SAAAMMMEEE, was having so many issues tuning my nitro rs4 3 evo+ with the T3.0. The G3.0 is basically the same engine to my knowledge so this was still suuupppeerr helpful!
hello. hpi. ilove your cars and im glad for this tutorial because my car is old and needs to be fixed. but where i live i cant go to a shop and tune my car. hopefully my car can survive for muself to enjoy it while it lasts
Almost like the original 1993 Team Associated instruction video, but with actually useful cinematography, instructions, voiceover, audio, and illustration.
Nicely done. I have a t 15 and can't get it to stop dying when throttled. Idles great. Starts right up. The base settings described in the manual are not the same as the T 30 you demonstrated. Got me a new T 30 to drop in if I don't get the issue solved. Anyone with an idea please post.
You only have to break in 1 time but I would recommend using about 7 tanks to make sure u bucket is fine because some people don't 7 tamks amd the people that do use 7 tanks to break. In usually find there bullet is quicker
no you only have to breakit in once.. but you do have to tune it depending on the weather..the only time you have to breakin a engine is if you replace any of the internal parts like th pistonhead or the sleeve
I'm having problems with my nitro traxxas slash trx 3.3, I dont really know how to tune it, it stalls in the beginning, even when warmed up, then it takes off bit shuts off when I apply brakes
Hi. I have a tamiya tgs running the HSP 18 Nitro Engine 2.74cc. Have installed the engine. When the engine starts up the all four wheels starts spinning. Can’t get the idle settings or tunning setting right. Please tell me what can I do and how.
The new hpi bullet nitro st does not have a low speed needle but if u watch this vid u will get the hang of it . My bullet is ssooooo quick it was a great buy and it is well worth the money but make sure u get nitro ones thay r the best
Yes, the general tips will work for you car but as for tuning, always refer to your manual. Since this video is not of your brand of car, do not rely on this video, just use the procedures in this video as tips and always refer to your manual for detailed instructions. As for breaking in, use the directions in your manual as different companies use different techniques.
So I have an HPI nitro MT2 from way back before the 2009 models. I need a new needle bearing and a new bottom plate. The MT2 was discontinued ages ago. It feels like I had no hope.
The Chassis for the MT2 is: www.hpiracing.com/en/part/73946 It is still available. There are very few left however and we will not be restocking when they are gone. You can find details of all the Distributors currently signed on here: www.hpiracing.com/distributors The needle roller bearings are discontinued. But I know brands like Kyosho also used them under the number LD70. I believe you could also use two 5x8x2.5 ballrace bearings instead.
I have an eco rush. At idle it keeps moving forward and I have to keep the brake on, the throttle dial on the controller is low. I then adjusted the high speed needle and when I start it, it accelerates and burns through the fuel quick. Help!
Breaking in is easy, you need to read less and play more I usually on all my cars trucks no mattet what instructions say I run 1 tank on idle, then 2 and 3 tanks of gentle throttle and hard braking every 2,3 seconds each tank upping the length of time throttle is pressed, then after tank 4 u can go full speed, engine will settle over time I rarely need to tune mine and they start everytime with good engine care :)
That's because you don't know what you are doing! They are considerably easier than traxxas cars, especially when you're following the traxxas method. Every other manufacturer doesn't have the complicated breaking method like traxxas. I have hpi and traxxas nitro cars for over 20 years now.
HRP....We need vehicles to be manufactured so we can buy them. When we can buy them you can make money. Nitro Savages. We especially need nitro Savages. Get a Savage CZcams channel to show off how amazing it is and you promote the channel on snapchat and TikToc. People will come back to you, but you need to start engineering again wonderfully durable great looking vehicles. Especially the Savage line. Nitro and Brushless systems
I have just purchased a BRAND NEW hpi nitro star 15, along with a new glow igniter, new batteries for said igniter and the hpi recommended 20% nitro fuel. I filled the tank, started the engine and proceeded with the factory break-in process. It ran for 1/2 a tank and died! The glow plug from hpi had already burnt out!!! Horrible..
