Seeing how floppy everything gets i started looking at IRL mining equipment for ideas and one thing that stood out was so called "mucker loader". This particular machine had a conveyor with a scoop that lowered to the ground, then a small excavator arm is used to shovel rocks into the scoop, on the conveyor, and ultimately into an awaiting transporter. This idea may work the best for the trailer here since the arm does not have to lift anything, only to scoop stuff along the ground onto a scoop/door that then tilts and dumps the material into the grinder. Better yet, that whole action can be automated down to one switch: The switch lowers the scoop. When loaded the switch lifts the scoop. After a timer runs out the grinder starts and the piston pushes the material into it. When the scoop is lowered, the pistons retract as well. Put drills on a timer so they stop and don't waste the fuel.
I agree. I think this has potential. One of the problems with the bulldozer was it pushed the trailer and hung up at the edge because they were separate pieces. If the scoop/crane thing is attached to the trailer I think it would alleviate this issue and the rocks would pop up onto the lift/gate thing, what ever you build, more readily. Either way this has been very entertaining to watch you figure out. I look forward to the next episode. Keep up the good work. Oh and as one of your other viewers mentioned there are small triangle pieces on the gates at the warehouses.
Kan, Just change the tip of what you have by removing the 1 drill and placing 2 drills (or any even number of drills with rotating positions opposite each other) that face each other and that are on their own pistons to extend in and out. This way you are squeezing the drills together against the rock and the drilling force works in your favor. Think of how you would hold onto something with your thumb and forefinger. Where the thumb and forefinger touch is where you want the drills placed. I hope that makes sense. To make it even better, allow the drills to also rotate down to the ground. This way you can get those blocks that are barely out of the ground.
kAN use the small ramp top pieces (like 2 x 5?) that are on the warehouse roof for your wedge pieces. I know it would be resource intensive, but maybe double up on the horizontal pistons for extra stability. The counterweight did help a little bit also I saw it move.
I've had great success just loading a tiny mining vehicle on the back of my refinery trailer. The biggest issue I'm facing with that is that it doesn't have a built-in resource collector, so I might have to consider a slightly less tiny vehicle in the future. - On the bright side I can easily switch it out with a small logging vehicle and the refinery rig is just as good. On the subject of wedges: the gate houses at the warehouses have some blocks that might do the job.
You can make a nice conveyer which automatically transport rock pieces from ground to a grinder, all you need is to drive near pieces and push them to the conveyer.
With a Level 5 seat, you can eschew the 2 electric motors to turn your robot arm. Use 2 steering bearings set to rotate anywhere up from 90° in both directions from the seat to get the full 360° rotation. You can use a 3rd one, each set at the max 120° for better control.
I don’t really under stand why kan wouldn’t just make a mining vehicle that just uses bearings to move, and have pistons to raise over crushed rocks, and have it be picked up automaticity, maybe the lag would be to much, it seems just to complex to have to use 7 controls. I don’t see the point in building a complex system that requires you to put in manual input.
@@ermimprettysigmaphonk Not only that but it is built in a way that makes it as inefficient as possible. A drill needs pressure behind it so putting a suspension behind it takes away the pressure until it is fully compressed. Also suspension is known to nuke your frames. This is just plain stupid.
The wedges from roof of the warehouse works perfectly for this. There are 2x8 wedge on the very top of the ramp. I used a similar method. Using the piston to grab the rock with the wedge piece. and use 2 bearing arm to flip the rock onto the truck. Kind of like a front loader. I recommend also to attach the drills on your pushing wall because that will give more spaces for the resource collector to grab the rods. I would also add some 1x4 metal rods on top of the piston stack to act as a guide so it won't sag. As I mention before I use bearings to lift the rocks and sometimes it's not strong enough to lift the square "non broken" ones. So I put pistons on the bottom of the loader to push it up and using the refiner as a counterweight works perfectly. Grinding down square rocks all the way down to rods saves so much fuel and is so satisfying
Also If you are building a loader setup you should aim to build a vehicle for the square rocks and try to break as least rocks as possible, only break to root them up.
