How to Replace Door Latch on Kia Sorento.
Vložit
- čas přidán 25. 08. 2024
- Rear door won’t open from inside and outside? I used polyester cord strapping to open the door and replaced door latch on KIA Sorento.
#kiasorento #doorstuck #doorlatchreplacement #kia
Thx for the video! Great guide, both my rear doors failed within a week. Cut a strip from a plastic lid since I didn't have any strapping and that worked to get the child Lock off. Saved me over $1000 at the dealership, parts off Amazon were a great price!🥳
Glad to hear.
Please tear this KIA apart and document everything so when I have issues I can just hit your channel. 😂
Great video and explanation!
Thank you for your video. I have never fixed anything in my cars before. I was able to follow your amazing instructions and it worked. It took me over 3 hours because I don't know my tools, but althought I was going slow, I was able to complete step, after step, after step.
slowly but surely, glad it helped.
OMG!!!!....thank you a million times over! I've been combing youtube for a week looking for a video showing this! Tons of them out there but not with the detail you provide. I've had my Kia door partially apart for a week trying to figure out how to do this. Thanks Man!
You’re welcome. Good luck on your door. Thanks for watching.
Awesome trick to get the child lock off, i just did it and worked a treat 👍
Thank you so much for this video!!! I watch it a couple times…
I bought those rubber door stops, the pick, torx set, and… a new door latch assembly ($50).
I got it done on my own thanks to your help - otherwise I would not have normally taken a car project like this on my own.
Many thanks!! 😊
Glad to hear it helps
BTW, If you enjoy camping would you please check out my other channel, here’s the link czcams.com/video/hflm1O_1eKs/video.html Thank you.
Thanks for the guide, I just finished replacing my passenger side rear door latch. Your guide is very comprehensive and complete.
My window did bind going up after reassembly. (I was operating the power window from the driver's door and found for the window to operate, the window switch on the door must be plugged in.) I ended up loosening the three window guide rail fasteners, making sure the guide rail was shifted away from the window and re-tightening. That cleared the problem.
You’re welcome, I’m glad this video help out. Thanks for watching.
Brilliant! I had a thin plastic rule that was a little stiffer. First shot. Thank you so much!
First shot is always a good thing. Thanks for watching.
Thank you for the video, super great walkthrough/guide!
You’re welcome
Ty for sharing youre experience. Big thumbs up !
Thanks for the idea I used a very flexible putty knife that cost about a dollar. Pull the seal back from the inside and in 30 seconds to tries pop the Child lock open.
no problem. few comment actually recommend flexible putty knife, I might give it try on my future repair. thanks for the tip.
Just got this exact car with the exact same problem and I turned on the child lock on accident and this saved me after trying for over 2 hours! Thank you!
You’re welcome, if you could please help me grow my channel by pressing the subscribe button. Thank you 🙏
@@WrenchingRyan❤
I needed this info!!!! Thank you for the guidance
You are so welcome!
great video thank you !!!!!!!!!!!!!!!!
You are welcome!
i used a tupperware spatula, worked perfect no damage great video 👍🏽
Awesome. Thank you for posting! Just completed the project and turned out perfect 😎😁
The video helped me I was able to open the door, thank you
Glad it helped.
Sir, your video was fantastic. the only thing I would suggest is next time. This happens for anyone else. Remove the inner door trim in the rubber gasket. Around the door. Once you do that, the child safety lock is easily accessible.
Period
Thanks for the tip, I always go this way but I better try your idea next time. Thanks again.
We're just pulled the door panel out and then reach around and get the clips loose and go up top get the cable loose and pull that cable from the mechanism and tug on it too just got to figure out which one is the upper and lower
Very Good job. Thank you!
Thank You 🙏
GENIUS. Thank you so much!
Thanks 🙏
It worked. I used the handle of a beach sand play bucket
Glad it worked.
Nice sharing host
Thanks Ate Hali.
Yes, thank you! How much time would it take to complete this fix from beginning to end?
You’re welcome. You probably looking at an hour, took me two hours with camera rolling.
Thanks indeed for your great information
Glad it was helpful!
Great video!!! Funny thing is I have a door latch as well but mine also needs a window grip due to the last person who worked on it put the wrong bolt and crossthreaded the threads.
P.s I don't know how long it took you to open it but it takes me about 15-30 to remove the door panel and westher strip to access the child safety lock. Cheers and keep pumping these cool videos! I wonna see a Sc199 tranny replacement lol!!
