Cheers ! Your efforts to make this video, and its quality, simplicity, clarity made it possible for me to complete a project...I could not quite figure out how to lay out the cone....you saved the day ! THANKS
Thank You for the excellent explanation! I created a cone with a 24 inch base, 10 inch height, 1 1/2 top opening. While the drawing turned out considerably larger than yours because of the larger dimensions, the pattern turned out perfect using your method and instructions.
Thank you for sharing your video is the first one I watched. I want to make the shape of a cone out of metal for a project I started, but realised I have to make a cone shape first out of sheet metal.
If you draw a half circle at the base, that same divider distance will then divide a quarter of that circle into three even spaces which makes it twelve for an exact pattern. Good vid.
I think I understand how you do this cone layout. How do you determine the right length of the shaped segment without overlapping the two ends? Much thanks.
Hi, I'm a bit confused, making a cone shape, but a low cone lets say a flat view of 300mm diameter across the top and 352mm diameter across the bottom, I do the sweep with a compass to get the arc, once I do the calculation of 3.14 x 352 = 1,105.28 when cut out and joined the diameter at the bottom of the cone is way too short, what am i doing wrong?
Cheers ! Your efforts to make this video, and its quality, simplicity, clarity made it possible for me to complete a project...I could not quite figure out how to lay out the cone....you saved the day !
THANKS
As a fabricator, its a very big help.. thank you...
Thank You for the excellent explanation! I created a cone with a 24 inch base, 10 inch height, 1 1/2 top opening. While the drawing turned out considerably larger than yours because of the larger dimensions, the pattern turned out perfect using your method and instructions.
Thank you for sharing your video is the first one I watched. I want to make the shape of a cone out of metal for a project I started, but realised I have to make a cone shape first out of sheet metal.
You are a teacher very rare see you on the job
You didn’t show us the calculations for the diameter
If you draw a half circle at the base, that same divider distance will then divide a quarter of that circle into three even spaces which makes it twelve for an exact pattern. Good vid.
Great,As a fabricator,I am very interested of your video,thank you
Great. Best part is its said and shown so simply CHEERS
Very nice thank you for sharing!
I just used your method, for duct reducer, thank you
Nice an easy, Thanks!!
this was filmed and explained very well
thank you
I think I understand how you do this cone layout. How do you determine the right length of the shaped segment without overlapping the two ends? Much thanks.
There are SO many tutorials of how to draw the cone but how about how to actually make a fine cone.
tenks m8 good job
Where the rest will you be making a video of the cone be created to actual metal?
Sir. How to put marking of 5 ltr, 10 ltr, 15 ltr in 20 ltr frustrum shape bucket? Is there any formula ?
Nice
Right on.
Thankyou 👍
How to template an ellipse cone?
Hi, I'm a bit confused, making a cone shape, but a low cone lets say a flat view of 300mm diameter across the top and 352mm diameter across the bottom, I do the sweep with a compass to get the arc, once I do the calculation of 3.14 x 352 = 1,105.28 when cut out and joined the diameter at the bottom of the cone is way too short, what am i doing wrong?
Forgot to say on the flat plan view the height is 50mm
That knife position makes me uncomfortable every time his hand moves
How about large diameter pipe cone sir, example. 2.5 m. x 1.0 m Wide. Is it same procedure to lay it out in large steel plate?
How do you determine the height
Draw cone profile that you want
My mother tongue is telugu therefore
I want telugu language plz sir...
Blah blah sniff, blah blah sniff sniff..
Dislike.