62kWh isolation problem [part 1]
Vložit
- čas přidán 28. 03. 2023
- "P0AA6 EV/HEV Hybrid Batt Volt Sys Isolation" the line no LEAF owner wants to read. Enjoy the progress of me figuring out if this is salvageable or not!
Massive thanks to all my Patreon supporters. Like the content? Consider becoming a supporter: www.patreon.com/dala - Auta a dopravní prostředky
![62kWh isolation problem [FINALE]](http://i.ytimg.com/vi/BkKc8l0CfeQ/mqdefault.jpg)
![62kWh isolation problem [FINALE]](/img/tr.png)
Hi Dala. Just a thought. I used to work at a Nissan Dealership and we had isolation problems on 62kwh packs more than once. I was always that exact same module you are working on. Never a physical dent or damage but rather internal chemical defect that caused the leak. Under warranty we would always end up replacing the module altogether and we never had any comebacks.
Is there a way to get new cell from Nissan?
@@andreybalanchuk8387 when I was working there unfortunately no. You can't just go to the parts counter and buy a cell/module even if you have the part number and money. Battery components are only sent to dealerships when there's an actual diagnostic case going on and they have a tech line case number. But this information applies to Canada and was valid in 2022. Don't know if it still holds.
@@cloutiernicholas don't think it's any different here in US. So only way for such repair is looking is someone sells individual cells from 62 battery which I didn't see yet, they are relatively new and reused as is.
So Bad battery Not to buy used 62kWh
Seeing as you were measuring a voltage to ground from the - and the + terminal, would it be possible to work out which cell in the pack was causing the leak and taking it out to have a closer look?
Well, first you need Megger (Fluke 1507 for example) and use it at 500V area. Then inspect that is there connection to battery chassis/frame. Because there has been collision, there can be bend module frames or battery pouch leaking electrolyte. Also find out those bad cells and replace them after knowing reason for isolation problem. Do not make same mistakes what I have done with my Focus Electric. 😁
- Measure first with Megger, normal multimeter is quite useless with inside battery repairs.
- Take videos to yourself to remember measured values and you see your working methods, are they have been right in the past (like if you do wrong diagnose, you can double check).
And be happy that you do not have coolant cooled battery as I have, also you have more space and warm place to work, I did not. This is quite simple diagnostics after all. When you start figure out Megger and circuits in battery, you will find problem quite quick. Next time is so much faster and comfortable to do when you have some routine.
Lycka till, lykkyä tykö! 🙃
A further thought. The pouch cells within a module might have shifted and one or more of the cell tabs come into contact with the cell case. Removing the restraint bars may then have alowed the bent cell tabs to push the pouch back into place.
A very plausible possibility.
Good idea Paul - I think you might be right!
Ooooh, yeah, I could buy that. The tabs on the pouches are all forward. How about turn the module with tabs upward, without the compression bolts in it, and tap it on the ground, maybe on a thick rubber sheet. Try to make the cells sit back down toward the bottom. Like straightening a pile of homework papers that has just been collected. And since all the modules have been subjected to the crash deceleration, do the same to any other modules which have their tabs facing forward. Is there part of the metal case on that side of the module? I don't see anything but plastic on that front side.
that's exactly wot i was gonna say, so "wot E said" is my comment ;-)
Good point! There may be some insufficient clearances inside the pack. Seems unlikely since it's a high voltage battery... but it was designed by humans, and we all fail. If it ends up being this, it seems like a wise idea to spend/invest a few extra hours doing the same thing to every module.... since the entire pack suffered some kind of indirect impact force.
I was late for work because of this video. Totally worth it.
When you have torqued the cell, you did not have the angle iron bar as part of the configuration. I noted there was one when the cell was in the pack. Maybe this difference in load in the pack is enough to not induce the fault. Try re-torquing with all the hardware as it would have been in the battery pack, and see how that goes. I'd not be trusting the pack as it is tho.
So impressive to see people that understand electronics.
The dent does not look high enough to touch the battery. Loosening the connection terminals may have changed the contact resistance. Try loosening the plate bolts, take a volt meter measurement then re-tighten. Try this method with a meter continuously taking readings. Maybe just a bad contact.
that does account for leakage path
Hi! Electrician here : Your high voltage gloves MUST BE WORN WITH LEATHER PROTECTORS over the insulating layer. They are NOT designed to be used without leathers!
Hi, Dala ! Given the Voltages in the video (-22,43V and 12,58V), it is easy to say, that the problem comes form some of 3rd cell row in the pac (form top, or from the bottom - I don't exactly know, should check that on the module itself, having in mind that pac comes with 9s2p). Lucky for know that it is probably only one cell to ground for now. If there would be a second one too espiacialy in some longer away pac there would be high currents floating between with fire in the battery.
The idea that battery was in car crash and because of that some screws moved is not necessarily the truth. Cells in those pacs are very well known for being often expanding with aging and especialy QC to full in hot environment. If that is the case, if all cells are expanding the pressure could even move or even bend the screws. But of course - that is the sign of seriously used battery. Would be easier to check live with a naked eye if that could be the cause because it is hard to say from the video
Hi Dala, we are doing repacks with modules from China and one of the modules was placed on an uncleaned surface. It has a small dent of 2x3mm and is less than 1mm deep. This module is shorting to ground due to the one cell being damaged.
The modules are made up of prismatic cells stacked upright and bound together. Technically speaking, when the cells are manufactured, the insulator that is rolled up with the active material should overlap a little, so that when the flattened roll is squeezed into the box, the active material should be nowhere near the metal can housing.
Clearly these tolerances are way lower than we would have though, or we were just very unlucky.
