TRAILER HUBS AND WHEEL BEARING REPLACEMENT GUIDE
Vložit
- čas přidán 28. 05. 2024
- Seat and adjust trailer wheel bearings easily. Replace wheel bearings easily in this tutorial. Trailer wheel bearing inspection & repacking intervals. Inspect and identify bad trailer wheel bearings visually and by using the shake and spin test. Inspect bad trailer wheel bearings by removal also. Replace trailer wheel bearings and pack grease the easy and complete way. Learn how to measure and order trailer wheel bearings and trailer wheel hubs easily. All trailer wheel bearings use what is called, a single nut manually adjusted bearing system. It is easy to work on overall and many repairs can be done at home.
*if I have helped you out-please consider tipping me with the "Thanks" button 😃
Video Parts ✅
1" bearing kit: amzn.to/3skZO3c
1/16" 1-3/8" kit: amzn.to/3e3dzv8
1-1/4" 1-3/4" kit: amzn.to/3mkWAZF
4-bolt hub kit: amzn.to/3J5bTzB
4-bolt galvanized: amzn.to/3mdcAwT
5-bolt hub kit: amzn.to/3J24IIa
5-bolt galvanized: amzn.to/3yEwGoO
6-bolt hub kit: amzn.to/3pcaQpi
8-bolt hub kit: amzn.to/3Eaf851
1" spindle: amzn.to/3q8x8rw
3500# ez lub spindle: amzn.to/3e5YI2T
spare assy. mount: amzn.to/3EhyzJm
grease seals: amzn.to/32dHk9Q
repair sleeve kit: amzn.to/3FfT4r8
1.98" dust cap: amzn.to/32dHmhY
2.44" dust cap: amzn.to/33JsyIL
rubber cap plugs: amzn.to/3yEBUAI
#2 lucas tube: amzn.to/3mi5jvU
#2 lucas tub: amzn.to/32bHzSN
cotter keys: amzn.to/3J6BA2O
locking retainer: amzn.to/3e4GcIn
spindle nut clip: amzn.to/3p8kCsz
brake shoe kit: amzn.to/30H6s8B
electric puck kit: amzn.to/3q4g5Xw
brake complete kit: amzn.to/3qa5UAH
disc brake kit: amzn.to/3mkZcGX
shop towels: amzn.to/3Fd4EmO
brake clean: amzn.to/3q8cQ1e
emery cloth kit: amzn.to/32e92U9
1.98" buddies: amzn.to/33HVDUW
2.047" buddies: amzn.to/3qa8fvt
2.441" buddies: amzn.to/3Fe4ATA
4-lug tire/wheel: amzn.to/32jtkex
5-lug tire/wheel: amzn.to/3qbHyqo
6-lug tire/wheel: amzn.to/3E7wUWt
8-lug tire/wheel: amzn.to/3E7wXl7
1/2" torque wrench: amzn.to/3qgzMvf
Video tools ✅
My dogs favorite toy: amzn.to/3ZlfEZl
tire chocks: amzn.to/3mkddoh
uni-jack 4k#: amzn.to/3sgsuu3
uni-jack 6k#: amzn.to/3e4H9QX
bottle jack 10ton: amzn.to/3yEmNrf
bottle jack 20ton: amzn.to/3p9OViN
jack 3k#: amzn.to/3GUTZNP
floor jack 7k#: amzn.to/3yNJbhN
emergency jack: amzn.to/3E7vVWh
3-ton stands: amzn.to/324969d
6-ton stands: amzn.to/3E8Nbuj
4-way wrench: amzn.to/3q8B2Rc
Milwaukee 1/2": amzn.to/3J29NQK
Milwaukee 1/2": amzn.to/3e8e9aQ
Milwaukee combo: amzn.to/3EbjqJh
bearing packer: amzn.to/3E5egyF
grease gun tool: amzn.to/3GXpnLL
dial caliper: amzn.to/30LUieI
tape measure: amzn.to/32jhdy5
brass punch set: amzn.to/3yIZ0Gl
steel punch set: amzn.to/3E4MRwE
BIG RACE punch: amzn.to/3Qbbd0t
seal install kit: amzn.to/3pb4mqS
Stanley hammer: amzn.to/3yHZywv
dust cap tool: amzn.to/3pa21wv
seal removal tool: amzn.to/3q2Rdzq
