Holdpeak HP-770D True RMS Multimeter Review
Vložit
- čas přidán 24. 07. 2024
- In this video we'll take a look at and test the HoldPeak HP-770D 40000 count True RMS Digital Multimeter, which was kindly supplied by Jason at Banggood.com -- www.banggood.com/HoldPeak-HP-...
More Measurement Instrument Tools -- goo.gl/j2kfbp
*MY TEST GEAR ETC*
Solder :- Multicore & Warton Metals 60/40, 63/37 -- Diameters - 0.25mm / 0.4mm / 0.5mm / 0.7mm
Solder Pastes :- Amtech VS-213-A-TF & NC-559-V2-TF
Bench Multimeters :- Keysight 34465A / Keithley DMM6500
H/Held Multimeters :- Keysight U1253B / U1252B / Fluke 289 / Fluke 28II
Power Supplies :- TTi QL355T / Keithley 2230G-30-1 / EA-PS5040-40A
Multi function Tester :- Fluke 1653B
Electronic Load :- ARRAY 3723A
Oscilloscope :- Rigol-DS2200
Spectrum Analyser :- Rigol-DSA805-TG
Signal Generator :- Rigol-DSG4162 & DG1012
Frequency Counter :- Racal-Dana 1998
Variac :- Carroll & Meynell 8A
Microscope :- GT Vision Research Grade GXM-XTL3TV1
Solder Station :- Pace ST100
Rework Tweezers :- Pace MT-100 MiniTweez
Hot Air :- Metcal HCT-900-21 - 320W Hot Air Station
Hot Air :- Metcal HCT2-200-21 - Hot Air Pencil
Screwdrivers :- Wera & Knipex
Pliers & Cutters :- Knipex -Various Models
Tweezers :- Lindstrom & Ideal-Tek
Scissors :- Fiskars Non Stick Micro - amzn.to/2LByYNZ
Ultrasonic bath :- GT Sonic (6 Litre)
Torch :- Olight S1A
High Temperature PCB Jig/Fixture
Switch Cleaner :- Servisol Super10
Freeze Spray :- Servisol Freeze It
*CAMERA GEAR*
Cameras :-- 2x Panasonic HC-X920
Sound Mixer :-- Sound Devices MixPre-D
Sound Recorder :-- Tascam DR-100 MKII
2x Manfrotto 244RC Variable Friction Arms - amzn.to/2qxzl4W
2x Manfrotto Super Clamps - amzn.to/2PolGpn
Video Capture Card:- Elgato Game Capture HD60 Pro - amzn.to/343Ayif
*EDITING SOFTWARE*
Davinci Resolve Studio 16
iZotope RX7
Youlean Loudness Meter
Handbrake
Adobe Photoshop CC
Adobe Audition CC - Zábava
Thank you very much for uploading this review and actually testing the performance of various modes. It annoys me when people call a video a review and just unbox it and push it around a table talking about it. I just started looking for a 40,000 count meter to test micro amps on micro controllers in deep sleep mode. I like that you discussed the back light in detail because the last meter I purchased has a back light that only stays on for 15 seconds which is super annoying especially since these back lights use so little power you could leave them on for days and still have plenty of battery life left. It is frustrating how companies come up with good ideas and then mess it up by failing to pay attention to other details... I like the backlight + lighted selector knob + ambient light sensor but why the heck did they not think "oh we should give people a manual override while we're at it".
Hi, and thanks for the kind comments. 👍 Happy to hear the video was useful and covered the functions you were interested in on the meter. This little meter has a lot of pluses, but just like any other meter I guess it also has the odd negative point, like the manual light override.
Cheers
John
Yt never notifies me about your videos, I have so much catching up to do! I reviewed this meter the other day too, also sent to me by Jason from Banggood!
Perhaps unsub and re-subscribe to my channel mate, see if that helps with notifications?..
Yes I watched and 👍 your HP770 video.