I think it might work better if you drill the rocks where they are, then move the resource collectors to suck up all the rods, then move those to the refinery. This way, you never need to pick the rocks up off the ground.
They definitely need to add a way to label our buttons and switches in the hotbar. One thing that I use that makes it all easier is using a Streamdeck where I can setup numbers 1-9 as labelled hotkeys and name them for each of the tasks assigned. Then I have folders name for each piece of equipment and switch as needed. So convenient.
roof of the ware house. the ramp has large wedges AND the top edge of the ramp has small wedges. should work great. also you can detonate pieces out of the ware house, like a stair case. shove the large chunk of stairs in and elevator, take it to a new floor and presto, unlocked parts that you can put in your inventory. yo can geet the 1x1x1 orange wedges from those stair cases. remember. explosive are your friend. :)
You gotta rotate your claw with bearings and controllers to 45 degrees so that it's not the flat edge of the piping. Would look like greater than and less than symbols < > instead of two L's facing eachother.
@kAN Gaming : 1. Instead of using a button to start the drill and one to rotate the drill down, use the same button for the drill and the rotation controller. 2. For “stability” of the arm, use a double-stack piston (one on top of the other - in parallel-) and weld the connection blocks together. I know, more pistons, but also, I think, less “sagging” (oh, and the same for the “up” piston, one in front -direction of extension of arm, not elevation- of the other, in parallel) Great addition to your trailer 😎👍
Adding some AND gate logic may make it easier to use, for example turning on and swiveling the drill down could be a single switch, or the drills and pusher in the refiner section could turn on at the same time.
I believe another person was using cactus plants as tips for gripping on to things like logs. So putting cacti on your claw might help with picking up stones.
Bring the side door back, then make a rake. Like a 16 block rake that comes out, and rakes the rocks into the side. Maybe with suspension on the bottom edge so it conforms to the ground better. You just pull up beside a rock formation, open the side door, drill off chunks, then rake them into the side all at once.
Put counter-rotating blocks on the teeth, like little wheels, that will pull up on the rock when the jaws close. Like a vertical pitching machine. Also, screw drilling, explosives baby! Save some weight on that arm. OR Just make the claw a big scraper to pull the rocks onto a liftgate. Of course, these sound like great ideas til you actually try to make 'em
I think the best way is a trailer that goes arround the all rock, mine them and have the collector close enought to gather everything. Grabing is hard in this game
there are 2x1 wedges on top of the warehouse at end of the big ramp with all the other ramp pieces, they work really well for making a grabbing mechanism!
I haven't tested much on rocks but I have found some success with a 4 fingered hand/claw design similar to the ones on Dr Octopus' arms for grabbing vehicles. Maybe tip the fingers with a high grip material.
Maybe the two sets of rollers (tires) rotate together inwards to make it easier to grab things (of course they are much heavier)... Some guard rooms in front of large warehouses have fences and usually have lighter wheels
To pick up rocks, use a dual rotating pipe, like in conveyor belts, but in a way so when it squeezes the rock, the friction and rotation of the pipes pushes it up. Not only will it help lift by forcing it up, but it will also help by not rubbing something static and be harder to move.
2 Ideas. 1. Maybe use rotating bearings to spin the forks under the rocks instead of pistons. 2. Use suspension on the tines of your forks to get all the tips to touch the ground at once. Might make the forks too long tho IDK.