claw hammer: amzn.to/3ed41NX
pry bar set: amzn.to/32aUftt
screwdriver set: amzn.to/32aY0z8
Some favorite tools ✅
Wireless Chassis EAR: amzn.to/3n3EkaQ
Quiet Bands: amzn.to/2Lr3CKo
Headlamp: amzn.to/2LskvEG
Hub shocker: amzn.to/2Q2b0jO
Power Probe: amzn.to/2NTyaGg
Hydraulic flare kit: amzn.to/2N8Ijzg
Antivibe hammer: amzn.to/2N8W8ho
Pry bars: amzn.to/307BL6b
knuckle savers: amzn.to/2LnkfGS
Spark plug sockets: amzn.to/2N7dnzB
Hose tool: amzn.to/2LoD649
Chassis Ears: amzn.to/2Ltl1SD
Soap: amzn.to/332qyWd
My dogs favorite toy: amzn.to/36irgRl
Auto repair for dummies: amzn.to/3FcUZg0
Ultimate wheel bearing removal tool ✅
Hub Shocker: • HUB SHOCKER HUB BUSTER...
Support the channel and grab some swag ✅
EF-Merch: teespring.com/stores/easy-fix...
Thanks for being here. Your time is valuable.
~Shaun 🔧
0:00:00 single nut manually adjusted
0:01:22 service interval
0:01:03 cheap insurance
0:01:39 broken trailers
0:02:30 visual inspection
0:05:15 Shake and Spin test
0:05:25 safety
0:06:49 Shake and Spin test
0:08:00 bad bearing sounds
0:08:48 removal and inspection
0:23:53 measure and order parts
0:28:28 grease
0:33:14 install bearing races
0:42:43 pack wheel bearings
0:51:53 seating and adjustment
1:00:55 assembly
Easy Fix is a participant in the Amazon Services LLC Associates Program, a program designed to provide a means to earn advertising fees by linking to amazon.com
If you purchase from affiliate links I will get a small commission with no extra cost to you. This helps me to make more videos. Thank you! - Auta a dopravní prostředky
That was great! Clear shots no tacky jokes or distracting background music. Perfect instructional video
Thanks i am glad you enjoyed it. A lot of work went into it. Really appreciate 😀🔧
2nd. Best bearing tutorial... Last video I clicked guy mentions halfway it's his first time doing the job. Lol
@@user-lv3th9pe7u Thank you! Not my first. I should have mentioned it 😃
But it is a long drawn out comment lol. 🏴 just had to . Laugh with me. Lol
An absolute “Masterclass” in wheels bearings…thanks!
Wow thank you!! What was your favorite section?
No questions yet but I have to say, Thank you for going right into the information without a 5 minute intro about your life and dreams. This is exactly what I was looking for.
My pleasure! 😃😃
Bro told you thanks for the info. I simply don’t care about you. 😂
@@MrReyes-bq1xh Well, we didn't search celebrities did we? Searched to learn. Not a life event. 😂
Certainly the most comprehensive review on the 'net, raising the bar for what's out there.
Ha! Thanks man. I really appreciate that 😀🔧
The best video I've seen and the most professional. one step I noticed that he missed was when using the grease gun on the spindle was he forgot to rotate the wheel while applying grease to fill the cavity. otherwise the best one I've seen yet.