Cheers
John
Another great video John. As always a BIG 👍 from me! Looking forward to the next on. Please don’t leave it to long?
Thanks Steve 👍.. I'll try mate.
Cheers
John
Ficou bom o vídeo ❤
Thanks buddy 👍
can the backlight be turned on manually too?
Excellent review. Did you measure the burden-voltage of DC mA/uA range? Thank you very much.
I didn't I'm afraid. I will bear this in mind for future reviews though.
Thank you
big thx!!
👍👍
I have a trouble with multimeter on HY3131 chip. Can anyone, who have HP770d measuring the resistence on resistor 10MOm near the HY3131 (possibly R39). Thank you.
The thermo couple may be a different type, some cannot read above 300
Perhaps so mate, I don't particularly like the metal stick type thermo probes to be honest, although they can be handy for some things I guess.
Meeself?? Subscribed! 😁
John-Orbiter, the higher the model (HP-770K) means better and more features?
Well done, sir.
Hi.. Apparently the 770k is more for automotive testing. You can compare all the different models here..
www.holdpeak.com/index.php?s=/Home/Product/search/keyword/HP-770
sir what's about holdpeak 6205 clamp meter! is it good?
I have not tested the Holdpeak 6502 clamp meter however the Holdpeak meters seem ok basic use. However see if you can find some reviews on meters before you buy them. A lot of info can be gained this way.
hi, I'm looking for a multimeter 40000 accounts with which to calibrate electronic music devices, eurorack modules. can this work? thank you.
Hi.. I would say for the calibration of other pieces of equipment you might be better spending a bit more money on some higher grade test gear, however if this is what suits your budget etc then it is an acceptable little meter which will be fine for general purpose use.
My budget is 100€. What’s the best for this budget?
@@valeriotelese4147 If you can't stretch to the likes of Fluke, Keysight meters etc.. I would take a look at the Uni-t brand meters as I like those and have a Uni-t UT71D which is great. I think they are about £120.
Ciao ti vorrei chiedere una cosa visto che hai recensito questo strumento. Io devo fare una misura di una tensione di circa 300 mV AC con frequenza di 50KHz , secondo te "holdpeak hp-770d" riesce a farla ? Grazie
Ciao, ti rispondo in ritardo. Il multimetro é lento, giá a 5khz da problemi. Un mini-oscilloscopio da 2 Mhz puó bastare.
@@redband788 grazie
@@alessioscazzi7970 Prego.
Good morning from Spain,
What multimeter under 50$ do you recommended?
See if you can stretch a few $ and get an Extech 330.
@@OrbiterElectronics Many thanks.
HP-770K here is HoldPeak-Store: holdpeak-store.com/hp-770k-digital-automotive-multimeter-car-engine-analyzer/
Hmm very nice meter john :-D, shame about the display but not all lcd's are perfect at all angles.
Even some of the expensive brands are iffey at some angles.
I see it's one of those chipsets with a serial eeprom for calibration and features, should be possible to update the eeprom as the melf resistors drift slightly, should last a long time though before it needs a cal :-D.
Things i don't like, the com and v-o-a sockets swapped place, it's what i got used to.
And no slot for an emergency teabag lol :-D. (im a tea-a-holic.)
Hi Harv 👍.. Agreed my friend, the displays arent always fully visible on even mid range meters. Regarding the calibtation.. can't say I'd ever bother with that 😂.. Tea however... that's of utmost importance.
Cheers friend
John
@@m.3041 I dont agree at all, especially considering that for electronics purposes its almost as accurate as a calibrated Fluke 289. Its never going to be as well made or as durable as a Fluke, Gossen or Keysight meter, but bear in mind that this meter is nowhere near the price of one either.
The display on my Klein MM700 is great looking at it directly, but if I’m looking at it from the top, it’s almost completely washed out
True RMS measurement must be tested well for the polluted current waveforms.
