Build THE BEST Tiny Whoop | The Easy Way
Vložit
- čas přidán 1. 02. 2024
- Thanks for watching ! As promised, below I've attached all the necessary links to either build your own race whoop or get one ready to fly from the Five33 shop!
Want so support the channel? Consider shopping at Five33!
Ready To Fly Whoop: ?ToPasteBoard&
Parts Picker Page: flyfive33.com/pages/race-whoop
Parts:
Frame: flyfive33.com/products/meteor...
AIO: flyfive33.com/products/betafp...
Camera: flyfive33.com/products/c03-fp...
Motors: flyfive33.com/products/betafp...
Props: webleedfpv.com/collections/pr...
Batteries: we bleed (ph 2.0) webleedfpv.com/collections/ba...
- pyrodrone.com/collections/1s-...
VTX: flyfive33.com/collections/vtx...
Tools
T700 Glue: www.amazon.com/T-7000-Adhesiv...
B600 Glue: www.amazon.com/Rhinestone-Adh...
Phillips Driver: www.amazon.com/gp/product/B08...
Mr.Chaus Drone Tune
Esc settings
48khz PWM frequency
Demag High
version
Betaflight / STM32F411 (S411) 4.4.3 Nov 14 2023 / 17:22:54 (738127e7e) MSP API: 1.45
config: YES
start the command batch
batch start
reset configuration to default settings
defaults nosave
board_name BETAFPVF411
manufacturer_id BEFH
mcu_id 003900393535510936323431
signature
name: mrchaus
feature
feature -TELEMETRY
serial
serial 1 2048 115200 57600 0 115200
beacon
beacon RX_LOST
beacon RX_SET
master
set gyro_lpf1_static_hz = 500
set gyro_lpf2_static_hz = 1000
set dyn_notch_count = 2
set dyn_notch_q = 500
set gyro_lpf1_dyn_min_hz = 500
set gyro_lpf1_dyn_max_hz = 1000
set acc_calibration = -64,194,21,1
set min_check = 1010
set max_check = 1990
set rc_smoothing_auto_factor = 25
set rc_smoothing_auto_factor_throttle = 25
set blackbox_sample_rate = 1/2
set dshot_idle_value = 600
set dshot_bidir = ON
set dshot_bitbang = ON
set motor_pwm_protocol = DSHOT300
set motor_poles = 12
set vbat_max_cell_voltage = 438
set yaw_motors_reversed = ON
set small_angle = 180
set pid_process_denom = 1
set simplified_gyro_filter_multiplier = 200
set osd_vbat_pos = 385
set osd_rssi_pos = 226
set osd_link_quality_pos = 2454
set osd_rssi_dbm_pos = 321
set osd_tim_1_pos = 2433
set osd_tim_2_pos = 406
set osd_flymode_pos = 374
set osd_throttle_pos = 2401
set osd_crosshairs_pos = 203
set osd_craft_name_pos = 2441
set osd_warnings_pos = 14353
set osd_avg_cell_voltage_pos = 2049
set osd_canvas_width = 30
set osd_canvas_height = 13
set vtx_band = 5
set vtx_channel = 8
set vtx_power = 2
set vtx_low_power_disarm = ON
set vtx_freq = 5917
set gyro_1_sensor_align = CW90
set gyro_1_align_yaw = 900
set rpm_filter_harmonics = 2
set craft_name = mrchaus
profile 0
profile 0
set dterm_lpf1_dyn_min_hz = 97
set dterm_lpf1_dyn_max_hz = 195
set dterm_lpf1_static_hz = 97
set dterm_lpf2_static_hz = 195
set vbat_sag_compensation = 100
set p_pitch = 69
set i_pitch = 74
set d_pitch = 64
set f_pitch = 175
set p_roll = 66
set i_roll = 70
set d_roll = 56
set f_roll = 168
set p_yaw = 66
set i_yaw = 70
set f_yaw = 168
set d_min_roll = 52
set d_min_pitch = 59
set feedforward_averaging = 2_POINT
set feedforward_smooth_factor = 65
set feedforward_jitter_factor = 3
set feedforward_boost = 18
set simplified_master_multiplier = 140
set simplified_i_gain = 60
set simplified_d_gain = 125
set simplified_pi_gain = 105
set simplified_dmax_gain = 25
set simplified_dterm_filter_multiplier = 130
profile 1
profile 2
profile 3
restore original profile selection
profile 0
rateprofile 0
rateprofile 0
set rates_type = BETAFLIGHT
set roll_rc_rate = 90
set pitch_rc_rate = 80
set yaw_rc_rate = 70
set roll_srate = 70
set pitch_srate = 70
set yaw_srate = 70
set throttle_limit_type = SCALE
rateprofile 1
rateprofile 2
rateprofile 3
restore original rateprofile selection
rateprofile 0
save configuration - Zábava
these videos will undoubtably be an invaluable resource for FPV not only now, but into the future as well. Extremely grateful these exist!
Honestly, this brings back the old Flight Test foamy build vibes back. Loving it!!