Thanks a lot! Glad to help. Rotating the wheel during greasing could help for sure 😀🔧
I've looked at a dozen boat trailer vids for this simple job. Yours is by far the best filmed for visibility and lighting. The best for start to finish parts. Not just verbal instructions which aggravate the crap out of me when I'm looking at hey a VIDEO?? THAT MEANS VISUAL. lol thanks for showing each step!! I did mine and actually split the metal hub bearing chamber right down the middle knocking the race out w a flat screw driver. I knew I should have used a brass punch but I didn't have one so I tried to use the screwdriver. But to have actually split that cast metal I figured I might better just go for new hubs so I bought new hubs and bearings all the way around. Thank you so much for your great video
Thank you!! Really appreciate that and I am glad I could help out 😃🔧
I am going to attempt this tomorrow morning for the first time. I have been watching dozens of videos, but this has been the most detailed and frankly the cleanest. You're in no hurry and it shows the attention to detail that you display. It's going on my Favorites.
Excellent! Glad to be of service, I hope your project goes well! A clean space really does help. Sometimes little things like that make everything easier 😃😃
Quite superb, I’ve fiddled with many boat trailers for over 50 years and I learnt more about fitting bearings from this excellent video than I ever knew before, thanks so much for putting this up.
Great to hear! You have a lot of experience! No problem, glad I could help out 😃🔧
Not sure if you're aware that those bearing race drivers are designed to be used with the taper facing the finished surface to help "self center" the driver in the race while installing them. The taper never touches the finished surface but is supposed to guide at the very top of the race and then taper "away" as the diameter decreases. Otherwise, there would be no lip or taper on the driver, it would just be a piece of round stock with squared ends and a hole in the middle. As machinist, I have custom machined these drivers for many years and are invaluable when installing bearing races, especially large ones using a hydraulic press. Really loved the video, you covered all the important aspects in a detailed fashion which seems rare these days on CZcams videos. Well done!
Thanks! You are correct. Over the years i have had trouble with the correct fitment like you are suggesting. I have had them not sit flush and rock on me when installing like intended. The default position is to flip them over and use the flat side. I am so used to it i forgot to even try it or mention it. Autopilot haha. My bad. Im glad you enjoyed it! Thank you for the nice comment😀🔧
Great video, very detailed explanation. Thank you!
Do you think he packs to much grease in hub? Most videos I see use far less. They definitely put it everywhere, but if this is how it's done then I haven't been using enough in fear of "too much is as bad as too little."
I learned alot of helpful information from your video only thing I would have added would be some anti seize to lug studs I noticed you used it on your brake areas but thank you for the tips
Thank you! Very happy to help 😃😃@@IdleDrummer
The absolute BEST tutorial I’ve seen on hub/bearing maintenance and replacement. Outstanding detail and explanations. Thanks!
Wow! Made my day, thank you 😃😃
The best video on trailer axles on CZcams hands down!!!!!!!.. excellent demonstration now I understand how to properly maintain and service my trailer bearings thank you thank you great tutorial
Wow, thank you! I really appreciate that. What was the best part or section for you?
This is absolutely my favorite video for diagnostic and service. Thank you!
Glad it was helpful! It is a long video, I think some people are looking for shorter. But, I tried to include most things where I needed help long ago myself 😃🔧
Excellent detailed explanation! I always service the wheel bearings on a newly purchased trailer. That 20 minutes can save several hours on the side of the road!
Thanks man! That is a really great tip! Rather than assume the trailer is good when new, double checking is a brilliant😃🔧
This has been the most detailed video I have ever seen on packing bearings replacing races fantastic video thank you very much
Wow, thanks! Glad to help out. Good luck with your project 😃🔧
And THIS is how I made sure my trailer was safe enough for a long road trip. Thank you! 😎🙌
Excellent. Glad to help, safe travels 😃🔧
This video is fantastic. Ten days ago I was pulling my 21’ Bayliner Bowrider on a single axle Escort trailer out of her garage and backing her up to wash and prep her for the seventy mile drive to the lake. While backing up my wife screams your right wheel is falling off. I thought she meant my wheel was off in the grass. I got out to see that my right wheel was indeed coming off the the axle. I admit I haven’t serviced my bearings for over twenty years. I had no idea because I only put my my trailer in fresh water twice a year. Got two bearing kits from my local marine shop and in the process of rebuilding both wheels. Interesting, because I’m figuring out that I’m on my own. Don’t have anything like AAA for trailers with a 3000 pounds boat on it. Good thing is that this happened right in my driveway and not on the road. Thanks for this video. I also have a six stud hub.
