BOSCH 18 Volt Fixing a Bad Lithium Ion Battery 4Ah to 6Ah
Vložit
- čas přidán 23. 07. 2020
- Here you can find a BOSCH battery 18V 6.0 Ah Lithium-Ion
Aliexpresss.click.aliexpress.com/e/_d8f...
Amazon amzn.to/2OSVfrM
Here you can see the products which i used in this video
High Drain Lithium LiitoKala HG2 18650 3000mah;
AliExpress s.click.aliexpress.com/e/DYGUf6ne
Amazon amzn.to/30tfmUp
Battery Spot Welder • DIY Battery Spot Welde...
Thanks for watching . And do not forget, Like and Subscribe
Due to factors beyond the control of BOSSY DIY, it can not guarantee against unauthorized modifications of this information or improper use of this information. BOSSY DIY assumes no liability for property damage or damage incurred as a result of any of the information contained in this video. BOSSY DIY recommends safe practices when working with the tools or equipment seen or implied in this video. Due to factors beyond the control of BOSSY DIY, no information contained in this video will create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from the improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not BOSSY DIY. - Jak na to + styl
Wow, very useful video!👍
Glad to hear that!
Very useful video
Super
nice sharing
Interesting, the now battery has been checked
Legal 👍🏻
Nice
Thanks
Good channel
thank you my friend
Goog video!!!
Thanks!
Thickness to nickel strips you used ?
I have two 18V 2.0 Ah Bosch batteries. Since they look nearly identical, I'm assuming the only difference is that the 2.0Ah version only has 5 batteries instead of 10?
Its ok to use a beer can besides the nickel strip?
Hello! Nice video! Like from friend!!!)))
Thanks for the visit
don't you have more wires to balance the cells?
And just how many DIYs have a spot welder hanging around?
almost 0 )
Are they sanyo RX 18650 cells?
Thanks for the share. My pack is an 18v 4.0 Ah Li-ion battery and it stopped charging. The actual voltage is 14V. The fuse is Ok and I descard the possibility of damage batteries. I think the BMS is the problem. The charger is ok becquse I have an additional battery pack the works well. Any idea or hint?. Thanks.
Definitely a dead set of batteries. 14V is extremely low discharged and therefore most likely one set of dead batteries.
Bosch Li.-Ion battery without BMS?
Thank you so much for the video, I have photos of the fuse in my 6.0Ah pack, because the fuse is Open Circuit. Struglling to find a replacement, I know the physical size is Axial Lead 2AG, but don't know the rating. Any assistance?
Bosch Blue, exactly the same as your video
What are the values of each battery
I guess you would know...who makes the best quality battery cells?
Sony vtc6 cell is best
Samsung, LG, Varta. I'm not sure about Toshiba and Sony but they seem to do the job. Of course read datasheet before
why every two battery connected parallel then 4 group connected series what happen if i connect all battery in series it will proceed volt right? or this damage charge circuit? please illustrate
If you connect the 10 batteries in series you will get a 36V battery. You need to use the same arrangement he did in the video.
@@pmarquisYT 36better than 18 !!
@@mrmemoo4483 Yes, but actually no. This case has only ability to handle 4s systems. There are too little pins for balancing circuit in charger. Moreover parallel connections are also to prevent too large current flow through a single cell with the same current flow through battery.
Of course you probably would damage devices connected to battery modified in this way.
what size torx bits driver?
Can we use li ion mobile batteries for drill battery pack?????
if the cells happen to be rated for 15-20 amps max current draw then yes
@@dejanresetar1639 can i use 18v battery in 14.4v brushless drill????
@@wajeehulhassan2182 you'd have to rewire the cells inside the battery, but if u used the 18v battery in a machine rated for 14.4v you'd probably burn i out but I can't be sure off the top of my head I'd have to look for a schematic
How this battery come with no bms board
hi Omar
this type of drill has the bms inside in the drill, to limit the discharge and short circuit. and in the charger to limit the charge
@@CMCdiy thanks man
@@CMCdiyoh i think so.plz state about the charger Amh and V
Bhai tomara ghar kaha he ?
Me tome milna cah to hu .
mujhe nahin pata
i rebuilt mine using LG cells torn out from old laptop batteries. Reused the old connecting plates and soldered them instead of spot welding. Works perfectly.
a proper diy method. Everyone has old laptops they arent using and a soldering iron.
I need help, please ...
How can I help you
@@CMCdiy i need bocsh 18 volt battery signal resistor value, for the drill Modal Hdh181x ...
This resistor in used NTC and C terminals in battery ...
Please help me ...
After you download, reply to me because I will delete the links
@@CMCdiy than you very much, Sir ...
I think why this kind of tools battery dead is because of there is no balance charging board inside...that is the biggest bulshit of those companies.
На русском языке смотреть буду
Наслаждаться .
Спасибо
All went well until I saw a battery terminal tool was needed.. No worth it for the average diy guy..
Too much distractive crap noise; not enough verbal or texted instruction: Got bored and annoyed by the 'musac' after 20 secs and kicked the video into touch.