Put a bunch of drills on the front of a vehicle with the containers and refiner on the front, add rails to keep the rocks in, it’ll be much simpler and faster, and you can use the trailer for transportation of the vehicle and extra chests for the materials
should've used a conveyor belt system to drag the rock up and into the drill chamber or the rock crusher and just make sure you can tow the conveyor behind the trailer makes it easy but make sure your truck can haul it
Kan put tires on the claw rather than scooping it up. Tires have a lot of friction as you know. In theory hopefully the weight of the rocks won’t be able to slip by the tires. I would say cacti but I don’t think there big enough so, but try both
There's four things I'd do: 1. Add stabilizing blocks along the crane arm, at least for the length of the detracted arm. 2. Combine the pusher button with the drill button to reduce buttons. One wouldn't use them separately anyways 3. Use a sensor mechanic to activate the seats "W" and "S" mechanic. This can be then either detracting and expanding the arm or moving it up/down. This would save you two more buttons 4. To save one more button, you could try to eliminate the "crane activation button" by trying to replace it with a sensor detecting if somebody is sitting on the seat. This would save you up to 4 buttons Otherwise, great stuff!!!!
And another one: I've seen the hitbox of the ramp pieces working way better when trying to push blocks beneath "floating" stuff, like you wanted to do with the pipes and the rock. Maybe putting those instead of the pipes end pieces work better. You may have found those pieces on the warehouse roofs
Drill from above... negates all that bouncing annoyingness. I tried a 4 sided claw style with the large wedges, worked well enough haha. Pistons just too rubbery to do this right😭😂
It's a good idea -- I hope you can get it to work. Have you considered a more industrial style crane to eliminate the sags and wobbles? E.g., with a gantry crane to transport rocks from the mine to the grinder. I'd also drill directly downwards too, possibly using the same gantry.
As for the inventory. I loop the constructor bot's output storage to the input storage. That way when I build a low tier block, it can immediately be used for the next tier. That also lets me just add more storage with out worrying about which side I need to add storage.
The claw might work better if you make it out of a high friction block to hold the rocks from the sides instead of trying to scoop it up from underneath
Kan: Let's put a crane in a trailer with a refinery that compresses the rocks into some drills so we can optimize our farming. ScrapMan: Just put some drills in the front and then it takes it automatically. "Cada uno tiene su forma de hacer las cosas y no es culpa de nadie, la culpa la tienen los que juzgan a quien hace las cosas distintas" - Some spanish dude.
There are two wedges on top of the warehouse at the top corners of the ramp that you can collect. Also, change your arm to be more of a backhoe style instead of the extending pistons. That might be less floppy.
We really need the wedge and corner blocks for materials. Maybe they could make them so you can switch from the cube to the other options the same way you choose a vacuum tube length.
I like the idea, but it will take so much time to grab rocks from one rock formation, like forever. What I did in my world i created a vehicle with 8 drills on the front. 4 on the very bottom of the vehicle and 4 above them, it goes true stone like through butter. Also my 2 resource containers are one block sapareted from the drills, it just sucks the rocks inside, and behind them are the 2 refiners, very fast way to do it. It's like your truck but the resource containers are on the place where your motor is or under the place where your driver seat is. Vehicle is really easy to make, but it is very very good and most importantly it's fast, I did like a whole forest with 10 formations for 2 days, maybe even faster. Also i noticed that the controler is much better to power up your drills than any engine, level 5 controler on max speed power to a drill, it's much more consistant than the engine. I hope I helped a little bit or just gave you an idea or inspiration for something better because that machine honestly is just a waste of time, btw really good content keep up with the good work💪
KAN! The lowering piston should only extend about 10 blocks, so the claw is touching the ground. Extending the claw too far down, pushing it into the ground, is making it harder to use. Also, try lowering the drill speed.
I experimented with the same thing that you made right beside sagging is what is causing them not to grip better and there's certain other materials that can use for July charm better the piping doesn't have good grip you had something at Maple decrypt on to it but also at the crib is able to make it slide
It would probably take a bunch of extra logic, but it would be cool if you added a button that when pressed would automatically return the arm to the position above the refining area and drop the rocks in.