It’s 2023 ……still watching this….👍🏾…..thank you!!!
11 years later this video is very helpful thanks 🙏!!!!
SAAAMMMEEE, was having so many issues tuning my nitro rs4 3 evo+ with the T3.0. The G3.0 is basically the same engine to my knowledge so this was still suuupppeerr helpful!
Same here 🙋🏻♂️
2024! HPI Perfected this a looooong time ago 👏 💯
Thank you so much, got two buggies up an running perfectly following your guide - superstar!
Used this for most of my nitro buggies regardless of hpi they are very valuable information
The best video for toning your hpi engine
Most helpful video about breaking in .nitrogang baby!!!!!
hello. hpi. ilove your cars and im glad for this tutorial because my car is old and needs to be fixed. but where i live i cant go to a shop and tune my car. hopefully my car can survive for muself to enjoy it while it lasts
Great video - This helped me lots!
Great video now my cars run perfect
very nice tutorial im newbie and a have new nitro i watch and learn how to used this nitro car thank very much
I love you guys
awsome vid
iam buying 1 of these now
Almost like the original 1993 Team Associated instruction video, but with actually useful cinematography, instructions, voiceover, audio, and illustration.
Thank for instruction lesson in first time engine rc running
Thanks, really helpful! xD
Nicely done. I have a t 15 and can't get it to stop dying when throttled. Idles great. Starts right up. The base settings described in the manual are not the same as the T 30 you demonstrated. Got me a new T 30 to drop in if I don't get the issue solved. Anyone with an idea please post.
You only have to break in 1 time but I would recommend using about 7 tanks to make sure u bucket is fine because some people don't 7 tamks amd the people that do use 7 tanks to break. In usually find there bullet is quicker
no you only have to breakit in once.. but you do have to tune it depending on the weather..the only time you have to breakin a engine is if you replace any of the internal parts like th pistonhead or the sleeve
will most of these tips work for a nitro tomahawk st
I'm having problems with my nitro traxxas slash trx 3.3, I dont really know how to tune it, it stalls in the beginning, even when warmed up, then it takes off bit shuts off when I apply brakes
Thx, HPI the best
love my rs4 .
Mark Gilson what carburetor do you have on your rs4? i have a .18ci 3.0cc engine, the carb is bad, but don't have any idea pf what to get, thank you
can i use a rear exhaust engine with a slide carburetor? thanks...
Hi. I have a tamiya tgs running the HSP 18 Nitro Engine 2.74cc. Have installed the engine. When the engine starts up the all four wheels starts spinning. Can’t get the idle settings or tunning setting right.
Please tell me what can I do and how.
The new hpi bullet nitro st does not have a low speed needle but if u watch this vid u will get the hang of it . My bullet is ssooooo quick it was a great buy and it is well worth the money but make sure u get nitro ones thay r the best
Can I do this to tune any nitro RC ? I have inferno st 09
Legend says that Hpi still likes comments till this day.
It's not that easy :)
@@OfficialHPI haha
Yes, the general tips will work for you car but as for tuning, always refer to your manual. Since this video is not of your brand of car, do not rely on this video, just use the procedures in this video as tips and always refer to your manual for detailed instructions. As for breaking in, use the directions in your manual as different companies use different techniques.
Would love you to bring back the firestorm
Which RC is this one?
Top...volta pro Brasil
So I have an HPI nitro MT2 from way back before the 2009 models. I need a new needle bearing and a new bottom plate. The MT2 was discontinued ages ago. It feels like I had no hope.
The Chassis for the MT2 is:
www.hpiracing.com/en/part/73946
It is still available. There are very few left however and we will not be restocking when they are gone.
You can find details of all the Distributors currently signed on here:
www.hpiracing.com/distributors
The needle roller bearings are discontinued. But I know brands like Kyosho also used them under the number LD70. I believe you could also use two 5x8x2.5 ballrace bearings instead.
