How to install a power steering pump on a 6.6L Duramax
Vložit
- čas přidán 6. 09. 2024
- I Hope this video is helpful,If you have any questions comment below. Like, Subscribe and share!!
If you do not have the tools and you are needing them here’s a link for a remover/installer OTC Tools 4530 Power Steering Pump Pulley Service Set www.amazon.com...
follow:
instagram: tylor_chase
snapchat: tylor_chase
Just had this problem last weekend shredded a belt it ended up being a bad pulley on power steering great video thanks from Indiana
As one of the older comments said. I was able to skip removing the shrouds etc. Vacuum pump out fluid, Loosen belt, remove 3 lines, remove wire plastic retainer, remove 3 bolts on front, remove 2 driver side bolts lift out. On a bench remove pulley and brackets swap over and reinstall. I'm replacing the high pressure line up to Hydroboost, so I just cut rubber line/hose
Which high pressure line did you end up using
@@anthonycollins104 I used the ac delco. Hopefully they will last a while
Doing an LMM right now, and it’s easier to pull the pump to booster hose (the one he replaced in the vid) than try to take it off in the truck. Thanks for the vid! I came here because I couldn’t remember which bolt hole the negative battery terminal bracket came off of. 😊
😂😂😂😂❤
Saved me from paying my mechanic thanks man!!
Old man going in. Wish me luck.. you make it looks easy. Thank you
I noticed the match on the bench when you were changing out the bracket. This must mean it's a hot job. Nice video. I appreciate it.
butchtheiw thanks, I appreciate you watching my content.
Great video man! Helped me out a lot with the clear instructions.
I’m glad the video was helpful
Hey boss thanks for the vid, I just did my steering pump and now my belt keeps coming off the balancer, I watched your vid again and didn’t make sure the pulley was flush with the pump
Really good vid it helped a lot thanks for taking the time to make it..
So I just watched this 20 times. Learned a ton. What was that hope house reference? Dying to know.
It’s this place that comes by looking for donations they have jerky sometimes or salsa. They are a place where people that need help would go that struggle with addiction.
But you got to have a snack when your working.
Well I needed a whole week’s worth of meals. Would have been a month if not for this video! Thank you for this!
Great video, idk why they gotta use 12 bolts to hold a pump on
Thanks, That’s Gm for you
Thanks a lot, the best "how to " video ..you ll save me $300 i need only the tool to remove the pulley... I have duramax 2006
I’m glad the video was helpful
Great information, thanks bru😎
What is the part number on that pulley puller?
Great video! 👍 ⭐️⭐️⭐️⭐️⭐️
what size bole was that at the end of the pulley on the original? I've seen others with the bolt on there, because the pulley is just pressed on, was wondering if you put that bolt back on?
I did not reinstall the bolt afterwards I just had it on there to keep the pull on. Not sure what the size of the bolt was I just pulled one out of my bolt bin.
Awesome video!
Very helpful. What would be ballpark cost to have a shop do this. Not the stealer ship. 05 dirtymax
It’s about a 2hr job so just depends on the shops labor rate and what pump you buy.
@@diamondtruckperformance493 thanks. Appreciate ya
Remove upper fan shroud
Remove 3 bolts from front of pump
Remove 2 bolts from side(holding rear bracket to block)
Remove lines
Pull pump out of vehicle and swap bracket on bench
Why the hell would you remove the pulley inside the truck?
Why would you pull the inner fender to remove the nuts when you can easily remove the bolts holding bracket to pump?
I don’t see anyone asking for your opinion
@@danielsotelo6753 waste your fucking time then dumbass
Facts ! Was thinking the same thing when I see that pulley being pulled off
@@danielsotelo6753this is mechanic talk take a seat in the corner
How did you get those two bolts in the back to line up?
We're can I get that screwdriver thing, nothing pops up on Amazon ..
Zraupp10 QMET Plastic Fastener Remover Clip Removal Tool www.amazon.com/dp/B0734VKNYK/ref=cm_sw_r_cp_api_i_tWM6EbPRY5GCJ Is this what you where asking for?
In the link for the pulley extractor I see difference tool from the one you using,can you send the link for the tool you using?thanks
The tool I was using was purchased off of a Matco tool truck but the one in the link would work.
Can you rebuild them? I see they sell kits
I know you can buy reseal kits
Me personally, not sure how to rebuild a power steering pump.
how much is labor for re[lacing power steering pump ??
Zraupp10 it’s about 3hrs book time and whatever the shop rate would be.
@@diamondtruckperformance493 whats the model number on that tool ?
Snap-on tool #cj117b2 for the remover tool
Thank you.
Part number and brand name of the removal tool?
Matco tools part #mst4530
Sorry it took so long to reply.
How did you bleed the system when you were done?
I just fill the reservoir and turn the steering back and forth to max point and refill afterwards.
@@diamondtruckperformance493with the cap on or off
@@carlitosortiz2870 cap off is usually how I have the best luck, front wheels off the ground helps also. If it gets real foamy inside the reservoir I usually turn off the truck and let it sit and let the air come out of the system.
@@diamondtruckperformance493 thanks man
Way to much time wasted ,why pull pulley off on truck when you can do it on bench. No need to remove all those shields.
.