Thank you for everything you do I have a question and I would be very grateful if you could answer me In the large black capacitor, I get 311 volts, you said it should be 320 to 340, is the lower voltage in my case causing it to malfunction?
The test on the compressor is okay (the resistance between all 3 contacts is the same), also on the inverter board everything looks okay but the compressor still does not work
Hello sir...I have problem with my inverter double door freezer the indictor light is show but the compressor can not start at all I have the picture of the panel how I can show it to you pls
Hi Coul I replace a defective Embraco VCC3 2456 80F 14 Imput 220-240V 2.1A Output 230V 53 a 133Hz 3.3A for a similar one, but instead of 53 a 133hz, it is to 150? New one avalable is Embraco VCC3 2456 28 A 19 Imput 220-240V 2.1A Output 230V 53 a 115Hz 3.3A.
@@forevertechenglish What I discovered after purchasing the board is that it is not enough for them to have the same input and output values, we need to know whether the board is "drop in" or "Frequency". In this case, I purchased a "drop in" inverter board and the compressor did not start.
Thanks for your clear explanation .
thanks very much sir for sharing...God bless.
Excellent work thanks
Thank you too!
Thank You
You're welcome
Thanks
thaks for this video,sir
Most welcome
What if no voltage in UVW what is the possible problem?
Then, its possible any Igbt is bad, Or any thing around the circuit is bad, which need to be checked and addressed.
I would he very happy if you could explain how we run the Cf02d01 Ves motor board
Dear Sirs, I have a problem with my refrigerator inverter, blinking 9 times. Can you explain about Jiaxipera inverter circuit?
If I get one sure I will explain.
Hello sir,
What type of starter is used in the VCC3 2456 PL F 08 compressor?
Thank you for everything you do
I have a question and I would be very grateful if you could answer me
In the large black capacitor, I get 311 volts, you said it should be 320 to 340, is the lower voltage in my case causing it to malfunction?
311 are also fine. Its no issue. What the problem with yours?
The test on the compressor is okay (the resistance between all 3 contacts is the same), also on the inverter board everything looks okay but the compressor still does not work
l still looking for a solution. Thank you for your quick reply
Removed from working fridge did your jumper trick 1&2 but I use 120vac and it will not work. Great video but my luck is terrible
Hello sir...I have problem with my inverter double door freezer the indictor light is show but the compressor can not start at all I have the picture of the panel how I can show it to you pls
how to made refrigerator deep freeze copper pipe coil roll
Hi
Coul I replace a defective Embraco VCC3 2456 80F 14 Imput 220-240V 2.1A Output 230V 53 a 133Hz 3.3A for a similar one, but instead of 53 a 133hz, it is to 150?
New one avalable is Embraco VCC3 2456 28 A 19 Imput 220-240V 2.1A Output 230V 53 a 115Hz 3.3A.
For that check the hertz on your compressor, The lowest and the max hertz. If is in between the replacement board. You can replace it.
@@forevertechenglish thank you very much! Compressor is 53TO133Hz, inside. Very usefull you vídeo! Congratulations from Brazil!
@@forevertechenglish What I discovered after purchasing the board is that it is not enough for them to have the same input and output values, we need to know whether the board is "drop in" or "Frequency". In this case, I purchased a "drop in" inverter board and the compressor did not start.
Ciao, che valore ha il fusibile collegato dopo agli IGBT?
hi i am not get 320 v dc on capacitor
Are the follow up video posted?
Yep visit my channel I have them
الترجمه بالعربي كبيره جدا ومش ظاهرة الكارته وانت تشرح انقص حجم الترجمة حتي نشوف الشرح على البورد الإلكترونية
السلام عليكم
حجم الخط تستطيع التحكم فيه من الاعدادات عندك
this video toking to you hindi dubbing dir please 🥺
🫡