Thank you!! I really appreciate that and I hope you are able to get it all fixed up! Trailers are really simple, basic, and last a long time if maintained. I have seen the bearings outlast the trailer many times when they have been checked, adjusted, and greased periodically. It is easy forget about maintaining them for everyone. Happens to me sometimes too. If they break on the road it can be an extreme hassle. Trailers do a lot of good work hauling all sorts of loads 😃😃
Outstanding video, done my boat trailer today and the difference just pushing it around the yard was staggering, thank you, from Australia,,,,
No way that is awsome! Glad it helped 😃😃
This was a very well done maintenance tutorial for us new trailer owners. Thank you
Thank you for your kind comment I am so glad it was helpful! I love trailers! I hope you get many miles and years out of your trailer 😃🔧
This is the best trailer bearing video on CZcams. They should put this on boost so you can retire. Thank you!
Thanks Scott! Really appreciate that 😀😀
A good video.
I learned bearing replacement and field repair from my Dad.
He was a tool and diemaker and machine tool maker for 50 years.
He made more tools than He bought. I even watched him weld, field braize and grind round spindles and tractor PTO shafts and re-temper them.
I often use a brass punch, block of wood and wood dowel. Unless the races and seals are stubborn, it prevents me from damaging my work.
I have always done the 1/4 turn method.
For my trailers, I re- adjust after the first use. Every stop while pulling, we check the temperature of the rims.
You should be able to touch without burning your hand.
I more recently keep my work laser thermometer In my driver door pouch.
Thanks a lot. That is a great story about learning from your Dad. Great tips 😃😃
What temp do you look for on the laser thermometer? my hubs get warm to the touch not hot. That’s on an hour driving at 60 miles an hour and a sunny day.
Talk about the best trailer brake video on the internet, thank you
Thank you! No problem glad to help 😃😃
Awesome detail. Loved the step by step, and the exploded view of the spindle and parts. Thank
you.
Awsome! No problem I'm glad you liked it so much. I like looking up spindle parts! It was fun making it 😀🔧
Well done! Clear, concise, thorough and GREAT video quality. I have had trailer bearing failures many times . Now I know why. Many thanks.
Thanks! I got a new camera and this was the first video I used it on. I am so glad you liked it 😃🔧
I think that was the best video on bearings I have seen.. GREAT JOB!
Wow, thanks! I really appreciate that 😃😃🍻
That was a great, detailed, instructional video. I came specifically for the hub install section, no one else I've seen actually goes over bearing pre-load. Thanks sir.
Excellent! Glad to help 😃
I just did the super thanks but I must tell you that your video was incredibly helpful I just welded two axles to my 20-foot container and installed electric brakes and hubs, just as you had directed. It was exactly as you had described--no surprises. I can't thank you enough for such a well-done video. Mahalo for your time.
Thank you! I really appreciate that. I am so glad it helped you out 😃😃🔧
I was always taught to back off the nut 1/6th turn. The system heats up and expands.
You don't want to squeege the grease away from the rollers. ,
Dude, you’ll never get views without some corny rave music or stupid jokes! Lol. All jokes aside, there are a lot of people that could learn a lot from you. This has been the most helpful video and I haven’t even started my project yet. Even though I’ll be doing this on a camper, you have been extremely helpful. Well done!
Wow! Thank you. I hope your project goes well 😀🔧
I thought this video was going to having multi millions of views when's I checked. Thanks for making video great job!