Switches 8 & 9 could be combined to one switch. Turn it on to activate the drills and pusher wall. Turn it off to stop the drills and retract the wall.
seems like the block that hold the sideways expanding pistons in the claw is kinda closing the space inside de scoop, and it's preventing the rocks to go up
i suggest that you add cactus inside the rock holder-thingy you will need to make it bigger but it will help with the rocks from falling out because cactus have high friction.
I got some 2x1x1 wedges from my warehouses. I also think you'll have better luck making a claw with bearings instead of pistons, that way it will scoop under the rock and not poke the sides of it.
I guess you could make a platform that you can place on the ground that raises and tilts, so you can just tip the rocks into your trailer, instead of relying on the Drills lifting. Use the ramp blocks on the platform so that you can just drag the rocks onto the platform, then just raise and tip. ...That said, that's an entirely new creation to drag along with the rest of the trailer.
Seeing how floppy everything gets i started looking at IRL mining equipment for ideas and one thing that stood out was so called "mucker loader". This particular machine had a conveyor with a scoop that lowered to the ground, then a small excavator arm is used to shovel rocks into the scoop, on the conveyor, and ultimately into an awaiting transporter.
This idea may work the best for the trailer here since the arm does not have to lift anything, only to scoop stuff along the ground onto a scoop/door that then tilts and dumps the material into the grinder. Better yet, that whole action can be automated down to one switch: The switch lowers the scoop. When loaded the switch lifts the scoop. After a timer runs out the grinder starts and the piston pushes the material into it. When the scoop is lowered, the pistons retract as well. Put drills on a timer so they stop and don't waste the fuel.
lol thanks
Nice. And/or add some sensor to do switch work. :P
Well using a bulldozer to push the rocks struggled to get over that 1 block height. So your scoop idea will probably run into the same problem.
I agree. I think this has potential. One of the problems with the bulldozer was it pushed the trailer and hung up at the edge because they were separate pieces. If the scoop/crane thing is attached to the trailer I think it would alleviate this issue and the rocks would pop up onto the lift/gate thing, what ever you build, more readily. Either way this has been very entertaining to watch you figure out. I look forward to the next episode. Keep up the good work. Oh and as one of your other viewers mentioned there are small triangle pieces on the gates at the warehouses.
Omg my brain hurts reading all of this, your a genius even my brain isn’t big enough to research all of this.
Maybe use cactuses to grip the rocks.
LIKE SO HE CAN SEE.
OK!
aye
29 likes
And he S A W!
Nice he sawwww!!!!!!!
Boots 🥾 or fingers 👉 have a higher friction than cacti 🌵 , just saying 😉
There are wedges in front of the warehouse on the road by the guard shacks, "the pole arm gates."
ye, i saw those too
@@oneflamey3234 I used them on the front of my superwide semitruck
Yes and on the roof are the yellow wedges he mentioned for sure. He even grabbed one and put it back when he was up there the first time. ;)
Injnj b.f bhh bnhnunuhuh9
Kan, you mastered the art of over engeenering simple things. And you made my day as well
I agree
He doesn't know how to edit tho
Julian Dickens lol XD
IT'S "kAN" ME OFFENDED
Instead of having curved pipe pieces down have straight ones going in👍🏻👍🏻💪🏻🧠
20:40 My new favorite sport. Rock fishing
what dose that have to do with this vid
@@firerp3791 hes literally fishing rocks in the vid
Well I thought that Minecraft redstone was hard... scap mechanic logic is on some different level.
kAN, you're like the Mumbo Jumbo of Scrap Mechanic
I agree 😂😂
This comment is so true
you right, but trailmakers...
We dont do that here.
Or ilmango
Kan, Just change the tip of what you have by removing the 1 drill and placing 2 drills (or any even number of drills with rotating positions opposite each other) that face each other and that are on their own pistons to extend in and out. This way you are squeezing the drills together against the rock and the drilling force works in your favor. Think of how you would hold onto something with your thumb and forefinger. Where the thumb and forefinger touch is where you want the drills placed. I hope that makes sense.