Professor Charles.
Dude, this guy actually taught the audience a lot about whoops.
I really appreciate this video, I'm a heavy duty whoop Builder but I'm always looking to learn more, and it just so happens I have all of these parts on hand. Thanks Charles!! 🙏😁
Sweet! Charles is the man, excited to hear what you build!
what a super clean build, SO nice !
Thank you for this sic very informative vid on these tiny whoops. Keep the dope videos rolling 🔥 🔥!!!
Hey, Betaflight settings could add a little bit of weight, should have weighted it after setting up :))
Awesome video guys! Tiny Whoop the world!
Great video guys. Great work Charles
Thank you for that detailed build video! Very nice 🙂
recently been searching for a video like this thank you
Hey team, much appreciated for the shout out! You guys rock.
the baggie trick for motor direction, thanks for that!
probably easier to just put pieces of tape on the motors, and less risky
Very very good overview, close to what I do, my differences:
- Rotate the board so the gyro/rx chips aren't on the axis that take the most abuse
- karate whoop preset
- T7000 on the UFL
- Triangle in the back (it has a flat surface, having that perpendicular to your direction of travel is bad aero)
- Webleed 0702 26500kv v2 motors
- Foxeer Pico Razer camera (RIP) (Also would be nice if a company like 533 used their relationship with foxeer to do a follow up to this camera)
Thanks for doing this, a lot of people come to me asking about the rationale behind the parts I use on my whoop and it's covered here perfectly
Fantastic info!
Foxeer is still selling the razer pico. Why do you claim its discontinued ?
@@chrisbee5481 they're no longer filling wholesale orders for it, what's on their website is likely the last of them
thank you eedok!
Great work you two!!! I can attest that Charles knows what he's doing, saw him crush at the tiny whoop race last night and inspired me to try and get my own Tiny Whoop builds to this level :D
Awesome! lets see it!
Awesome video! Charles is the man!
Really liking these videos you have been putting out lately.
Happy to hear it!
Great vid! Just went thru 99% of this on my own after watching whooptopia… just amazing performance vs the old 25k Mob6 baseline.
Great upload. As a new pilot this is the content I need. helping me get learnt! lol
I love it!
Awesome stuff guys
I have heard of you guys, but my first time seeing a video of this nature. Dude, I would soo buy that build, i can solder, but you soldering it ALL!! Thanks for the video!
Thanks for watching and will keep an eye out for your name in the RTF queue!
@@headsupfpv should be in the RTF queue
Can't wait!!! You should see my order 🎉@@headsupfpv
I watched this 4x..... keep it up.
Awesome video fellas!
Definitely a shot in the right direction! I think the frame is actually more durable when it is cut because it flexes. Camera is no good, the fov is bad and the pinch is better but understandable. The camera mount also adds unnecessary weight, I didn’t look at the weight but I’m guessing you could use something else and save .4-.45 and it would still be durable. If you also rotated the fc it takes like 30 seconds to do and helps with durability as well as the pigtail. Other than that it’s a super solid build
Sweet! Would love to see what tips you have for cutting the frame properly, and I definitely need to try and pinch, I don’t mind the CO3 so far but maybe I just don’t know what I’m missing haha.
Other than this wall of text well done 😂
@tdogfpv knows what he's talking about. Do everything he says.
Are you rotating the FC so the battery is toilet-tanked?
@@headsupfpvit’s the TinyWhoop Pinch cam for the win in my opinion 🎉😊 whoops are soooo much better in the last 18 months …. TinyWhoops 32000kv 0702 on bi blades 😃👌🤟🤪✅
This drone could go brrrrrrr, only suggestion is use the tiny whoop pinch cam, also see if you can do some frame mods to cut down the weight. One last thing I used to put the fc the way you guys did but then I realized flipping it ought saved a half gram in wires. It makes the vtx wires be able to be extremely short and only adds a little weight to the camera wires.
tiny whoops are the bomb
I can build and I prefer building over mass produced whoops. But these custom tailored and built whoops are nice! I gotta have one and the Fatshark analog goggles asap.
Awesome video guys! Those things rip. This looks a lot like Speed Racer 5 😂
😂
Great video. What canopy was it?
Hi everybody. My other channel is Kriss fly. I tested some of the very first tiny whoops.
I am about died from chemical spray drift from my neighbor GMO corn farmer. So I’ve been out of the game for about five years. Things have changed. Can’t wait to build one. If my old eyes can keep up with it :-) stop by both channels say hello. Realize the chemicals you are eating in your food. Over 30 countries have band it and climbing. We deserve better food go grow something worth eating.
Thx for that excellent build video!
What goggles are you guys using?
The Five33 Orqa race goggles
Knoxville TN ❤❤❤
Great video, I had a quick question. I know you guys were soldering to get the weight down, but all of the components in the description would plug into each other, right? So it would be possible to build this without soldering, it would just be heavier?
Awesome build video. Like the antenna mod. It would be a fun fulltime job building whoops all day. Would like to know if the esc and vtx is heavier than a HM diamond esc aio?