Thank you! I am glad you liked it 😃🔧✅
Amazing and very detailed explanation of proper bearing replacement. Thanks for the hard and detailed work.
Thank you! I am so glad it has helped you out! Also thank you so much for your time, the view, and comment 😃😃
Great job man, as a mechanic for over 20yrs watching a video on tapered roller bearing checking, cleaning, replacement, seating and bearing adjustment is only out of curiosity to see other ways of doing it than I do.
But you covered to 2 only ways to do it properly with excepting to actually measuring bearing clearance.
It’s simple you use a magnetic or vice grip style dial indicator base and a indicator that reads less than one thousands of an inch.
That is the only real way to measure zero bearing endplay, the typically most bearing manufactures have a spec of 0.000” - 0.002” for long bearing life and operation!
By the way cotter keys don’t get bent over the case nut, I’m every class, recertification or training course they are bent one to the left and right going around the castle but.
The cotter key is more likely to shear if it is bent over the nut versus around the nut, I’ve seen it and it’s easy to tell which way the cotter key was bent after it failed!
Great tips! Really appreciate your knowledge 😃🔧
This is a great example of thorough and professional treatment of a subject (any subject). The thoroughness was of crucial importance to me when it came to the seal surfaces and options for dealing with those-options that were not discussed in the more cursory and less professional videos I watched before finally getting to this one. Thanks very much & see you on the road.
Thank you I am so glad you liked it! It took a while to make but I was hoping for this exact response. Much appreciated!! 😃🔧
This is 100% of the information I needed to fix my old Dayton Fayette axle problems on an old used trailer. Pretty sure replacing the grease and all hadn't been done in decades. Thank you!
Oh wow! Many trailers receive the same treatment. Kinda crazy 😀
Phenominal detailed video. Did an axle today with the pops for the 1st time using this video. Absolutely perfect video. Thank you.
That sounds nice! I am glad you got your project sorted out 😃😃
Very detailed explanation and demonstration! Probably the best I have eve seen! Thanks for your time and efforts!
Thank you! I am so glad you liked it. A lot of effort was spent 😀🔧
@@EasyFixShaun I just watched it again! You are so thorough! Amazing!
@@thebeardedstork432 Thank you again!! I put lots of easter eggs of info in the video 😃
Excellent job!!! I have seen many a fishing trip canceled because some moron didn’t take care of their bearings (or fail to check tires, hubs, and pressure). You delivered an impressive amount of info.
I always have a greased and seated spare hub with me for whatever trailer I happen to be towing. I build a spare when I am redoing the bearings. Once I seat the new bearings in the spare, I add a spare washer, castle nut, and cotter pin and vacuum seal it all together (seal-a-meal style). Bearing failures sometimes result in losing the entire wheel, as in it comes completely off of trailer… The hardware is usually lost in those instances… (sometimes a wheel lug nut is the same size and thread pattern, but that is pretty rare). Better to limp it home or continue on with the right parts (and not have to leave it on the side of the road, and then return with what you should have already had with you).
Thanks I'm glad you liked it. That spare in a bag is a great idea! Thanks for sharing😀😀
I use the brass punches so it don’t nick up my hub or race. Good video.
great tip! 😃😃
Buying you a coffee for your incredibly detailed and useful video.
Thank you!! Glad it was helpful! I really appreciate that so much 😃😃
By far, the best trailer wheel bearing breakdown video. Incredible work!
Thanks! Appreciate you too! 😃
This is the next best thing to watching a buddy who knows tons about bearings and is an excellent video to watch in preparation of doing this maintenance. Thanks.
A couple thoughts: 1) once you get to the point of reassembling we want to be careful about keeping contaminants out of the bearing stack up. At 49:00 all the banging and wood work knocks all sorts of goobers into the grease which can eventually end up in the bearing. I think at least cover the seal with a lint free towel when banging the seal back in to prevent that. I also like to use paper towel when cleaning out the grease and then switch to lint free (blue papers) when I reassemble so as to not contaminate the grease with lint. 2) When using the zerk fitting you should continually spin the hub while pumping grease. The spinning helps the grease flow thru the return path back to the front. If you don't spin the hub there is a chance you can build up pressure at the inside bearing and blow past your grease seal into the hub area.
