ABS light on dash/pump fault/how to repair ABS module motor/ABS module replacement + bleeding brakes
Vložit
- čas přidán 26. 04. 2021
- Hi,
This is a video showing how to fix and replace ABS pump, electric motor very often on this models stops to work and it's giving light on Dashboard.
thanks for watching
subscribe and share
I thought this took over 6 hour to replace on Prius 2nd gen 2004 to 2009 but you made this look so easily done.
Thankyou my friend.
Have to bleed my brakes today. Wish me luck
Hi,
I wish you all the best, and don't be worry, make sure you do in right order and you have always enough oil, than double check all nipples they are tight before you go drive and nothing to worry than.
Svaka čast meni se također pokavrio i nisam znao da se može reparirat morao sam kupit drugi polovni 300 eura al je trebao biti s istim serijskim brojevima
Hi thank you so much for this incredible video. Can I ask you, if my my brake like is completely empty due to a caliper failure. Do you think it will refill just by pumping the pedal and bleeding the caliper, or by pumping fluid from the caliper, up to the master cylinder?
Iam ur big fan sir my countries India
Merci très bonne vidéo
Mulțumesc pentru video, foarte bine făcut. Eu nu reușesc să scot mufa cablului, cum ai reușit?
Hello, can you ask, the motor of the ABS unit starts to work immediately when you turn the ignition key or when you press the brake?
I watch ur video, did u weld the one u cut from the housing of the motor to the housing unit of the ABS? Also what did you use to spray the spill’s brake fluids?
This what im thinking... how to close back?
Maybe it's out of context but is it possible to replace a single solenoid valve from the hydraulic block? If yes where I can find a repair kit?
Good work
Very interesting thanks for sharing
You are more than welcome :)
Mi VW POLO BAH 2008, frenos ok. No funciona km, velocímetro y cierre centralizado. Hay un sonido de motor eléctrico pequeño en el ABS q nunca se apaga, lo desconecte xq ese sonido es todo el día.
Aquí en LIMA, nadie los vende ni repara.
Alguna recomendación ?
Hello! Nice video, thank you! I have a question - how do you remove bearing and put it back?
Hi, I removed bearing because I didn't need to use motor again, on plastic behind made some damage, so if you wanna split it completely you gonna need to make a tool which goes nicely behind plastic to take all out together.
Thanks for watching
Hello how are you doing, quick question my vehicle has a compressor that is on the driver side and a modular on the passenger side how do I know if the compressor is working or not I can feel the motor on the passenger side
Will this make the steering wheel shake at 35mph ,I had stabili trak light come on & the next day everything was fine & now the problem came back today ,there is no stored codes.
Hello, thanks for the video ! Could you, please, tell me where can I buy new ABS pump online for my Ford Fiesta 1.4 TDCI 2012
Hi! I have a mk3 2011 Megane. How long does it take to remove the abs unit ? My autodata sez 9hrs but that doesn’t seem right, seems very long. Hopefully you can help and give me an idea of how long it takes to remove it.
Cheers
Did you get this done mate and how long did it take for it
Good Morning
Did you just change the electronics?
možda prehrabro zaključujem, ali poruka "U redu" na skeneru me navukla da se moguće radi o nekome s ovih prostora (definitivno ne bih to niti pomislio po engleskom u govoru i titlovima)....ništa posebno nemam za dopisati osim - fantastično ! Nemam (još) nikakvih problema sa ABS sustavom (Dacia Duster 1.5 dci), a koliko sam pročeprkao, imam isti modul. S obzirom da je pozicija modula iznad centralnog cilindra (slično kao i na vozilu u videu), moram li odzračivanje sustava (kod zamjene tekućine) odraditi preko OBD.a (skenera)? ...ili se to može odraditi kao na "klasičnim" sustavima ?
