Another very helpful video. A problem that I have had in the past is that I forget to release the parking brake when I am working down in the woods. I am in low range and in 4wd so the tractor has plenty of torque to move, even with the parking brake engaged. I have picked up a couple of warning lights to install in my dash. I believe that they will look like they came from the factory that way. It's About Making It, Not Buying It, Dave Knows How, and Paul Short all seem to have had the same problem and they each do a video on what they did to solve the problem. Dave Dobbs did his up with a back up alarm to alert him that the brake was still engaged. Thanks for sharing this. Very informative.
It should be similar but the spec for the amount of slop allowed in the clutch may be different. It certainly sounds like it needs adjusting! Thanks for watching!
Hello, sir, good afternoon, excuse me, can you make a video on how to remove and replace the clutch lining and the new rear wheel brake lining on the Kubota tractor, the L series, especially the L 3250, thank you very much, sir, sorry for using Google Translate
Hello Den! Sorry but I don’t have the tools or the skill for such a repair. If I have an issue like that, I would take it to my Kubota dealership. Good luck!
@@DIYMyWay Good morning, sir, I would like to ask if there is no UDT type oil for Kubota tractors, what is the equation for this L series tractor front axle oil, for SAE, how much do you use from the equation if you use another brand for this oil, thank you for your reply, sir
Hi Paul! I’d check the linkages from the pedal to the transmission to make sure there’s no brush or sticks impeding the movement. Look for grease zerks along the linkages. YOu can also disconnect the linkage where it disappears into the transmission. If the pedal moves freely, then you’ve got a problem inside the transmission. Good luck and Thanks for watching!
The throttle on the L2500 is different than the ones on the L3301 and L3901, so I don’t know. But I would follow the mechanism toward the engine and squirt WD40 here and there to see if anything loosens up. Thanks for watching!
If the clutch pedal is out of adjustment, then could it cause some speeds not to engage? I ask since my Kubota MX5000dt will roll (move) in first and second gear, but does not move when either in third or fourth gears. I do know that the last time my tractor was in the shop being serviced that they mentioned they adjusted the clutch pedal. Interestingly, when I look at the adjustment rod, the lock nut is is all the way at the top of the threaded part of the rod instead of being locked against the metal at the bottom.
Hi Steven! Yes, I think so. If the clutch is only lightly engaged, it may only be able to move the tractor in the lower gears. My guess is the clutch is incorrectly adjusted. Thanks for watching!
You are a great instructor, easy to follow, and precise instructions!
I appreciate that! Glad it was helpful!
Another very helpful video. A problem that I have had in the past is that I forget to release the parking brake when I am working down in the woods. I am in low range and in 4wd so the tractor has plenty of torque to move, even with the parking brake engaged. I have picked up a couple of warning lights to install in my dash. I believe that they will look like they came from the factory that way.
It's About Making It, Not Buying It, Dave Knows How, and Paul Short all seem to have had the same problem and they each do a video on what they did to solve the problem. Dave Dobbs did his up with a back up alarm to alert him that the brake was still engaged.
Thanks for sharing this. Very informative.
Sounds like a worth project, Gary! Thanks for watching!
Good video Martin! This should help Kubota owners to adjust and maintain their tractors for themselves. Have a good week my friend!
Thanks John! May you also have a most splendid week!
Great video.
Well produced and straight to the point, didnt need to skip anything.
Only shows how to adjust pedal travel ,not actual adjusting clutch!
Correct.
Great maintenance video Sir !!! Very nicely built clutch and brake systems !!! they have a lots of grease zerks !!! Cheers !!!
Thanks, Dave! Cheers!
@@DIYMyWay You video should be part of all maintenance book ( like a CD ). Cheers !!!
Thank you!
You're welcome! Thanks for watching!
That sure is a great tip i need to check my soon .
Thanks Arles! Yes I recommend you check them sooner rather than later. I was surprised how far out of spec my brakes were. Thanks for watching!
The video was informative and great to watch! solid job!
Thank you, John! I appreciate your kind words!
How's she goin'? These videos will be great reference for Kubota owners!!! Great idea to post!! Take care!!!