To make it even better, allow the drills to also rotate down to the ground. This way you can get those blocks that are barely out of the ground.
kAN use the small ramp top pieces (like 2 x 5?) that are on the warehouse roof for your wedge pieces. I know it would be resource intensive, but maybe double up on the horizontal pistons for extra stability. The counterweight did help a little bit also I saw it move.
Kan, the suspension won’t work because you closed the claw. That means that the drill can’t compress as when it tries to, it hits the claw.
There are smaller wedges on top of the warehouses as well. I think they are 1 block high and 4 wide. (on the very top of the sloped section) :)
you can get 1 block high 22 degree wedges from ramps on the warehouse.
that just might work good thinking
I've had great success just loading a tiny mining vehicle on the back of my refinery trailer. The biggest issue I'm facing with that is that it doesn't have a built-in resource collector, so I might have to consider a slightly less tiny vehicle in the future. - On the bright side I can easily switch it out with a small logging vehicle and the refinery rig is just as good.
On the subject of wedges: the gate houses at the warehouses have some blocks that might do the job.
Maybe make a small trailer with a recourse collector you can attach to it?
Yes kAN! You made my day!
I'd say a grabber that rotates open on bearings, and have the teeth overlap so they are angled down when grabbing the rock
Normal people: *Surviving and building bases*
Kan: *Automating everything*
For the scoop, in staid of pipes you can use diamond plates they have the highest friction in the game
no, concrete slab has higher friction
@Computer Boy lol
Nope, cactus and manekin foot has the highest friction
@@aserfuller377 diamond is easier made, cactus is a resource you must find ( i think)
skidaddle skidoodle you can craft cactus
Try mining in the forest, yes you have to clear some trees, but the nodes are usually on flatter ground.
4:22 A-D converter tutorial
Yes, stop the ads
19:40
When you play the claw at the arcade...
Good idea
You can make a nice conveyer which automatically transport rock pieces from ground to a grinder, all you need is to drive near pieces and push them to the conveyer.
My helpful advice: When someone makes a mod for survival with less saggy bearings and pistons it should be called the "Botox" mod.
With a Level 5 seat, you can eschew the 2 electric motors to turn your robot arm. Use 2 steering bearings set to rotate anywhere up from 90° in both directions from the seat to get the full 360° rotation. You can use a 3rd one, each set at the max 120° for better control.
Everybody gangsta til kAN is building space hovercrafts that can shoot black holes and destroy solar systems
kan, the king of over complicating things
Tru
Correct
i want to tell you that is very tru
I feel like this is a very overcomplicated solution for mining
I don’t really under stand why kan wouldn’t just make a mining vehicle that just uses bearings to move, and have pistons to raise over crushed rocks, and have it be picked up automaticity, maybe the lag would be to much, it seems just to complex to have to use 7 controls. I don’t see the point in building a complex system that requires you to put in manual input.
@@ermimprettysigmaphonk Not only that but it is built in a way that makes it as inefficient as possible. A drill needs pressure behind it so putting a suspension behind it takes away the pressure until it is fully compressed. Also suspension is known to nuke your frames. This is just plain stupid.
The wedges from roof of the warehouse works perfectly for this. There are 2x8 wedge on the very top of the ramp. I used a similar method. Using the piston to grab the rock with the wedge piece. and use 2 bearing arm to flip the rock onto the truck. Kind of like a front loader. I recommend also to attach the drills on your pushing wall because that will give more spaces for the resource collector to grab the rods. I would also add some 1x4 metal rods on top of the piston stack to act as a guide so it won't sag. As I mention before I use bearings to lift the rocks and sometimes it's not strong enough to lift the square "non broken" ones. So I put pistons on the bottom of the loader to push it up and using the refiner as a counterweight works perfectly. Grinding down square rocks all the way down to rods saves so much fuel and is so satisfying
Also If you are building a loader setup you should aim to build a vehicle for the square rocks and try to break as least rocks as possible, only break to root them up.
