VW Beetle Rear Brakes and Axle Seals! Getting There!
Vložit
- čas přidán 12. 09. 2020
- VW Beetle Rear Brake replacement and Axle seal replacement How To. Also CV joint removal.
Hi Everyone! In this 1969 VW Beetle episode, we are replacing the rear brakes and also replacing the transaxle shaft oil seals. With the bearings finished in the last episode we can start to move forward. We use that cool torque multiplier to set the hub nuts to 225 Ft-lbs! :)
Enjoy!
#vwbeetle #classicbeetle #beetlebrakerepair
The VW Torque Multiplier too for rear-wheel nut: amzn.to/3besSiq
The Ring Plier kit: amzn.to/3gDDw33
The Star/Triple Square/Spline Drive toolset: amzn.to/31DUHxk
Seal Puller: amzn.to/2EPxT4y
Rubber Mallet: amzn.to/2ENIBJ6
Help support our channel and become a patron:
/ heidiandfrannysgarage
For Correspondence:
Heidi and Franny's Garage
P.O. Box 740487
Arvada, CO 80006
T-shirts and other clothing:
Merchandise:/heidiandfranny.storenvy.com/
Amazon Store Page
www.amazon.com/shop/heidiandf...
Facebook Page: / heidi-and-frannys-gara...
Instagram: heidiandfra...
Twitter: / heidifranny
Website: www.heidiandfrannysgarage.com
The Cameras and Equipment we use:
Main Shooter:
Panasonic Lumix G85 (goo.gl/geSFpN)
Main Shooter Lens: (goo.gl/RsHkkF)
Main Shooter Microphone:
Rode RodeLink FM Wireless Filmmaker System
goo.gl/aQsmrg
Car Cameras:
Sony FDR-X3000 (goo.gl/P6XdYZ)
GoPro Hero 7 black (amzn.to/3dph4cB)
Car Mounts:
Fat Gecko Camera and Camcorder Mount (goo.gl/zqCHvT)
Fat Gecko Camera Mount (goo.gl/AXQAr6)
Fat Gecko Mount (goo.gl/RhyXYT)
Drone:
DJI Mavic Pro and Kit (goo.gl/jQbk9V)
Stabilizer for mobile phones and action cams:
DJI Phone Camera Gimbal OSMO MOBILE, Black (goo.gl/Acr1jg)
Disclaimer:
Due to factors beyond the control of “Heidi and Franny’s Garage”, We cannot guarantee against improper use or unauthorized modifications of this information. “Heidi and Franny’s Garage” assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. “Heidi and Franny’s Garage”recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of “Heidi and Franny’s Garage”, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not “Heidi and Franny’s Garage”.
Music provided by Artlist.io
Music in bumper provided by:
BACK IN SUMMER by Nicolai Heidlas Music / nicolai-heidlas
Creative Commons - Attribution 3.0 Unported- CC BY 3.0
creativecommons.org/licenses/b...
Music provided by Audio Library • Video
Hat's worn by Heidi and Franny provided by: www.Fabkittenhats.com
Automotive and Car Channel - How To (DIY):
Porsche, Ferrari, MINI, General Car Maintenance - Auta a dopravní prostředky
Hi Everyone! In this 1969 VW Beetle episode, we are replacing the rear brakes and also replacing the transaxle shaft oil seals. With the bearings finished in the last episode we can start to move forward. We use that cool torque multiplier to set the hub nuts to 225 Ft-lbs! :)
Enjoy!
Tools used:
The VW Torque Multiplier too for rear-wheel nut: amzn.to/3besSiq
The Ring Plier kit: amzn.to/3gDDw33
The Star/Triple Square/Spline Drive toolset: amzn.to/31DUHxk
Seal Puller: amzn.to/2EPxT4y
Rubber Mallet: amzn.to/2ENIBJ6
I imagine there is a lot of thought and effort that goes into the production of one of your videos, I really appreciate your commitment to quality and excellence.
Thanks so much for that. Yes... 35-40 hours of work...
