DIY 2013 2014 2015 2016 2017 Honda Accord Replacing Rear Brake Pads
Vložit
- čas přidán 14. 07. 2023
- Watch how to replace rear brake pads on a 2013 2014 2015 2016 2017 Honda Accord. #honda #hondaaccord
Parts & Tools Used:
Rear Brake Pads - amzn.to/44ctbFC
Disc Brake Caliper Compressor Wind Back Tool - amzn.to/44yoaqE
12mm Socket - amzn.to/4bn25i8
3/8 Socket Wrench - amzn.to/4bONMTn
Brake Part Cleaner - amzn.to/4dF17iC
Brake Grease - amzn.to/4bN376F
Adjustable Wrench - amzn.to/3WPlWSK
Jack - amzn.to/3QUtgZr
Jack Stands - amzn.to/3wLl5rt - Auta a dopravní prostředky
One thing that is missed here is that the cross pattern on the caliper has to match the pin on the rear plate of the brake pad. If it does not line up it will create excess pressure and wear the pad in no time. I like you must have been lucky a half a dozen times before I hit this issue
I have not been that lucky but I went back and ensured the cross pattern on the caliper matched the pin on the plate. Thank you for the feedback.
Good job All is ok, but next time don't forget the jack stands. ✌🏽
Yep, thank you.
Another great vid 👍
I did 2 vids on this with pads and rotors for both front and rears since I was getting a clown horn noise when braking
Greatly appreciated! Cheers!
Before mounting the wheel back up, pump up the brake pedal. then use the parking brake to keep the wheel from spinning when you tighten up the lug nuts.
Very good tip! Cheers!
Or merely pre-torque the lug nuts with the impact wrench and lower the vehicle to the ground for final tightening...
Great video
Thanks!
Great video thanks! I've had my issues with this task... 😢
You can do it!
You installed your caliper pins in the incorrect order. The pin with the rubber bushing and the line machined around the flats goes on the top. I removed both pins from my caliper bracket yesterday and got them mixed up. I had to go find an exploded diagram online to see where they went. Supposedly the rubber bushing has something to do with mitigating vibration when braking...
Thanks for letting me know. Got distracted and forgot which order. I know it helps with evening out the travel to wear pads down evenly. Gonna swap them in the correct order. Cheers!
Was the handbrake off the whole time
Thanks!
Glad our video helped. Greatly appreciate the donation. Cheers!
thanks
You're welcome!
One thing I would like to add, it is best practice to line the channel on piston face with nipple on break pad.
Thank you for the suggestion.
do you have videos on how to do brake flush on honda 2017
I do not at the moment. Thank you for the suggestion.
The tool to rotate the caliper back was new to me. Awesome, Thank you. i spent an hour trying to use c clamp, cussing and wondering what i was missing.
Glad it helped
Dude! Me too. I was so mad it wouldn’t compress😂
Were do u get one of them
@@nickolasrosenthal7757 Amazon for cheap
If I could add a picture I would I snapped a 12 inch c clamp using a 15 inch cheater bar for leverage before I came to this video
hello and hi what is the torque spec for honda hrv 2020? on the front and rear brake thanks all the bolts
50 N-m (5.1 kgf-m, 37 lbf·ft) Front Caliper
108 N-m (11.0 kgf-m,80 lbf·ft) Front Caliper Bracket
35 N-m (3.6 kgf-m, 26 lbf-ft) Rear Caliper
108 N-m (11.0 kgf-m, 80 lbf-ft) Rear Caliper Bracket
@@MobileCarMechanic hello also what is the torque spec for spark plugs on honda hrv 2020 with a grease and the gaping on spark plugs should i change it or leave it when i buy the spark plugs?
So no need to open up brake reservoir when pushing caliper piston back?
If your just doing 2 axles then you are good to go, if you did all 4 wheels then it may leak.
@@MobileCarMechanic ok, good to know. Thanks for the reply.
Pretty good job. But you didn’t torque bolts on caliper 37 ft lbs. didn’t lube hardware for disc brakes. Didn’t use silicone on slider pins ( not brake grease ). Minor things but makes a difference. Thanks
Thanks for the info
Should try a better angle , couldnt really see much and couldnt see how far out the break pads supposed to go
Thank you for the feedback! Cheers!
Other than the switched caliper pins, my only other issue is the rock chock!!! 🤣
Thank You for your feedback, Needed to include a little bit of nature in our video haha
@@MobileCarMechanic 😂
You must be a renter. Spraying and lubricating with nothing underneath 😂
Haha it’s my friends driveway.
OMG, is he still your friend? Brake cleaner eats everything and that includes asphalt
I appreciate the video, had no idea that the rear piston was a screw type. Tool ordered to be delivered tomorrow
😄
Careful not to overtorque those guide pins, they're only about 15-19lb-ft
Thank you for the advice!
You put the wrong slider pin, in the top, and vise, versa. 🙄 🛠
Thanks for catching that.