@PLAYINSKILSSRT then you either need to, 1. Get a receiver with a 5v output (either through a singular port or the entire receiver) This might require you to use a different transmitter, unless you can find a receiver compatible with your current transmitter that outputs 5v. Or 2. Get an 8v to 5v converter with JR 3pin connectors (female on the input, male on the output). If you can find one. If not, you can make one. I bought 8v-22v to 3v-15 DC/DC adjustable voltage regulator without connectors and crimped the wires ends to JR pins i had from a spare fan. I then used a 3 pin connector so that the regulator plugged into my receiver on the input side. And so i could plug my camera into the output side of the regulator. This video shows a simpler option, but it's not what the camera is made/designed for straight out the box. The connector on the camera by default is a JR male 3 pin connector, which you would normally plug into your receiver. This camera is designed to be used in rc cars, which, the majority of the time, have receivers with a 5v output. But 8v output receivers do exist. (I have one). Aircrafts are different, so i can't say much about that because i dont know much, but the above is what I've done with my 10th scale crawler. Hope this helps.
I was also thinking the same thing. However i was planning to install this on my scx24 with the stock esc. Im not quite sure on the voltage part tho. Will it be ok to directly plug it in?
That thing lost a whole ass battery bar in like 2 minutes bruh... unless I can mod it for cheap and add a better battery, I think I'll go with a better setup.
YOU CONNECT THE CAMERA WIRE TO THE RECEIVER OF YOUR VEHICLE OR AIRCRAFT. PLEASE TAKE NOTE OF THIS.
But thoes put out around 8v he says don't do that lol
@PLAYINSKILSSRT then you either need to, 1. Get a receiver with a 5v output (either through a singular port or the entire receiver) This might require you to use a different transmitter, unless you can find a receiver compatible with your current transmitter that outputs 5v.
Or 2. Get an 8v to 5v converter with JR 3pin connectors (female on the input, male on the output). If you can find one. If not, you can make one. I bought 8v-22v to 3v-15 DC/DC adjustable voltage regulator without connectors and crimped the wires ends to JR pins i had from a spare fan. I then used a 3 pin connector so that the regulator plugged into my receiver on the input side. And so i could plug my camera into the output side of the regulator. This video shows a simpler option, but it's not what the camera is made/designed for straight out the box. The connector on the camera by default is a JR male 3 pin connector, which you would normally plug into your receiver. This camera is designed to be used in rc cars, which, the majority of the time, have receivers with a 5v output. But 8v output receivers do exist. (I have one). Aircrafts are different, so i can't say much about that because i dont know much, but the above is what I've done with my 10th scale crawler. Hope this helps.
I was also thinking the same thing. However i was planning to install this on my scx24 with the stock esc. Im not quite sure on the voltage part tho. Will it be ok to directly plug it in?
Hello, do you know what's the range on this? It would be pretty nice if I could still get video at the same range as the dumborc transmitter
Hi...i just bought these. my screen doesn't shows the below details. like the camera voltage, power 200mw. how do i enable it?
Hi, what is the range?
Where did you get the battery for the camera an the one I have was 80 us dollar.
Wahhh.. Have volume settings.. How about the sound, clear or not sir?
What type is the connector on fpv camera
Where you purchased? I can't find. And thank you for video.
You are welcome I bought it from Taobao China with overseas shipping.
@@jeffreytfl5832 Oh thank you information.
@@jeffreytfl5832 I cat't find on Taobao. More detail information please.
@@Dowan_Gim 57，zROo2bgRldo信 m.tb.cn/h.fQQojLs?sm=d1c408 小飞象4.3寸fpv高清显示屏5.8g图传摄像头双天线航拍遥控器车船
@@jeffreytfl5832 Thank you very much!!!
That thing lost a whole ass battery bar in like 2 minutes bruh... unless I can mod it for cheap and add a better battery, I think I'll go with a better setup.
The batter is removable and you can swap it for a 2s-3s lipo.
Where do you get the battery and how do you connect it can you give me a list of what I need for this
I used a 18650 li-ion battery for the camera, and that is all u need for it to work.
Can it be any battery for the one cell or it has to be a 18650 li-ion battery
@@andrewmartinez6364 so long the voltage is correct, it should work.
@@jeffreytfl5832 ok thanks
Is there something I need to do to connect the wires
It's almost as if an 80 year old made this video