AXLE NUT AND FLYWHEEL TOOL IS MAN'S BEST INVENTION EVER
Nicely done. That torque converter tool is really nice
I wonder if there's any place to rent one from, 'cause I'm sure kuhl tool = $$$.
Mark Stach they’re close to $100; if you have a VW it’s worth it to buy it. Every time the rear brakes need to get done those castle nuts need to be removed and reinstalled. Also works for the flywheel.
Your depth of knowledge is incredible, and clarity is appreciated. Thanks.
Hello! I'm from Brazil. Today I had the pleasure of knowing your channel. I'm delighted. I love the way you explain and your knowledge about. The organization and the workshop so clean. That's good work. Congratulations 🎊
This is sooo good. I bought my wife a beetle and this channel is the best by far! I'm a Suzuki mightyboy guy but am loving working her beetle thanks to this channel
I can honestly saw you have some awesome repair videos. Thanks so much for your time and these videos. Really helps out those of us who aren't super beetle mechanics. 👍
These Beetle episodes make me want one... I saw a gorgeous mid-60s metallic blue Beetle the other day. It was a Coupé (not cabrio) but man did it look fun. And knowing you have these amazing video guides would inspire a great deal of confidence in that kind of purchase ;-)
I know... I'm a terrible influence ;)
Thanks for giving your time to vlogging the process and also comparing cost of new ones (CV & axle ) verses the time to clean the original.
Another fine "how to" video! The attention to detail in your editing is awesome!
Thanks so much!
Excellent videos, so clear and concise. I appreciate your attention to cleaning parts before assembly. I have a 1974 Beetle entirely disassembled right now, will be going back together this spring and summer. A tip I learned working in the auto service industry for 25 years. Pack the channel on the backside of seals with grease. Sometimes when pressing/hammering a seal in, the spring that keeps the lip pressed against the shaft can pop out and then it won't seal properly. Not to mention the rogue spring! The small amount of grease won't contaminate the gear oil to any appreciable degree. I will certainly be revisiting your Beetle videos as I begin putting things back together!
Thanks for the tip!
Lemon sure is lucky to have a good doctor like Franny.
Thank you so much for these videos. I have the same 69 convertible (in much worse shape) and my retirement gift to myself will be to rebuild it.
I just bought all the bits for a full brake rebuild. You do an amazing job detailing exactly what needs to be done.
Thanks! Next video is the adjusting and bleeding :)
Great job. Nice contrast between the VW and the I8 parked outside. Technology sure has come a long way. Looking forward to the 3.2 new interior and gearbox :)
It is amazing the difference. Both cars, but that is about it. The Beetle does have one more cylinder though ;) I hope all is well.
$80 per driveshaft assembly! I miss having a Type 1.
Thank U so much, I've always loved beetles since ma young age, am a poor guy who loves class and attention, U can't believe that I even bought the radio, speakers and seat covers b4 even buying it, it took me long to decide and buy one but since I've got this tutorial from U, I'm confident I can do most of the work ma self, am buying it soon, I love the beetle and all ma old friends know it
Superb work, beautifully shot, and with boundless enthusiasm, thank you Franny.
Thanks so much!!
I love your videos, Franny!! You’re so detailed. Great channel!!
Thank you so much!
Great video Franny!
Heehee, yep, I remember finding those different bleed nipple spanner sizes on 2x Beetles and 2x T2 vans I had way back.
Great work Franny - can’t wait for the next video on lemon drop 😍
Coming soon!
You two are the best!!! Make things look so easy!!!
Thanks!! I need to get caught up on your i8 adventures! You got your car back? I hope all is well :)
Heidi and Franny's Garage hi! No they said they are having trouble programming the new SME unit. Smh. In the meantime we drove to myrtle beach for three days so I’m not even going to stress it or make a video about it. Lol “they still have my car” won’t be a title this week! Lol what I should get next videos on the way! I would double back next year and buy a 2019 roadster under WARRANTY!
Impressive Attention to Detail in all your work. Appreciate the education.
Thanks!
Awesome video as always, putting new CV / axels is a wise decision; you never know how they’ll work out, if you’re refurbishing it yourself, until you drive the car!! Best from Monsoon Naples.