Interesting questions, I don’t have the answer off the top of my head however! If we get them in, I’ll check!
Hey, looking to get into the drone building space, and I am trying to find the best place to get started.
I’m local to Seattle Washington and would love any advice for finding a makerspace or events to get my feet on the ground.
Thanks!
Charl south africa, must be AWESOME ,AWESOME AWESOME!!!!!!!!!!!! to walk in shop wuth that much stock and able to pic what YOU want
do u also get a very high core temp when this vtx is below, can go up to 70-80 degrees core temp in fc that ok ?
Evan perhaps Mondo can come up with a carbon base plate similar to the fractal. These combined with trimmed ducts is an excellent build that really performs.
This could be an opportunity for a new product
I prefer the carbon base builds myself and I know a lot of others do as well.
We will look into it ! I think it’s a good idea
Damn...Now I'm obligated to build another.
can you build a walksnail one with the same parts in the vid?
What transmitters are used?
This is a great build! Should probably credit the original thingiverse camera mount creator though... unless i missed it???
Dang just got mine this thing is amazing! On rails I thought I was in angle mode 😮 maybe just include a quick spec sheet so we don’t have to go to the video to see what parts are on the whoop.
On it !
Great build. Now do it with a dji 03! Also do you do builds for others?
Yes we do! Checkout flyfive33.com and the builds page!
Just finished this build, parts ordered with links in description, and my Betaflight Version doesn't match yours. Did you update to 4.4.3? Mine came with 4.3.0. I'm happy eitherway, but was just curious. The build came out under 18g and looks great. Thanks!
Maybe just different board batches in the same shipment, should be able to update and apply the tune super easy, let me know if you have any problems, but glad you like it!
Are any cameras 16:9 and PAL? I'm in btw, looking to build one. We don't have those glues in Africa, blast to you and your first world living ;-)
These cam’s are 4:3 and NTSC by default I believe. But may have a 16:9 pal option!
Im not a drone pro like you guys lol, but for a beginner build you should aim for around 20 grams with plugs on flight controller. Good choice of battery, but for a beginner build get everything with plugs. As you progress in skill you may want to try to make it lighter, but as starting just get a whoop in the air and practice. Also use analog for whoop, its lighter than hd. Just thought i'd share my opinion.
i want one
So, do you think it's possible to build an as good a drone with HDZero?
With current tech, simply not as light!
for the vtx and that fc. the video cable comes the camera into the video in pad and the video out goes to the vtx???
Correct!
@headsupfpv thanks dude appreciate it! Happy flying
Okay now the same for HDZERO whoop please
So..... When can I go on the 533 website, and buy a tuned, ready to fly one??
flyfive33.com/collections/new-products/products/17-2-g-race-whoop-ready-to-fly
Right now 😁
@@headsupfpv We Bleed North East Champs are next month, think I need one for them!
Charles! Where's the hot glue?? lol
You basically described the entire build of Meteor 75 pro.. .....
Wieviel mW Sendeleistung ?
the camera that you choose its only for ntsc system??????
I believe so, NTSC is all we use here as it is the highest frame rate which is best for racing!
Blonde Paul Mccartney! That's why you always looked familiar to me..
I'd be surprised if you've never got that before
lol! Never gotten it , but I can see it!
Is this not basically a BetaFPV Meteor 65 Pro?
The weight savings make a massive gain in performance and getting to that requires a lot of extra leg work, the little things add up!
@@headsupfpv thanks for clarification.
Kids... keep in mind just because you have the same quad doesn't mean you are going to be able to get it to fly like Evan does :D
Link to the camera mount stl?
On thingiverse !
@@headsupfpv Thanks for the reply! What’s it called, or who uploaded it? I looked on thingiverse but I couldn’t find it.
back in my day they were under 100$
Next time use an overhead camera so that we can actually see the stuff you're talking about :)
I’ll work on it !
I'd buy one right now if it was running Ghost 👻
We can do a ghost offering, but it would be significantly heavier, maybe an option in the future!
@@headsupfpv I tried the NBD board with integrated Ghost, VTX died at my first race ☹️
Great video! Also i noticed you have some irritation on your face, I would recommend stop using a razor blade if you're shaving with one. Go to just a clipper/trimmer, and use that, will be better for your face.
lol, I love how there is a Heart from the owner on every comment but mine. im not trying to be mean, but reality is reality my dude. hope you have improvements :)
Eeew don't link PH2.0 batteries.. How dare you...
My bad!
With Betafpv C03 camera - it is NOT best whoop - trust me... :D
I’ve come to like them from personal experience, what’s your favorite cam? I hear the TW pinch is a great option!
@@headsupfpv yes TW pinch, or Razer Pico from Foxeer or even Caddx Ant lite is very good camera for me :)
C03 is solid. 2nd best race cam behind the pinch but the C03 is a close 2nd. It’s the C02 that’s bad.
The pico has a good image but at the cost of half a gram and that makes it not worth it on a racer