I think it might work better if you drill the rocks where they are, then move the resource collectors to suck up all the rods, then move those to the refinery. This way, you never need to pick the rocks up off the ground.
They definitely need to add a way to label our buttons and switches in the hotbar. One thing that I use that makes it all easier is using a Streamdeck where I can setup numbers 1-9 as labelled hotkeys and name them for each of the tasks assigned. Then I have folders name for each piece of equipment and switch as needed. So convenient.
roof of the ware house. the ramp has large wedges AND the top edge of the ramp has small wedges. should work great. also you can detonate pieces out of the ware house, like a stair case. shove the large chunk of stairs in and elevator, take it to a new floor and presto, unlocked parts that you can put in your inventory. yo can geet the 1x1x1 orange wedges from those stair cases. remember. explosive are your friend. :)
good pun at the end... it needs some refinement :)
You should make the pistons on the claw push into the rocks instead of retracting to grap the rocks.
It looks like he just made a big rib cage
Scrap micanic should make a new wedge bot where at level 5 you can design your own wedge peases
You gotta rotate your claw with bearings and controllers to 45 degrees so that it's not the flat edge of the piping.
Would look like greater than and less than symbols < > instead of two L's facing eachother.
To make the grabby thing like get under the rock I think you should make like a triangle hill to make it like sloge under there ;)
Kan, if you drill down from the top the rocks break easier and the drill doesn't bounce as much.
@kAN Gaming :
1. Instead of using a button to start the drill and one to rotate the drill down, use the same button for the drill and the rotation controller.
2. For “stability” of the arm, use a double-stack piston (one on top of the other - in parallel-) and weld the connection blocks together. I know, more pistons, but also, I think, less “sagging” (oh, and the same for the “up” piston, one in front -direction of extension of arm, not elevation- of the other, in parallel)
Great addition to your trailer 😎👍
Changing the shape of the claw from a square to a diamond might fix the grabbing issue.
hey enjoy the vids
You should make the graber mechanism to a pincher mechanism and put the cacti for better grip
Adding some AND gate logic may make it easier to use, for example turning on and swiveling the drill down could be a single switch, or the drills and pusher in the refiner section could turn on at the same time.
I believe another person was using cactus plants as tips for gripping on to things like logs. So putting cacti on your claw might help with picking up stones.
I suggest adding more pistons to the grabber so it has a stronger grab function. 1 on each side might be a lil much to clamp one of those rocks
Bring the side door back, then make a rake. Like a 16 block rake that comes out, and rakes the rocks into the side. Maybe with suspension on the bottom edge so it conforms to the ground better.
You just pull up beside a rock formation, open the side door, drill off chunks, then rake them into the side all at once.
you should make a fold-out roof in two parts so that when it opens it will become a funnel
Put counter-rotating blocks on the teeth, like little wheels, that will pull up on the rock when the jaws close. Like a vertical pitching machine. Also, screw drilling, explosives baby! Save some weight on that arm.
OR
Just make the claw a big scraper to pull the rocks onto a liftgate. Of course, these sound like great ideas til you actually try to make 'em
I think the best way is a trailer that goes arround the all rock, mine them and have the collector close enought to gather everything. Grabing is hard in this game
You could try cactus plants to grab the rocks. You could use the plants to prevent the trailer from sliding around too.
17:28 i really like this idea.
I endorse it 100%
there are 2x1 wedges on top of the warehouse at end of the big ramp with all the other ramp pieces, they work really well for making a grabbing mechanism!
All hail Kan, the King of Over-engineering! Really awesome contraption, but way more effort that its worth haha.
You could rotate blocks on a bearing to get a sort of "wedge"... and actually you could just kind of spin the blocks to push the stone up.
I haven't tested much on rocks but I have found some success with a 4 fingered hand/claw design similar to the ones on Dr Octopus' arms for grabbing vehicles. Maybe tip the fingers with a high grip material.