Thanks! I think they will be sweet. I was looking at the Pier webcam today and it looked a bit cloudy and rainy... That time of year I suppose...
Heidi! Franny! Great channel. I'm sure my viewers will love your videos and I've made you guys a featured channel. Keep the amazing content comin'....
Thanks Ian. Looks like you have done some cool stuff.
Very informative and a pleasure to watch, thank you and regards from down under
Glad you enjoyed it! Thanks!
As a painter I think I would have painted the raw cast iron brake drums to keep them from rusting. Just a thought. I really enjoy your vids!
Thanks Mam noice watch your work on vw 1969 it's a clean Job in future I will wait'g to more of this infact I also have a vw 1969
Thanks for another great video 😎
Great to see that you had some help from the mechanics most useful tool - the third hand @7:30 :)
That's creepy huh? I'm going to have to have a talk with that editor ;)
Great video as always, Heidi and Franny! One suggestion - if you use a stick of some sort and depress the brake pedal an inch or so before breaking the braking system loose it will keep the fluid from continuously peeing out.
That's a great idea! Thanks!
Ooh gotta have that super cool tool!,,☺
I also agree and reccomend that you removing the Brake bleeder helps. They went to 8mm for the bleeder to make it easier to open/close.
However when reinstalling the brake cylinder I always screw in the brake line first with the mounting bolt only loose. Once the brake line bottoms, tighten the mounting bolt. Then tighen the brake line.
Great job and very educational I did notice you keep calling the break shoes Pads they are actually called Shoes Pads are for Disk breaks and shoes are for drum breaks and your car is equipped with drum breaks no big deal love your videos
The bolts are XZN. I use a Hazet 8808 - 8LG so the head of the ratchet isn't interfering with the dust boot. The cross section of the large circlip isn't the same on the inside and outside. Make sure the rectangle portion is to the outside. I always grease the inside of the seals, not just the outside of the parts rotating in them. I enjoyed the video. Thanks.
Great video.
Great video! Thank you 😊
Super informative. Thank you
Hi Heidi & Franny will you consider doing a full engine gasket on a 1500 VW engine ? I consider your CZcams Chanel is the best in VW DYI .I have a 68 sunroof VW beetle . Keep up the great work .
Great video. I’m about to do my CVs. $80 for the entire assembled set is crazy cheap. Here in Australia, I just paid $600 for just the assembled CVs (4 of them). Including boots, grease, etc. only thing is removing the existing ones from the Beetle and fitting them to the existing shaft after the messy job of packing them. These ones I got are made in Germany. But what a difference in price.
It is crazy how cheap they are. I wonder why the big difference. I just filmed the install and it still takes a bit of time to install them, keep the clean bit clean and the greasy bit greasy and then torque all the bolts.
Heidi and Franny's Garage insane. Even with exchange rates and shipping, a fully assembled shaft with all the trimmings here, the price isn’t justified. But the only other option is Chinese, and I’ve experienced the pinnacle of their metallurgy... no thank you, it’s safer using Camembert Cheese.
Thank you for your expertise and tips. I’ll be wire wheeling the existing shafts and probably giving them a little coat of primer and then black heat resistant paint. Then I’ll pack the new CVs and fit them to the shafts and cover them in fresh ziplock bags.
Would you recommend added a clamp around the boots once you have them fitted? The kit I received didn’t come with any, and I kind of assume the little raised sections on the shaft where the small end of the boot sits kind of slides over that and sits there.
That is a great question! The owner picked up a set of boots and such from a local parts place (we thought we would be able to just rebuild) and I ended up talking with the sales guy about that. He said they never put on a clip on the axle. I was like, Really?? I always have. He said I could use a zip tie! I went ahead and bought a set of clips and wouldn't you know, when the owner arrived with the parts the sales guy threw in four axle clips ;) Thought so... The full axle kits have clips on the axle as well so I would suggest to install them. You don't want hot grease dripping (or flinging) out the end of the boot ;)
Heidi and Franny's Garage thank you for confirming that. It seems some local VW folks around here are of two minds about the clips too. On this current beetle I’m mechanically restoring, they don’t have any clips. But I might throw some on. It can’t hurt.
