I built this exact quad except i used 0802 motors from Happymodel and bi blades. Mine came in at 35gm because i used a tiny bipole antenna. Will be switching to tri blades when they arrive. Love this combination!
Good video. I found it very informative. How long do you fly for? I have the same FC, same motor and a 1636 4-blade propeller. With my setup, the gyro is working abnormally at 90 seconds. Is it a heat problem?
my gyro is fine. however, I'm not too happy about the flight time. it is below 3 minutes when pushing the throttle. thus, I m going to build the new 75mm whoop with 45mm props next.
Nice build. I built this on UZ85 base 1102 10000kv 2s and swapt only with the FC you built spi ELRS v2.2 2022 version. Everything OK but the spi ELRS rssi problem start with strength dropped over -100dbm. Did you use the installed stock firmware? or firmware updated?
Great video again!) Did you have the opportunity to compare the latency of walknail and dji goggles? Is there a significant difference in favor of dji?
My gosh why people r building such a shitty drones?! Engines without direct soldering?! U freaking kiddin' me?! This canopy, build weight motors selection... Everything can be done wrong with good build u've successfully implemented. And the worst thing here - someone can accept it as a tutorial...
I built this exact quad except i used 0802 motors from Happymodel and bi blades. Mine came in at 35gm because i used a tiny bipole antenna. Will be switching to tri blades when they arrive. Love this combination!
I think one can get down to 30g with 802 motors, vtx lite, no canopy and happymodel diamond AIO board
Where do you buy the mounting screws and what size?
Nice setup! I've been planning something similar myself, except going with 85mm frame and 1102 18000 kv motors.
nice, should improve flight time
thumbs up for the para 2
Very impressive have good quality video on tiny whoop! By the way, nice knife.
Good video. I found it very informative.
How long do you fly for?
I have the same FC, same motor and a 1636 4-blade propeller.
With my setup, the gyro is working abnormally at 90 seconds.
Is it a heat problem?
my gyro is fine. however, I'm not too happy about the flight time. it is below 3 minutes when pushing the throttle. thus, I m going to build the new 75mm whoop with 45mm props next.
Nice build. I built this on UZ85 base 1102 10000kv 2s and swapt only with the FC you built spi ELRS v2.2 2022 version. Everything OK but the spi ELRS rssi problem start with strength dropped over -100dbm. Did you use the installed stock firmware? or firmware updated?
I didn't update ELRS / Betaflight
Great video again!) Did you have the opportunity to compare the latency of walknail and dji goggles? Is there a significant difference in favor of dji?
Thanks! I never tried DJI. IMO the newest firmware 31 is fine to me even in 1080p!
Which battery should I use for this whoop?
450-550mAh; the new tattus seem pretty good. by the way, I'm working on a new build, I got the weight down to 28g
Does the vtx support gyroflow to stabilize in post?
What flight time did you get? (and with which battery?)
Shouldn't it be VRX DVR instead of VTX DVR?
Walksnail VTX has onboard DVR.
can you share the stl?
look for beebrain V1 you might find something on thingiverse
My gosh why people r building such a shitty drones?! Engines without direct soldering?! U freaking kiddin' me?! This canopy, build weight motors selection... Everything can be done wrong with good build u've successfully implemented. And the worst thing here - someone can accept it as a tutorial...