Honestly wasn't that hard, worst part was forgetting to get a 27mm socket beforehand and having to leave to get one. Get an extension for the 27mm socket too 😅
@@Nonx47 i saw someone mounting the perrin up with the AOS so it should work, but i heard the perrin wont clear the cobb intercooler if you want that. might clear the ETS intercooler though
Question, my car is almost at the expiration of factory warranty… I want to add the AOS .. does it matter if your running synthetic oil install AOS then go to a 5w30 oil ?
This looks identical the the Legacy/Outback XT. Does the custom bracket for the canister line up on the L/OB XT suspension mounts also? Also I heard these are bad for any climates where winters reach freezing temperatures.
We have had a few clients make a custom bracket and use the system on Legacy/Outback XT. Any PCV system (even the OEM system) is prone to freezing of condensation in the system in extreme negative temperatures. The line to keep an eye on is the AOS drain hose. This is the hose that allows separated oil to drain back into the system. As long as the vehicle is warmed up before driving and not exposed to constant negative temperatures while not running it will not be an issue. In extreme cases the oil could back up, but the 1 liter volume of the can effectively covers any temporary backup situations.
Like the OEM PCV system, the hoses may be plugged by frozen condensation in extreme cold. (Negative Temps) The hoses are not going to tear from this. Always allow your vehicle to fully warm up and keep it garaged in these kinds of temps to avoid any issues. Again, this is no different than the OEM PCV system in that aspect.
It would be best to consult with your dealer regarding warranty questions. However, the dealer is not able to completely void your warranty. The dealer must prove that your modification caused the failure in order to deny coverage.
does it make any sense to direct the acidic micro carbons vapors from the crankcase and reintroduce these contaminates into the unfilter air flow and fly back into the combustion's chamber to mix with the combustion cocktail and then on toward the oxygen sensors and out into the converter to build up and cause the ECM to pump out more fuel into the fuel injection process? BTW I do not want to create lots of back pressure to blow out the cheap seals and gaskets that mfgs enbrace!
The OEM PCV system recirculates these gasses back in to the intake stream unfiltered as well. However, with the OEM system you also get all of the aerosolized oil being recirculated as well. This system allows that oil to drop out of suspension while maintaining the function of the PCV system.
The written instructions on our site include a complete tool list. www.iagperformance.com/content/instructions/IAG/IAG-ENG-7183/ss-aos-22-wrx-instructions.pdf
This install looks tough! Might have to use some PTO lol
Honestly wasn't that hard, worst part was forgetting to get a 27mm socket beforehand and having to leave to get one. Get an extension for the 27mm socket too 😅
Excellent follow along video, almost as good as written directions...but nobody believes in hard copy no moe!!
Looking at how this is set up looks like ima have to not use my Perrin strut tower bar??
got it installed, love it a lot, need to do some searching to find a strut bar to work with it
Any idea what will work with it? Seems like the Perrin has the clearance but I'm not sure
@@Nonx47 i saw someone mounting the perrin up with the AOS so it should work, but i heard the perrin wont clear the cobb intercooler if you want that. might clear the ETS intercooler though
The last step “ Bleed the coolant” the coolant is not bleeding what’s the sign?😢
Question, my car is almost at the expiration of factory warranty… I want to add the AOS .. does it matter if your running synthetic oil install AOS then go to a 5w30 oil ?
The oil type doesn't matter for the AOS, but you will want to run an oil which is compatible with DI engines.
@@theiagchannel I’m driving a 23 wrx limited
Will this system work on my N/A 2.5 ice engine, without blowing the seals out?
Would you install one for me??👍🏻
Great install video even though it’s a pain to do
This looks identical the the Legacy/Outback XT. Does the custom bracket for the canister line up on the L/OB XT suspension mounts also? Also I heard these are bad for any climates where winters reach freezing temperatures.
We have had a few clients make a custom bracket and use the system on Legacy/Outback XT. Any PCV system (even the OEM system) is prone to freezing of condensation in the system in extreme negative temperatures. The line to keep an eye on is the AOS drain hose. This is the hose that allows separated oil to drain back into the system. As long as the vehicle is warmed up before driving and not exposed to constant negative temperatures while not running it will not be an issue. In extreme cases the oil could back up, but the 1 liter volume of the can effectively covers any temporary backup situations.
How dose it hold up in the far north climate, worried about condensation freezing in the cup or possibly hoses and splitting them ?
Like the OEM PCV system, the hoses may be plugged by frozen condensation in extreme cold. (Negative Temps) The hoses are not going to tear from this. Always allow your vehicle to fully warm up and keep it garaged in these kinds of temps to avoid any issues. Again, this is no different than the OEM PCV system in that aspect.
does this help with carbon build up?
Yes, this will prevent oil from entering the intake and coating the back of the valves, which leads to carbon deposits.
Will this work on the Ascent?
It can be made to work on an Ascent or Outback XT with a custom bracket.
Does this void any warranties?
It would be best to consult with your dealer regarding warranty questions. However, the dealer is not able to completely void your warranty. The dealer must prove that your modification caused the failure in order to deny coverage.
Does the addition of this require retuning the engine? Tryna add mods that work with the stock tune first. thanks
No tuning required!
Wheres is the fa24 longblock coming out?
We're working on FA24 Short Block development now
got mine green and i love it thank you so much ill be doing a facebook and ig live review when install
Can't wait to see it!
does it make any sense to direct the acidic micro carbons vapors from the crankcase and reintroduce these contaminates into the unfilter air flow and fly back into the combustion's chamber to mix with the combustion cocktail and then on toward the oxygen sensors and out into the converter to build up and cause the ECM to pump out more fuel into the fuel injection process? BTW I do not want to create lots of back pressure to blow out the cheap seals and gaskets that mfgs enbrace!
The OEM PCV system recirculates these gasses back in to the intake stream unfiltered as well. However, with the OEM system you also get all of the aerosolized oil being recirculated as well. This system allows that oil to drop out of suspension while maintaining the function of the PCV system.
Do you have any a/o separators for the type r?
Sorry, not at this time.
Thank you for your response. 🙏🏼I really believe you have a quality product and hope you could extend your line to the type r
Is there a list of tools needed anywhere handy? Saw one person mention they got halfway through before realizing they had no 27mm socket
The written instructions on our site include a complete tool list. www.iagperformance.com/content/instructions/IAG/IAG-ENG-7183/ss-aos-22-wrx-instructions.pdf
@@theiagchannel thank you! I must have missed that when I purchased
What’s the torque spec for the pcv fitting?