@@OfficialHPI hpi, do u plan on bringing back the savage parts?
200-250 degrees. Never go over 250. If you do, richen the mixture right away.
Soooo, you can keep the break in settings, will that damage the engine
No idiot
Look at my firestorm video, is it good ?
anyone notice that when they are showing needle settings even tho they have engine noise, the flywheel isnt moving
¡Envía sorprendentes
I have an eco rush. At idle it keeps moving forward and I have to keep the brake on, the throttle dial on the controller is low. I then adjusted the high speed needle and when I start it, it accelerates and burns through the fuel quick. Help!
Set the idle screw on the carb so it not reving as high
@@thomasozanne5721 I have the same issue, do you do this when the engine is warm?
do i have to do break in evryday i use...or on just the 1st run of the car?
please answer fast
esteven pascual well I’m 6 years late, but you should always warm your engine up
scavvyboixd TTV lol
Breaking in is easy, you need to read less and play more I usually on all my cars trucks no mattet what instructions say I run 1 tank on idle, then 2 and 3 tanks of gentle throttle and hard braking every 2,3 seconds each tank upping the length of time throttle is pressed, then after tank 4 u can go full speed, engine will settle over time I rarely need to tune mine and they start everytime with good engine care :)
Can someone tell me how to take the motor out?
can't get my new t15 nitro star good :(
You only have to do this once, which is when you first buy it.
is the hpi trophy buggy a small block or a big blog and witch video i must follow?
141Marios big block
I never got the dvd with my bullet mt
i wish it was that easy...lol
How do you set the gear mesh on the 2-speed trans?
Not Too Loose & Not Too Tight To Where You Can Pull A Piece Of Notebook Paper Between The Gears Without Tearing It 👍
I couldn't start my nitro engine, i need help
200 being a cool temp and 230-250 is safe...over 280 is overkill and richen right away
ive had alot of rc car hpi is the hardest to start and break in
That's because you don't know what you are doing! They are considerably easier than traxxas cars, especially when you're following the traxxas method. Every other manufacturer doesn't have the complicated breaking method like traxxas. I have hpi and traxxas nitro cars for over 20 years now.
HRP....We need vehicles to be manufactured so we can buy them. When we can buy them you can make money.
Nitro Savages. We especially need nitro Savages. Get a Savage CZcams channel to show off how amazing it is and you promote the channel on snapchat and TikToc.
People will come back to you, but you need to start engineering again wonderfully durable great looking vehicles.
Especially the Savage line. Nitro and Brushless systems
promotion is a key thing they need right now, and a lot of it
a firestorm even... same price, damn durable....
muitobom]
You guys with HPR now?
HRP Distributing are the HPI Racing Distributor for North America.
Quanto custa ?
what temps shud i get from my engine
Volcano levels
This is really old, why not make a newer version video?
A newer version will be the same..maybe just little more detailed on how he will explain it.
Benny Lara old but gold
Benny Lar
p
That would be good!
there isnt a reason to update unless enough people say the instructions are so outdated they are damaging the car
I’m confused 12:36
Rcc kar ke rate kitne h
RC model car engine wali ke rate comment comment Karke Jarur batana
I have just purchased a BRAND NEW hpi nitro star 15, along with a new glow igniter, new batteries for said igniter and the hpi recommended 20% nitro fuel. I filled the tank, started the engine and proceeded with the factory break-in process. It ran for 1/2 a tank and died! The glow plug from hpi had already burnt out!!! Horrible..
Ronnie Grey maybe it was too lean or rich on LSN or HSN. Most likely to lean
Is Colgate kitne comment Karke Jarur batana
too late now!!!!!!!!!!!!!!!!!!!!!!!
All the pepel that. Run nitro Run a hpi baja
this rc sucks look at mii vid on mii other user it is called overview over $4,000+ HPI savag w/other stuff
i prefer slow acceleration and more smoke , less accidents and nice effect xD