You should dibble piston your claw arm so it’s not so lanky 👍😊❤️
Maybe the two sets of rollers (tires) rotate together inwards to make it easier to grab things (of course they are much heavier)... Some guard rooms in front of large warehouses have fences and usually have lighter wheels
Kan you need high friction blocks for grabbing things. Try cactus they work great. Also, we need a mech leg tutorial!!!!
Double up the pistons top and bottom to reduce sloppiness, and there are smaller (1x2) wedges on the top of the warehouses.
To pick up rocks, use a dual rotating pipe, like in conveyor belts, but in a way so when it squeezes the rock, the friction and rotation of the pipes pushes it up.
Not only will it help lift by forcing it up, but it will also help by not rubbing something static and be harder to move.
Hey KAN Gaming, for the rock crusher machine the grippers you can put a cactus on the ends for extra grip.
The repeated realizations that this isn't going how you want it to is what Scrap Mechanic is like all the time for me.
2 Ideas. 1. Maybe use rotating bearings to spin the forks under the rocks instead of pistons.
2. Use suspension on the tines of your forks to get all the tips to touch the ground at once. Might make the forks too long tho IDK.
Put a bunch of drills on the front of a vehicle with the containers and refiner on the front, add rails to keep the rocks in, it’ll be much simpler and faster, and you can use the trailer for transportation of the vehicle and extra chests for the materials
should've used a conveyor belt system to drag the rock up and into the drill chamber or the rock crusher and just make sure you can tow the conveyor behind the trailer makes it easy but make sure your truck can haul it
the rocks are hitting the block in between the claw-opening pistons, just add an extra vertical pipe piece to add clearance.
If you love trucking play spintires/mudrunner or snow runner (I recommend mudrunner over snowrunner)
22:27 DOESN’T PAINT HIS BEARINGS
Kan put tires on the claw rather than scooping it up. Tires have a lot of friction as you know. In theory hopefully the weight of the rocks won’t be able to slip by the tires. I would say cacti but I don’t think there big enough so, but try both
for orange wedges go to warehouse and blow off staircases and hammer them to the lift to get them outside.
There's four things I'd do:
1. Add stabilizing blocks along the crane arm, at least for the length of the detracted arm.
2. Combine the pusher button with the drill button to reduce buttons. One wouldn't use them separately anyways
3. Use a sensor mechanic to activate the seats "W" and "S" mechanic. This can be then either detracting and expanding the arm or moving it up/down. This would save you two more buttons
4. To save one more button, you could try to eliminate the "crane activation button" by trying to replace it with a sensor detecting if somebody is sitting on the seat.
This would save you up to 4 buttons
Otherwise, great stuff!!!!
And another one: I've seen the hitbox of the ramp pieces working way better when trying to push blocks beneath "floating" stuff, like you wanted to do with the pipes and the rock. Maybe putting those instead of the pipes end pieces work better. You may have found those pieces on the warehouse roofs
Drill from above... negates all that bouncing annoyingness. I tried a 4 sided claw style with the large wedges, worked well enough haha. Pistons just too rubbery to do this right😭😂
It's a good idea -- I hope you can get it to work. Have you considered a more industrial style crane to eliminate the sags and wobbles? E.g., with a gantry crane to transport rocks from the mine to the grinder. I'd also drill directly downwards too, possibly using the same gantry.
Add a triangle angle piece at the end of the claw to help the scooping
Creativity +10, Efficiency -1000, Fun +768 - Thanks for a nice vid!
Instead of using the pipe pieces on the claw use the cactus plants because they have the best grip
There's wedges in warehouses... in the front gate... 1x2 blocks... hehehe
As for the inventory. I loop the constructor bot's output storage to the input storage. That way when I build a low tier block, it can immediately be used for the next tier. That also lets me just add more storage with out worrying about which side I need to add storage.
The claw might work better if you make it out of a high friction block to hold the rocks from the sides instead of trying to scoop it up from underneath
Kan: Let's put a crane in a trailer with a refinery that compresses the rocks into some drills so we can optimize our farming.