Good tips thank you 😃
Great work! There is a Huge contrast to most of the other videos on this topic where advice is given based on what they heard for others; some totally wrong. The difference you have shown is the understanding of how the components and assemblies work together. You really went above and beyond.
Wow! Thank you so much! I really put a lot of effort into the video and i can't tell you how happy i am that so many of you find it useful. Thank you 😀😀😀
@@stevetrepanier4351 Thanks Steve, all good technical info. Rtv isn't needed, seals are press fit and seal automatically. It wouldn't hurt anything to do that though. It is an extra step and not commonly done in the field.
Clean parts and grease is also a great idea!
Bearing adjustment is very important. Zero end play is the goal. Although with the cotter key system perfect adjustment can be hard to attain. With that in mind these bearing styles are extremely old and archaic but they work very very well 😃🔧
Very nice video. I cool outer races in the freezer before tapping them in.
That's a great tip. I never do it, but I should try it 😀
Thanks for the video bud. Very informative!!
No problem! Glad to help. Sorry for the delay. Take care 😀😀
This video was awesome, thank you for sharing !!!.
Thank you! Glad to help 😃😃
Very good video! This can lead most anyone to a victory when replacing trailer bearings. 👍
Wow thank you! Really appreciate 😃😃
Very well done sir. Going to try this for the first time this weekend. I feel much more confident after watching this. Thank you!
Excellent! No problem, glad to help. Good luck on your project this weekend 😀😀
Thank you!!! This was incredibly helpful, and I especially appreciated the measurements info 🙏
Holy Toledo! Thank you 😊😊
Awesome video! Thanks for taking your time to film this. Super helpful!
Yes! Thanks for commenting. It was a fun one to make 😃
Awesome video, you explained everything to perfection, Thanks for posting!
I really appreciate your kind words! Glad to help out 😃😃
Thank you so much for this excellent instructional video!!! (I greatly appreciate your calm demeanor with no profanity.) May God Bless you and your family< John 3:16
You are most welcome. Thank you! I am glad you liked it 😃😃
Excellent detailed video! Thanks for all your time and effort producing this! I especially liked how you gave tool options, different approaches and even knocked down the audio volume when you were hammering. One of THE best videos on this topic on YT. I've done a few trailers many years ago, but now have both a boat and RV trailer to maintain and will feel confident doing my own work. Thanks again!
My pleasure thank you so much for your comment 😃😃
This was absolutely amazing.....thank you so much for sharing !!!.
Thank you! Im so glad you liked it 😀😀😀
Best bearing video on the internet
Thank you!! What was the best section for you?
@@EasyFixShaun The whole video is great. As a mechanical engineer I very much appreciated the mechanics how the bearings work and then graphs, axis, and link examples overlayed the video. It's very good for beginners to understand how they work to avoid damaging the components during disassembly.
As an aspiring content creator I really appreciate the camera angles you were able to get of the actual work. For example the interior shots of where to hit the race to knock it out, there's no space to do but let alone do it and film it? Awesome! I know it takes about 4 times the amount of time to document your work. So I definitely appreciate it. Keep up work like this.
Wow thanks man! Many angles were a huge challenge for the video. But I was pleased with the product in the end so it was worth it. It's hard making videos. Good luck on your journey 😃😃
Just one thing i do a little different, Dexter recommends that you spin the wheel/hub while pumping the grease in through the hole in axle so you don't blow out the rear seal.