ma kupi novi abs polovno i onda neka ti ga elektricar podesi sa tvojom sasijom to jeste flashuje ja sam to radio u Kiseljaku. nisam mogo naci abs sa brojem koji meni odgovara i onda elektricar jedan ro podesio kad postave konektuju se na computer i to odrade.
how do you avoid the leaking of the brake fluid
I'm getting ABS lights on and 2 speed sensor errors along with power steering malfunction error. A test has shown 2 sensors are getting 9v, 2 are getting 12v. It's not the wiring from ABS to sensor. Is it likely to be this ABS Module? Ford Focus RS mk2
Pozdrav....meni je abs pobrljavio i majstor mi reče da mora da se zameni.I tom prilikom mi je rekao da je mehanički deo u pitanju jer mi neki put kad pritisnem pedalu ostane da koči...ne vraća ulje... uglavnom sad shvatih da mogu samo taj deo da zamenim.Ako bude drugačije oznake a ne starije proizvodnje samo da se ukodira?Hvala...
What diasnostic tools you use?
this video is unique
Merci
What make is your abs module please, so did you fit new brushes to the motor ? Thanks good video
Hi,
this module is Ate make, so on video you can see I open electric motor but there was damage on rotor. I had another module which I used so I just swapped my module ECU, mainly I opened it to see what happened, so brushes were like new, they make brushes holders too tight and brushes get stuck in there. So if you opening abs pump, just carefully open cover slowly come to brushes holders, spread it a bit and clean all, that's all what needs most of the time.
Thanks for watching
@@out_of_service5844 thanks very much good info, but i know it is an ate but which one? ! Mk70 ? Or may be another as the bits that hold the motor casing to the aluminum block are different to a mk70. Thanks i have mine out i really want to fix it my self because my fault is a bit intermittent ie if i hit the casing sometimes the abs light goes out and if it is out i can make the electric motor work with diagnostic equipment but when i do i can hear it running for about 4 sec then it stops and the abs light comes on and says unable to start motor and diag. Says pump is locked.
Some people replace the bearing and brushes themselves. So what should i do send the unit off and pay £260 to fix, rebuild or fix it myself? Thanks
@@antsfur hi,
What I would tell you, on video you can see it is not really big job to open it and fix it, you could do nearly the same way, press the aluminium away, than remove motor, than if motor is exact same as here you can drill two small hole so you could realese clips to open motor, don't very if you damage tiny bit plastic you can fit it back but use some silicon, than mainly take care while drilling not to go to far or to go on wrong spot, check for your pump type is there any photo on Google with open pump just to find position for drilling. Than you could replace brushes or you could clean it all and spread a bit brush sliders, for bearings I would say they are most of the time good.
In case this all sounds too complicated, try to see how much is second hand part, or send it for repair.
Hopefully you find this info useful
Thanks for watching
When you swapped the original ecu with new pump and block, should you have exactly the same pump number or it can be different?
what is the name of your diagnostic tool?
Hi,
Launch diagnostic tool, good for all brands.
Thanks for watching
Merhaba connect 2010 model aracımda abs ve esp isigi yanıyor tablette hata abs beyni devre hatasi veriyor
ABS is for a car?
I had removed motor assembly, but while removing bearing became damaged,please tell the size of bearing.
Hi, I'm sorry for late response. Unfortunately I don't have bearing size, but you could measure old one and source bearing locally to any shop specialist for bearings.
@@out_of_service5844 yes ,got it from local shop, thanks, your video saved my 73thousands rupees
But to bleed air from ABS module you need scanner?.
I buying a second hand abs module do the serial numbers have to be the same
your module is coded 4 your car, you will have to have it reset to work in car, the lights will stay on . make sure it's not the pump. there is a company that you can send them whole abs system and will have a 5 year warranty for 400 dollars not including shipping
How setting Abs please colt2007@@michaelclark8137
Troble code C2200?
thanks! but you seems murmur to yourself. Which part wrong and how did you fixed it?