Did you use the longest hook joint in the abdomen section, mine also kept falling off because the chest cover pinches against the abdominal section which prevents a lot of back and forward motion, so it does tend to pop off that's if you move it too much over a certain point. So you have to move the hip section if you want a more bent pose.
@@J.KINGTOONZ GET ONE BRO!! you can get a good ender printer for like a 100 bucks which is pretty cheap considering the other prices for other printers
@@J.KINGTOONZ if you can afford a printer and a couple spools of filament, buy one! don't ya remember that old saying? when jobs give you money, buy a 3d printer!
@@HasnaRimi Did you put it on the right way? Try straighten the leg and gently press against a table to connect the knee cap to the leg, there should be a small protruding piece that it clips onto.
Yeah you got to push against a table or something, like I did with the back of my piliers but also not to break it at the same time xD. Make sure the 3 is facing the right way, you want the mid of the 3 facing outward so you can connect the knee covering to it later.
Mine was big too. I had to heat it up a little and squeeze it a bit with pliers but not too much else you might break it. Then I pressed down against my table and it eventually popped in place.
You must slide the cover over the joint from the smaller side (joint section) not the hook part because its too large to get it over. If you unsure which way the cover must face, the colour parts of the cover must face the top and bottom, when you lay the black hook joint flat on the table. I hope my explanation made some sense.🙈
I also got a black one but I first put all of them apart for the jointment of 3d print than I closely looked at all the peoces and focused alot. Took me like 1-2 hours to build
mmm that's strange but it generally doesn't clip in nicely either, try rotating the joints 180 and clip the hip covering on again so... maybe the one side doesn't clip properly to the other side.
Yes, it's not easy if you get a knock off like mine, the joints are rigid and not very smooth to slide in each other. They can get stiff and sticky, you might need a little force to combined them but be careful not to push to hard on the small edges because they can break, like I did to mine. I super glued that piece that broke and its not noticeable unless I actually point it out😂
Yes but Lego is made differently, you should give it a try. It's mainly trying to connect the pieces that don't fit nicely together, which is the main problem in this figure.
Yes it doesn't line up nicely with the back holes but try dipping it in lukewarm water(not boiling water) and then gently attaching the yellow to the black skeletal part, it wont completely fit perfectly but it will still function and fit better than before.
Yeh got to apply some pressure so it can click in, like against a table or dip the covering part in some lukewarm water and gentle push it in. It was difficult to put the legs together because of the cheap one I got.
4:52
This helped me so much
I'm glad 👍
I had to throwaway my first one and buy another one lol 😂
this video helped me alot i had to make 3
Damn 3, that must of taken long to connect all those parts together 💀
Oh yea I have 6 bro 😂💀
Thx bro
I cant connect the chest to the mid part it keeps falling off
Did you use the longest hook joint in the abdomen section, mine also kept falling off because the chest cover pinches against the abdominal section which prevents a lot of back and forward motion, so it does tend to pop off that's if you move it too much over a certain point. So you have to move the hip section if you want a more bent pose.
me too
3d printing them bigger and then assembeling them ist so much easier
True and less likely to break.
THIS HELPED ME OUT ALOT! I just 3d printed the skeletal structure of it
That's good to hear and nice man, I wish I had a 3d printer 😢
@@J.KINGTOONZ GET ONE BRO!! you can get a good ender printer for like a 100 bucks which is pretty cheap considering the other prices for other printers
@@J.KINGTOONZ if you can afford a printer and a couple spools of filament, buy one! don't ya remember that old saying? when jobs give you money, buy a 3d printer!
@@monicat6797 That's the first time I heard that🤣
Thanks, it help me out a lot.
I'm glad it helped someone😁
I had so many problems of mine i had to throw some peices just to connect a joint
😂 I feel the frustration
Same bro it was so hard for me to put the arms on practically threw it
@@jordanchristopher3244 😱 I hope its okay now😂
This is almost as bad as Lego
Yo i have a problem with the knee part what do i do
Are you talking about the knee cap?
@@J.KINGTOONZ ye and the shoulder cap it doesnt fit allat
@@HasnaRimi Did you put it on the right way? Try straighten the leg and gently press against a table to connect the knee cap to the leg, there should be a small protruding piece that it clips onto.
@@J.KINGTOONZthe knee part fitted in, Thanks!
Bro the number 3 looking attachment is not budging to the leg
Yeah you got to push against a table or something, like I did with the back of my piliers but also not to break it at the same time xD. Make sure the 3 is facing the right way, you want the mid of the 3 facing outward so you can connect the knee covering to it later.
Mine was having a really big problem Like the body dont comnect or it doesn't fit through cus its too big
Mine was big too. I had to heat it up a little and squeeze it a bit with pliers but not too much else you might break it. Then I pressed down against my table and it eventually popped in place.
Had to glue some of my dummy 13 cause some of the joints didnt want to connect, i also have a fake one
Yeh it's not as easy as some videos make it to believe 😂
Now record one with focus on the parts ......
i don't get it on 15m 23s
You must slide the cover over the joint from the smaller side (joint section) not the hook part because its too large to get it over. If you unsure which way the cover must face, the colour parts of the cover must face the top and bottom, when you lay the black hook joint flat on the table. I hope my explanation made some sense.🙈
I GOT THE BLACK ONE 😢😢😢😢 I CANT FIND THE JOINTS 😭😭😭😭
I see what you did there😂 I hope you find them😅🙏
Lol.
I also got a black one but I first put all of them apart for the jointment of 3d print than I closely looked at all the peoces and focused alot. Took me like 1-2 hours to build
@@sumreenabdullah4929 @Guesty_AnimationsOfficial joke was funnier.
My hip section is all busted and won’t clip in for anything
mmm that's strange but it generally doesn't clip in nicely either, try rotating the joints 180 and clip the hip covering on again so... maybe the one side doesn't clip properly to the other side.
So hard to assemble
Am having trouble connecting the first one
Yes, it's not easy if you get a knock off like mine, the joints are rigid and not very smooth to slide in each other. They can get stiff and sticky, you might need a little force to combined them but be careful not to push to hard on the small edges because they can break, like I did to mine. I super glued that piece that broke and its not noticeable unless I actually point it out😂
It took me days to assemble like im still working on it😂😂😂😂
@@danielapociumbeanu3406 Damn..that's crazy 😂 but you will eventually get there XD.
I hope 🤣
Me too
I think it will be easy for me cause i'm a great builder of Lego🙃
Yes but Lego is made differently, you should give it a try. It's mainly trying to connect the pieces that don't fit nicely together, which is the main problem in this figure.
For me the little parts are the most hardest part to put on probably going to take a other 3 hours
Goodluck! 🙏
The headpart don't fits on mine
Does it keep popping off?
@@J.KINGTOONZ yes
Mine was too hard bcz the chest part doesn't fit 3:18
Yes it doesn't line up nicely with the back holes but try dipping it in lukewarm water(not boiling water) and then gently attaching the yellow to the black skeletal part, it wont completely fit perfectly but it will still function and fit better than before.
The leg is too hard to assemble it kep falin
Yeh got to apply some pressure so it can click in, like against a table or dip the covering part in some lukewarm water and gentle push it in. It was difficult to put the legs together because of the cheap one I got.
Damn really?