Franny, you make it look so easy but I know from experience it isn't. The best to hope for is a job without significant problems and no surprises when you take everything apart. I love the torque multiplier tool and I'm considering getting one. I have to stand on the torque wrench handle when torquing wheel hub nuts.
I'm looking forward to seeing the CV axle install! I recently installed two on the rear end of my SUV, and I basically had to hammer on them to get them to go into the differential. They won't go back into place even with a coating of differential fluid and a bit of grease to keep the C ring from moving out of place.
One thing that amazes me is the use of c-clips, snap rings, and cotter pins. They are the safety hardware that is the last line of defense against a nut coming loose, a bearing from wiggling out, or a pin slipping out of its hole. They are all so tiny but so very important. They're used on everything from ball joints to turbos. I think about what they do and I'm in awe.
The axle install is coming up. It went well. Sorry you had so much trouble. usually it is more of an access issue for me. I think I change my method every time I do one ;)
@@HeidiandFranny I'm looking forward to it! Glad it went well.
I have 2 front CV axles left to replace. I did the rear end first because it was making noise and clunking, and felt very unstable. There were a lot of problems back there. All the suspension was completely worn out. The front isn't much better but it has more parts so more redundancy before it fails. The axles aren't easy to get to normally, but I will have all the suspension parts removed and the axles will be easily accessible.
I like your shows
That torque leverage tool is awesome!! There doesn't seem to be versions of it for other cars though. I wonder why. It'd have been useful to remove the axle nuts on my LEAF. They're supposed to be only 135 ft-lbs but the doofuses at the dealer got to them at one point and they were tightened to what felt like a bazillion ft-lbs!
That is always so annoying... I wish they did make it for other cars. I actually bent a cheater pipe on the 911 and it was probably four feet long!
Brilliant again. It just keeps getting better. Always a problem, do I buy all the tools or adapt and overcome? 🤓🇬🇧👍🏻
I want the episodes to never end lol.
“This episode is getting long in the tooth”
No, ahhh lol
So glad you liked it :) Thanks!
Your channel is bound to keep growing. Keep up the good work.
I have a VW Van and Lemon Drop has been helpful (not everything’s directly transferable but close enough)
Franny, I know you love doing auto-mechanical work, just hope you are well compensated. Another great video “Thanks”.
Well, I only loose a little on every car, but I make it up in volume!
Heidi and Franny's Garage , Your style and sense of humor is great. Thank you again for sharing your mechanical adventures and special kudos to Heidi for her cinematography
Excellent video! Great quality and editing as previously mentioned. That car is in mint condition, has it been restored? Thank you!
Nice job 👍
Thanks 👍
Drum brakes have brake shoes not pads.
Easy to get them mixed up too 😉
That darn lysdexia...
Do you happen to know the official color of lemon drop? Just bought 71 super beetle that is canary yellow. I want a softer chiffon yellow like lemon drop. Great videos, you di an incredible job and I am grateful for your expertise! Merry Christmas!
Great video! You covered everything. Smart choice on the cv joint axle assembly. Years back the only option was to rebuild to save money but, now they are affordable as a complete unit. How did you not get transaxle oil in your hair as it was dripping? 😅
LOL! I think I might have... ;)
@@HeidiandFranny Where did you find the whole assemblies for $80, I can't find them :(
Looking great! Maybe it’d be a good idea to spray paint the new drums to prevent corrosion?
I was wondering about that. They look like they will stay clean for quite a while. No rust anywhere...
I always put a little anti-sleaze on my breakover bar.
Haha! I caught that, too!
Thanks for the excellent video Franny. Where did get all your mechanical knowledge from, are you an Engineer by trade. ? Also, your model plans are amazing. Cheers
I am... ASE. Although I haven't worked in the field for quite some time... Glad you like the RC airplanes :) It was something I did with my Day (who was an airline pilot UAL)
Where did you get the complete CV axles
Rats! I was really looking forward to the greasy-grimy repacking of the CV joints, but can’t argue with that replacement cost, assuming they are good.