Crossthreaded always fun work on lol. I actually open the door on my first attempt but my camera is not recording lol, I have to redo it and took me three attempts and probably 15 minutes before I open it again. I almost film Sc199 couple months ago but my schedule got busy and did not finish filming. Thanks for watching and have a good week ahead.
Great video, thanks a lot!
Your welcome.
I'm wondering how much is this fix cost approximately. I know location plays a role in the local markets, but if you have a ball park cost or average of what you would charge is great.
Honestly don’t know how much each latch cost, but I’ll go ask my parts guy tomorrow and at least give estimate cost. thanks for watching.
Do we really have to do the window part? Can I just keep it as is screwed and rolled all the way up?
You have to do it to remove the window regulator.
Mate you are great
Thank you 🙏
This is a really helpful video. Unfortunately two things went wrong after I finished. The window doesn’t wind down properly anymore and the actuator seems to work in reverse. Any tips? The screw that goes into the middle of the door (the one you needed an impact drill to remove) didn’t seem to bite when I put it back in
Make sure the screw is lined up correctly, if that screw did not bite in your window is probably crooked, also check you actuator cable they might install backwards. Thanks for watching.
@@WrenchingRyan thank you for that help. I will check the screw is lined up. I don’t understand how the cable can be backwards. Could you please explain
@@WrenchingRyan the window now works. Thank you! I took the opposite door panel off to see what the other actuator was doing. When the black cable on one door pushes out, the other one pulls in, and visa versa
Don’t worry - sorted it. The part must have originated from left hand drive vehicle. Needed to reverse the polarity.
2010 Kia Firre
Would this be the ssme procedure with a Kia door that wont open just from the outside?
yes it’s the same, this door won’t open from inside because child safety switch is on. but the main failure is the door latch. thanks for watching.
Hi Ryan on my 2011 sorento the heat is not working, ac and fan work, but not switching to heat do you have anything that addresses that? thanks,, and thanks for posting!!!
Hello, first thing you can check is your coolant level, is it full? if not add coolant and bleed the system, 2nd is if your coolant is full let the engine run until normal temps then check your heater core hose if both of them are hot or same temps heater core is good but if one hose is cooler than the other then your heater core is clogged, 3rd is check your temperature door actuator, the actuator could be stuck on cold position or you have open circuit from your HVAC module or the module itself is faulty. I know there is too many to check but good luck to you and thanks for watching.
Thank you, Ryan so much for all that information , so cool.
You Rock!
I completely understand it.
As it turns out, it was a clogged heater core
Was able to flush it out and now I have heat in the car
Although here in Florida, I do not need it anytime soon 🔥🤣
However, I’m not sure how to correctly bleed the cooling system ,to make sure I have no air
thanks again
@@1610nsb I’m glad it helped
If you have time watch this video czcams.com/video/T7KzeJeplzc/video.html start watching at 22:25
I know I used the BG machine to speed up my process but it’s going to be the same steps without it.
Remove radiator cap
Used spill free funnel and add coolant
Start the engine
Turned the HVAC blower motor off
Turn the temperature to max heat
Wait until the ECT notified the PCM that engine reach normal temperature
Which means the thermostat is wide open and coolant is recirculating, the PCM also turn the radiator blower on to cool down coolant
And that’s the best time to escape the air from cooling system.
Genial me funciono gracias 🎉
Exact same problem
Now you have some idea what’s going on and know how to tackle it. Thanks for watching.
Thanks for the video. @4:52 Do you really need to remove that screw?
G to G 🙏 👍🏻👍🏻👍🏻
man i hope mine never breaks
I hope so. Thanks for watching.
My man thanks for the vid. I have a question my lock is jammed on the pin you can hear it lock and unlock. I had somebody work done the guy tried, i was in a hurry bcz i was moving. Now couple years later need door to open. Any thoughts at all would be of great help. Again thanks for the video.
How similar to this is the front door?
Similar for the most part.
Old bank card did the trick
Great idea 💡
So my drivers door has started making a bit of a buzzing sound when I unlock it, could it be the lock on the way out? I'd rather fix it before the drivers door doesn't unlock 😂
Use a credit card its thicker I had the same problem it was alot easier
Thanks for sharing, I’ll give it a try next time.
Plastic butter knife works KFC
I think anything plastic can slide in would work, thanks for watching.