ScrapMan: Just put some drills in the front and then it takes it automatically.
"Cada uno tiene su forma de hacer las cosas y no es culpa de nadie, la culpa la tienen los que juzgan a quien hace las cosas distintas" - Some spanish dude.
There are two wedges on top of the warehouse at the top corners of the ramp that you can collect. Also, change your arm to be more of a backhoe style instead of the extending pistons. That might be less floppy.
For the claw you could build a pusher wall, like in the truck, to push the rock onto the cage part
Lighjter, higher friction pieces like cactus could help grip the rocks better maybe?
We really need the wedge and corner blocks for materials. Maybe they could make them so you can switch from the cube to the other options the same way you choose a vacuum tube length.
I like the idea, but it will take so much time to grab rocks from one rock formation, like forever. What I did in my world i created a vehicle with 8 drills on the front. 4 on the very bottom of the vehicle and 4 above them, it goes true stone like through butter. Also my 2 resource containers are one block sapareted from the drills, it just sucks the rocks inside, and behind them are the 2 refiners, very fast way to do it. It's like your truck but the resource containers are on the place where your motor is or under the place where your driver seat is. Vehicle is really easy to make, but it is very very good and most importantly it's fast, I did like a whole forest with 10 formations for 2 days, maybe even faster. Also i noticed that the controler is much better to power up your drills than any engine, level 5 controler on max speed power to a drill, it's much more consistant than the engine. I hope I helped a little bit or just gave you an idea or inspiration for something better because that machine honestly is just a waste of time, btw really good content keep up with the good work💪
KAN! The lowering piston should only extend about 10 blocks, so the claw is touching the ground. Extending the claw too far down, pushing it into the ground, is making it harder to use. Also, try lowering the drill speed.
I experimented with the same thing that you made right beside sagging is what is causing them not to grip better and there's certain other materials that can use for July charm better the piping doesn't have good grip you had something at Maple decrypt on to it but also at the crib is able to make it slide
It would probably take a bunch of extra logic, but it would be cool if you added a button that when pressed would automatically return the arm to the position above the refining area and drop the rocks in.
For wedge blocks you can throw away one block and then in creative inventory get two wedge blocks
Switches 8 & 9 could be combined to one switch.
Turn it on to activate the drills and pusher wall.
Turn it off to stop the drills and retract the wall.
Could you put a resource collector on the arm and destroy the rocks completely so you can collect it and refine it
Kan you should build a mobile base trailer for exploring and build a attachment point so you could have multiple trailers
There are small wedges at the top of the ramp on top of the warehouse. I use them for my scooper. Also use them for my ramps.
Maybe use some cactus or boots to grip either side of the stone instead of trying to close around it? Might grab rocks better
Kan, when are you going to do a garment box unboxing?
he already did that
I meant another one
seems like the block that hold the sideways expanding pistons in the claw is kinda closing the space inside de scoop, and it's preventing the rocks to go up
i suggest that you add cactus inside the rock holder-thingy you will need to make it bigger but it will help with the rocks from falling out because cactus have high friction.
I got some 2x1x1 wedges from my warehouses.
I also think you'll have better luck making a claw with bearings instead of pistons, that way it will scoop under the rock and not poke the sides of it.
Try using scissors for lifting, should make the arm more stable, then you go bucket with claw
I guess you could make a platform that you can place on the ground that raises and tilts, so you can just tip the rocks into your trailer, instead of relying on the Drills lifting. Use the ramp blocks on the platform so that you can just drag the rocks onto the platform, then just raise and tip.
...That said, that's an entirely new creation to drag along with the rest of the trailer.
maybe you could make wedges by using a bearing at 45 degrees on the arm head? could be glitchy, but might be worth a try
kan for the rock that didn`t wanna stay....put an little gate with an bearing and some pipes
and make it close on an sepparate switch