Hi Mike! That’s the idea! Thanks for watching!
Hey Martin! Great demo and camera work! I need to tighten my brake on my BX! Its way out of tolerance! Thanks again!
Thank you, Jay! I hope your BX brakes are as easy to adjust as mine were!
@@DIYMyWay It stops... for now LOL
My adjustment rods are not under the tractor. They run vertical in the cab. 3500 series
Your videos are amazing thanks.
Thank you, Jimmy! I really appreciate it! Please tell all of your friends that might be interested.
Great videos
Glad you think so! Thanks for watching!
Good video I have a L2500 kubota ....do I adjust it the same. ( clutch ). When I push clutch in the tractor wants to keep going forward........
It should be similar but the spec for the amount of slop allowed in the clutch may be different. It certainly sounds like it needs adjusting! Thanks for watching!
Martin, great video. I wanted to point out that on the L3901DT it has a dual stage clutch and to adjust it is a little different.
Thanks, MD H! Makes sense to me. Thanks for watching!
I am looking for information to correct a problem with brakes binding up on aM4800 4 wheel drive tractor. 2009 model,820 hrs.
I hope you find it, Danny! Thanks for watching!
Hello, sir, good afternoon, excuse me, can you make a video on how to remove and replace the clutch lining and the new rear wheel brake lining on the Kubota tractor, the L series, especially the L 3250, thank you very much, sir, sorry for using Google Translate
Hello Den! Sorry but I don’t have the tools or the skill for such a repair. If I have an issue like that, I would take it to my Kubota dealership. Good luck!
@@DIYMyWay thank you sir for the reply good luck always
@@DIYMyWay Good morning, sir, I would like to ask if there is no UDT type oil for Kubota tractors, what is the equation for this L series tractor front axle oil, for SAE, how much do you use from the equation if you use another brand for this oil, thank you for your reply, sir
What camera and software are you using? Nice video!!!
I use Corel Video Studio Ultimate on a Windows 10 laptop. Thanks for watching!
@@DIYMyWay Thank you!
Gary, do you think the L2501 would pull the rcr1860 brush cutter? Thanks
HI, I Have a 2013, L4600 HST. Speed control pedal sticks. I see no grease fitting. What is the fix for pedal to come back to neutral position?
Hi Paul! I’d check the linkages from the pedal to the transmission to make sure there’s no brush or sticks impeding the movement. Look for grease zerks along the linkages. YOu can also disconnect the linkage where it disappears into the transmission. If the pedal moves freely, then you’ve got a problem inside the transmission. Good luck and Thanks for watching!
Hi I have a L2500 kubota I was wondering how do I make the leaver on turtle & rabbit move easier it is hard to move
Thanks Rick
The throttle on the L2500 is different than the ones on the L3301 and L3901, so I don’t know. But I would follow the mechanism toward the engine and squirt WD40 here and there to see if anything loosens up. Thanks for watching!
@@DIYMyWay thanks I will do that first.....thank you very much .....Rick
The wd40 worked great thanks so much.....keep up the good work
Rick
I have a problem with my Kubota bx23, there is no power in the tires.
Sorry to hear that! I have no experience with the BX series tractors. Good luck!
If the clutch pedal is out of adjustment, then could it cause some speeds not to engage? I ask since my Kubota MX5000dt will roll (move) in first and second gear, but does not move when either in third or fourth gears. I do know that the last time my tractor was in the shop being serviced that they mentioned they adjusted the clutch pedal. Interestingly, when I look at the adjustment rod, the lock nut is is all the way at the top of the threaded part of the rod instead of being locked against the metal at the bottom.
Hi Steven! Yes, I think so. If the clutch is only lightly engaged, it may only be able to move the tractor in the lower gears. My guess is the clutch is incorrectly adjusted. Thanks for watching!
@@DIYMyWay Thanks for the quick reply.
Are the instructions in this video pertinent to a Kubota B4200? Thanks!
Hi Edward! I imagine it’s a similar process but not exactly the same because the B4200 is not part of the L series tractors. Thanks for watching!