I've done that a couple times and it is super messy. I'll add a bit in the next video if I have time on the disassembly and assembly of the joints. That is actually the fun bit!
Hi, great video. Can you provide a link for the axle seals? Having a hard time finding them.
It has been a few years but I think I got the parts from Cip1. Have you checked there?
Watching your video reminds me how much I dislike drum brakes.
They are pretty fussy... I think the worst part is they need constant adjusting and if the cylinders leak it ruins the pads.
Where did you get your lovely yellow toolbox
Thanks, Harbor Freight of all places. This sort of thing id perfect from HF. It has been great actually. The drawers nice and sturdy and smooth. Can't beat it for the price.
Any idea where I might be able to find a the brake spanner clip? The little clip that hooks onto the upper spring, as seen at 7:25. I'm missing one on one of our Speedsters...
Hi there!! I hope all is well :) Hmmm... I wonder if Stoddard would have that. They do have a bunch of brake parts. I found this on Cip1:
www2.cip1.com/c24-113-609-625-pr/
I hope that helps :) Franny
@@HeidiandFranny OMG, you're the BEST!!! That's exactly it. Thank you so much 😘
where did you find the assemblies for $80 ??? Can you post the link please??
Hi Pete, The owner provide the parts, but I think he either used Cl1 or Jbug. CP1 has them for ~$120.
How you get the tools to the job or where can I order the tools ??
Hi, the links for the tools are in the description. Thanks for watching!
12:40 when you get that nut “ya zoo” tight......the big cotter pin will fit....you can’t really go passed the slot for it. You will break the nut.
So essentially, if you have it on the ground with a big breaker bar.....when it stops turning it will be in the correct place to put the cotter pin.
There are only 3 places...I think.....the key can go. Neat-o huh? Those Germans were smart.
All bets off if the parts came in a blister pack with the words “ empi” printed on them.
Worn cv joints make nice pen/pencil holders. Also nice little puzzle for kids to mess around with.
LOL! They are great fun :)
Where do you get your parts?
For the beetle? It depends.
Your 4 post lift is shaking (around 14 minutes) and it looks unstable. Is that normal?
Yes, normal for one that not bolted down. Yes, very stable.
Heidi and Franny's Garage I am glad to hear that. I just wanted to make it sure of your safety. Thanks
👍
Use brake part grease
Franny works fast. Probably fast enough to beat flat rate. Thus, a colorful sobriquet: Flat Rate Franny. Were she a mechanic and not an engineer, of course.
Bend both sides of the cotter pin! I didn't do that once, and the bent side of the pin broke off...and the whole pin slipped out. Not good.
You had a brand new pin break when you bent it for the first time? Never seen that...
@@HeidiandFranny me neither. That's why I always bend both arms on cotter pins.
Brake lube works a lot better than anti-seize it also doesn’t spread as easy.
Like the channel I like to see to gal's that aren't afared to get dirty and are pretty darn handy. I will learn thinks form watch this channel too. I am a car person as well and I got a suggestion. I see your using the old style jack stands which works fine. But you gal's should check out the Powerbuilt 6000lb. unijacks theere much better and safer. There a jack stand floor jack and bottel jack all in one for about $65.00 a peace $130.00 for a set not too much money and are great and much safer then the old jack stands. Been using my for 2 years now and are great. Got mine at Pep Boys. Google them and and find them lots of places. Much better and safer.
Thanks Matt, I actually have one! I was super excited to use it, but it won't fit under any of the cars :( It is a great solution because so many cars only have one jack point so where do you put the jack stand?? Those as you mentioned solve that issue. I just need to find one that is low enough to go under the car.
@@HeidiandFranny
That's a bummer but there nice jack stands.
It’s called anti-seize it says right on the bottle. 😂
Says you’ll never know the exact work then proceeds to calculate the exact torque she’s going to set. Commonsense flies straight out the window a few times in this video.
A breakover bar 🤣 I guarantee you’ll never see a breaker bar sold as a break over bar. Almost seems like you intentionally call stuff by the wrong name.