Flush Cut Aluminium Bar Rubber to Door Top Side
12:30 Check Top Thick Part of Aluminium (4mm from Door Surface)
12:40 Mark up Slave Hole Positions
12:50 Select Drill bits & Screws
13:35 Pilot Drill & Open up Final size Holes on Door Top Side
13:52 Screw Aluminium Bar seal to Door Top Side
14:22 Test Door Top Side Assembly for Door Flush
14:38 Assemble Side Door Aluminium Seals
14:41 Determine Locus for Straight & Curved Rubber on Door Sides
15:00 Aluminium Bar Notch Cut Side Door Assembly (Straight R)
15:40 Repeat & Reproduce Aluminium Bar Cut - STEP2
16:28 Cut Notch from Side Aluminium Bar
17:30 Assemble Straight Rubber Aluminium Notch Bar to Side Door
17:50 Cut Straight Rubber Al Notch Bar to fit Side Door Length
18:30 Cut Rubber Excess off to Match Al Notch Bar
18:40 Line up Straight Top Seal with Side Door Seal (Strike Plate Locus)
18:45 Pilot Drill Side Seal at right angles flush with Top Seal
18:50 Screw Side Seal at right angles flush with Top Seal
19:20 Aluminium Bar Notch Cut Side Door Assembly (Curved R)
19:25 Cut Notch from Side Aluminium Bar
20:20 Repeat & Reproduce Aluminium Bar Cut - STEP3
20:12 Cut Curved Rubber Al Notch Bar to fit Side Door Length
20:40 Cut Rubber Excess off to Match Al Notch Bar
20:49 Line up Curved Side Door Seal with Top Seal (Hinge Locus)
21:18 Markup, Pilot Drill Side Seal at right angles flush with Top Seal (Hinge Locus)
21:23 Final Size Drill & Screw Side Seal at right angles flush with Top Seal
21:30 Test Door Top Side Assembly & Hinge Side Seal for Efficient Seal
21:37 Storm Guard Heavy Duty Garage Door Assembly
21:50 Measure Door Bottom Width & Gap
22:20 Cut Excess Rubber in line with Door Bottom Al Bar
22:39 Line up & Mark up Al Bar on Door Bottom
22:50 Pilot, Final Size Hole positions on Door Bottom Al Seal
23:00 Assemble & Screw Aluminium Seal to Door Bottom
23:10 Pinch & apply Industrial Glue & Locktite to Al Seal Edges (Optional)
23:50 Reassemble after Pinch Application
23:55 Test installation Assembly
24:10 Repeat Cut, Line up, Markup for Adjacent side of Door Bottom Al Seal
24:31 Repeat Pilot, Final size Drill & Screw Install for Adjacent side of Door Bottom Al Seal
24:45 Adjacent Side Door Bottom Al Seal excess length Bottleneck & Safety Hazard
24:54 Corrective action :Al Seal excess length Bottleneck & Safety Hazard
26:17 Opening more Holes on Aluminium Strip
26:28 Pilot & Opening Final Hole Sizes (Round & Oval Holes)
Useful links
"Quick Fix: How to Tighten a Loose Hacksaw Wing Nut & Replace the Blade" - Hacksaw Maintenance
• "Quick Fix: How to Tig...
"Quick & Easy DIY Hacks: Perfectly Cut & Drill Aluminium Rubber Seal Draught Excluder Strips"
• "Quick & Easy DIY Hack...
"Soundproof: Sealing Studio Doors with Rubber Draught Excluders" - DIY Acoustic & Thermal Insulation
• "Soundproof: Sealing S...
"Soundproof & Insulate: Seal Your Door with Rubber Draught Excluders for Perfect Acoustic Insulation
• "Soundproof & Insulate...
"Keep Warm & Save Energy: "Retrofit Rubber Draught Excluders & Weather Seals for Cozy Interiors"
• "Keep Warm & Save Ener...
"Quick & Easy: Removing and Replacing a Door Handle (Lever on Rose)" - Step-by-Step Guide
• "Quick & Easy: Removin...
"Top Tips to Avoid Electrocution & Perfectly Hang Picture Frames - DIY Safety Guide
• Hang Picture Frames Li...