Dunno if you guys gives a shit but if you are stoned like me during the covid times you can watch pretty much all of the latest movies on instaflixxer. Have been streaming with my gf for the last couple of weeks xD
@Alaric Jagger Definitely, been watching on instaflixxer for months myself :D
Not a bad meter for 50 pounds, not everyone starting out can afford Fluke or the like. Regards, Dave
Thanks Dave 👍
Those leads look like PVC to me, although fairly compliant. My favorite leads come from probemaster which I use on all my meters. Much nicer than Fluke TL175 etc for less money. I've cut the wires on several cheap leads and the amount of copper is shocking. Big thick insulation and a few strands running through the middle. I guess it's an area Chinese manufacturers feel they can cut costs. Transistor testers on meters make my skin crawl too. If they were necessary they'd be on all the top meters including my Fluke 289. Diode mode should be enough for anybody.
Yes perhaps I should have said silicone 'type' leads :) I'll remember that in future. I like the Probemaster leads too but I only have one set, I do my Pomona leads too. Most of the 'copper' in leads of this type are actually only CCA (copper clad aluminium) and I agree it's not very good, especially if you need to solder it.. Argh :)
Thanks for stopping by buddy
John
while Transistor testers on meters isn't necessary I don't see how that can make anybody's skin crawl over that, that's just plain silly
is this meter can read 3000 uf capacitor
No. Its manual specifies 200uf maximum.
Colega ficaria grato se você me informar um multímetro bom e um preço em conta pra usar na bancada do dia a dia
Como você chama um preço acessível?
Exemplo um teste com um LED que não é necessário para uso custa 300 r$ E outro teste de 290 r$ que não tem o LED e é da mesma marca. Porque as vezes tem teste que tem novidades que não são necessário na bancada vc investe dinheiro desnecessário porque estou querendo comprar um de uma boa qualidade e de um valor razoável já tenho alguns testes mais são antigo quero usar um completo então colega ficarei grato por sua resposta
@@luizmoraes621 Em primeiro lugar .. Tente evitar os multímetros sub-40 muito baratos. Se você não deseja ou não consegue obter algo como um Fluke 87v ou um Keysight U1252B, etc. Pelo menos ainda tente obter uma marca conhecida, como talvez um Fluke ou Extech, Uni-T etc mais barato, pois eles têm alguns medidores acessíveis. Por exemplo, o Extech EX330 é um excelente medidor para eletrônicos, embora não seja um medidor True RMS, eles tendem a custar mais. Confira o Fluke 117 ou 179 se você precisar de True RMS. Ou basta digitar no Google .. 'Sub $ 150 multímetros' ou qualquer que seja o seu limite. Leia os recursos do medidor, etc. e verifique se seus requisitos foram atendidos.
Ele es Melhor que o aneg 870 ?
Hi I guess the HP770 is a similar meter to the Aneng 870. However if you want a scope feature the 770D wins.
Please keep an eye on my channel as I will be reviewing the Mustool MDS8207 meter in a couple of weeks which should be a nice meter.
Regards
John
@@OrbiterElectronics, hi. Have you tested both?
@@yankovalsky7696 I did not do a video on the Aneng 870, but I did have one for a while a few years ago & remember it being a good little meter.
The cheaper 20k count ANENG AN870 is way more accurate. The 40k count of the HP-770D is misleading and wasted.
Hi. On what basis do you say so? Did you compare both?
@@yankovalsky7696 Ehhhm the SPECS!
What is the point of 40k count with 0.1% accuracy?? ...that is GARBAGE beyond 10k count!
The AN870 is 0.05% which is twice as good and makes sense for 20k count. I have three, and all are well above their specs.
By comparison the HP-770D costs 3x as much but is 1/2 the accuracy.
If the HP-770D had 0.02%, then for the price it would be awesome value.
As a final note, the 40k count smells like marketing deception crap to me, and as an engineer i HATE this kind of thing.