Not a bad Idea at all! Great tip! Thank you for mentioning it for sure. This was just personal preference. I have found that pressure overcomes space and the spaces are filled by grease with or with out spinning. I haven't yet blown out a seal from greasing. I do spin sometimes also during greasing. I just have never seen any difference, the grease seems to fill the void either way 😃
Bearings are a little tight. Should be .001" - .005" end play on bearings running on grease. You can sand the washer to get a little more clearance. You must spin the wheel when adding grease to an EZ Lube system.
Good points for sure! I would add that .001.-.005 is hard to measure sometimes with a hub full of sticky grease. The hand adjustment is a viable method and solves that problem. It has been used for a 100+ years. Pressurized greasing happens everywhere inside without spinning because the seal on the inside. There is only one exit point for the grease. The hub will end up full of grease. Grease naturally goes everywhere but the spin method could be slightly better. I agree with you 100% 😀🔧
Nice work. Easy to follow. No excess. A+
Thank you! So glad to help 😃
Thanks for the detailed video. Just what I needed to see.
No problem glad to hear it! 😃🔧
Great video. Best one I've watched, and I now feel comfortable doing this myself. FYI, I didn't have a socket that would fit the grease/dust cap, so I used a piece of PVC pipe that fit great and worked perfectly.
Glad it helped! Nice work. Yes!- Nearly anything that fits the seal and hub can work to install it. I have been known to use just a hammer with much success in a pinch. But, a proper spacer is always best and can be found using other materials like you did. Nice creativity 😃😃
Thanks so much for the extremely thorough video.
No problem! Glad it was helpful! 😃😃
Great job - easy to follow, good tips, glad you cover tools to use
Glad you like them!
You still ended with a little bit of preload on the bearing. That is perfectly fine. I am a aircraft mechanic for 35 years now and they use the same setup for the Landing Gear wheels, just much bigger tapered roller bearings. We torque them up to a certain amount to seat them and then back them off loose and torque the nut to much lower amount and the nut will always be more then hand tight…so some preload on the bearings in the end. The locking method for the nut is more then a cotter pin on airplanes! Good video with lots of good information for the average person with a trailer. I see plenty of trailers on the side of the road with the bearings blown out…especially BOAT trailers. I just towed my boat 1000 KM no problem because I serviced the bearings before I left…do it once a year.
Thank you! i appreciate that. I would love to see an aircraft wheel bearing video. Very cool 😃
Very comprehensive! Thank you.
Excellent! You are welcome 😀😀
An even easier way to pop that bearing and seal out it to put the drum back on the spindle, thread the nut on, and pull. The nut will pop the seal and bearing out. Great video.
Great trick. Super fast 😃🔧
Great instruction video. No BS, no wasted time and I like it.
Thank you
You're welcome! Thank you! 😃
Yall are the best ! thanks !
Thanks! 😃😃
Top notch video! Similar content providers take note, this is how its done. L&S
Thank you! I really appreciate that you liked it 😀😀😀
Very nice information. Most people will not be able to work on their trailer without the boat on it like you did here. Unless they live lakeside or something.
Thank you! That is so true. Most times it is the same for me except in this case. I recommend using proper jacks and stands and proper methods in any case for safety 😃😃
Here are a couple of beverages for this very detailed and comprehensive video.
Wow! I really appreciate that 😃. Many many thanks! 🍻🥂
@@EasyFixShaun seriously. You should be an instructor. So much knowledge and detailed patient instruction.
I really appreciate that so much thank you!! In person instruction will always be best but it's so hard to do. I love the youtube format for sharing experience and ideas. It's looking like the best format for me so far! I checked out your ranch/farm and videos! Very cool 😃😃
Interesting I didn't even know they made a tool to push in the races, I've always used an appropriate sized socket. Good video!
Thank you. Great tip! A scrap piece of wood could be used. The spacers are the best to make sure seals are perfect. But, not needed. Grease seals just need to be even all the way around and there are several ways to do it 😃
Best bering greasing video out there!!!
Thanks
Wow, thanks! Glad to help 😃😃🔧
Very well done, nice work.
Thanks 😃😃
Excellent video - something to be proud of.
Thank you very much! Very kind 😃😃😃
when putting the outer cups in you can grind the outside face of the old cups so that they slid in and out then sit them on top of the new ones and hammer them in, this will prevent any damage to the new outer bearing cups,
very good vid
Great tip! 😃😃
very helpful, thanks
Glad to help 😀😀
Great demonstration ... especially the preloading discussion and demo. I may need a "skosch" more time when I do my repacking but I'm sure it will work out!!
Thank you! A lot of time went into this video to offer several ways to see and understand how these bearings work. They are super simple but need to be set up perfectly for best results, in my opinion. I am sure you can do it! 😃🔧
Great video on complete PMCS!
Glad you enjoyed it! Forgive me but what is PMCS?
Military term,. Preventive Maintenance, Checks, and Services.
Excellent video
Thank you very much! 😃
By far the best video out there for this job!!!
Thank you! Made my day 😃
great video many thanks
You are welcome! 😀🍻
Great video, Mister!
It was very professionally done and full of important information.
Thanks!
You're very welcome! Thank you! 😃🔧
Going to be doing this on my rv tomorrow thanks for the help 🤠
No problem 😃😃
Awesome. Thxs brother man? Love your commentary!
Thank you! 😀😀
Great video, thanks. Just subscribed. I appreciate how you described the different size of bearings👍🇺🇲
Thanks for the sub! I'm really glad you like that part. One of my favorites too 😀😀
one of the best vids i have seen on this ,great job!
😃😃😃
My car trailer I’ve not serviced Ed in like 10years! Hahaha
Rolls like a champ! But I’m going to do it as soon as we get a warm spell…
By bearings are probably marbles in there! Haha
Very nice! She's probably due for some grease at the least. Maybe even an adjustment. Bearings in trailers last a long time with normal use. One of the things that makes trailers such a valuable tool 😃
Great video and now that I know how, I need to get it done for my husband....😂 or not. I will supervised.
😂 Good luck with your project 😀😀
Well done Shawn!!!!
thank you 😃
Wow. Great video. Links to parts and all. 10/10 thanks!
Glad it helped! No problem. Glad to help out and pass along some information 😃🔧
very thorough on your work . Thanks learnt a lot
I tried to show all the "ins and outs" to help give ideas 😀😀
Great video. Thanks for the detail.
Thanks for commenting! Thank you. Really appreciate that 😀🔧
This has been fantastic! Thanks for sharing.
Thank you! I am so glad you liked it! I didn't mean to make it so long. It is just how it came out and I went with it 😃🔧
Great video! Exactly what I needed as it looks like I have the same Four Winns trailer, but with a disk brake. Thanks!
Thank you! No problem glad to help 😃😃
Thanks you showed me exactly everything I was looking for.
You are welcome! Glad I could help 😃🔧
Great Job!! Thanks
Thank you!! Anytime glad to help 😀😀
Great video
Thank you 😃
This was so informative. I did however notice a wood chip fall into the grease starting at 49:46. I think as the grease heats up any chip could flow into the bearings and probably cause damage. Keep up the great vids !
Great point and good eye! I think I picked that chunk of wood out of the grease right after it happened. Sorry I didn't show that. I am glad you liked it! I am working on some new ones now 😃😃
Thanks for your video. Very informative, no nonsense.
No problem! I am glad you liked it. I tried to include everything 😀🔧
Best all business the right way video. Professional
Thank you 😃
Outstanding info, detail and notes.
Thank you. Did you get your trailer fixed up?
I just started my wheel bearings on my 5th wheel last night. I used a flat pry bar and I clamped a little clamp toward the top and hammered up like the seal extractor. It's good in a pinch.
Excellent idea. Sometimes you got to make the tools you have work. Or even make a tool from scratch 😀🔧
wonderfully done thank you!!
Glad you enjoyed it! Happy to be of service 😃😃