In your case the dent that was made in the base of the pack, clearly pushed fairly hard through the steel 'frame' of the module and made a dent internally. You would have to bolt it back onto the bump to replicate the fault again.
My advice would be to replace that module/cell if at all possible. The chances that this cell will fail prematurely are very high, as dendrites would have a much shorter path.
The soup packet cells seems are more forgiving, so if you wanted to take a chance, it should be ok to remove the dent and refit the pack.
Thanks for putting your stuff out for others to learn from.
Great channel!❤
Regards Jens
Modules from China??? My 2011 leaf only gets 25 miles per charge and is supper clean and has no other problems. Love the car but is becoming useless
Energy density is the name of the game
Where are those modules available to purchase?
@@EuphoricHacker Shenzen Starmax
Is your project to strip down prismatic cells to replace the original pouch in Nissan's cells? Or is Shenzen Starmax doing cells that matches Nissan? If you are stripping down, which prismatic cell model are you using?
Thanks to let us look inside!
I would loosen and retighten every pack, re-position all the straps , re-tighten those, inspect and reconnect all the bus bars, then test it again. I would make a cable to connect the battery to the car without installing it in the body, and test operation with the car up on blocks, use leafy spy, and test all systems...see what you have.
Been running great for many months now 🤩
Thanks for the video. Very interesting stuff. I'm sure you will figure it all out.
Seems like pretty good news. I'd be pushing hard on the bottom of that module where the dent was to see if I can get the earth fault to come back. If you can't, then put it all back together (checking for the fault along the way) and hope you have a reliable battery pack.
I'm also a little concerned about what caused the other cells to discharge like that. I'd consider pulling them out and inspecting them closely.
Maybe that module is suspect in the same way. Whatever you find in the one rear module (shifted cells, pinched balance leads?), look for same in the out of balance module.
I'm never going to take my battery out however this is enormously interesting Dal. Thank you for sharing.
Greetings from Sweden.
Since i am just in my first month of owning a 2019 40kW Leaf @ just 38000km. I am watching your videos to have the knowledge when there will be a problem. I thank you for your great work. I am looking forward to the upgraded charging projekt.
Extracted module is in 9s configuration. Looks like one of the series cells is leaking to its outer casing. Compressing doesn’t work, probably because it was touching the battery case when it was inside. I guess you’ll have to carefully examine the module for visible damage, and also take some voltage measurements around. Problematic cell should be #3 from the top or bottom.
what I like in your video is that you are very safe when working on the high voltage system you have proper PPE and isolated tools etc to work on this I see a lot of videos on U tube and they don't take it seriously and hope that you find the problem and you fix your car cheap.
Great video and thanks for sharing. Can"t add much more than what has been suggested below. You do need to find the reason for the lower voltage cells though. Check connections that may have been loosened in the accident. Good luck !
Hi Dala,
I would add to dissasembly all other stacks to correct bendings from the crash. Also, after complete the pack reassembly, performing the insulation test with Megger in the extreme temperatures you could have in the future. Best regards
Flattening the dent from below might be the solution to removing any additional compression that caused the ground. Or lay a thin sheet of insulation between the case and the bottom of the stack, and re-assemble to test. Possibly a thin sheet on top if it's closer to lid, but when re-gluing it you could also put a thin shim along that side of the lid before bolting it down to gain a few millimeters of clearance if needed.
Since the same area seems to have a problem in other cars I would swap the cell pack to the right or left if possible and hope I get lucky for a while. Great work! it's likely too late but I thought I'd add my 2 cents.
I would have to say that something likely shifted when you took the compression bolts out, and personally I would not trust this stack to be reliable long term unless you can tell for sure what shifted and that it can be repositioned where it belongs. For my own curiosity I would next use a megger to check the stack to chassis, if something is really close to touching you will find it with that. In the railway industry we use Hi Pot testers to find defects like this in the high voltage traction circuit but that may be overkill for this😂Can't wait to hear the follow up and thanks as always for an informative video :)
Is there a torque level that you have to reach when re-compressing the module? - What I am thinking is that you might not have compressed back the module at the same torque level as it was while inside the battery. - So maybe if you compress to the adequate level, you'll see the problem coming back. - If you do that test, then you can have bit less of a chance to get the problem re-occurring when you put it back all together. - You are one courageous man!
To my mind that dent was superficial/cosmetic and very unlikely to be connected with your stack short. Much more likely is the possibility of an internal short to the case which has disappeared when the stack was allowed to expand free of bolt pressure. You need to look at the internals of this stack for the possibility of a short around the centre part of the cell stack. Very informative and educational videos - I commend you for them.
Hello Dalla, good work you found the module but it must be one of the pouches inside of the module so you must disassemble that module and inspect each pouches it seems that mr coutiernicho knows so just replace it and use that battery again in your car
Good video and information! I'm waiting for a final conclusion. My 40 kwh battery haves the same error, since June 2022. I still drive the car, a 2019 Leaf, erasing the error each time I start it. I made 8000 km since broken down. The condition of the battery has not worsened during all this time, but the SOH has decreased a little, with 2%, which is quite normal, in 9 months.
The strange thing is, it's a single station in my whole town, that let me charge it to 100% with no error, other ones stop charging at 30-35% SOC, when the error comes on the dashboard. Under 30% SOC, there's no error on dashboard, never. It works completely normal, heather and AC as well.
great content
The fact you were seeing 12/24v suggests that there is a short or leak one-third of the way through the series stack. It would probably be useful to measure the resistance of the short by seeing how the leakage voltage changes if you load the meter - that should show if it's a dead short or resistive - e.g. moisture etc. I suppose x-raying the pack might show up internal damage, but probably needs a powerful industrial x-ray to penetrate the steel sufficiently.
At what point did you disconnect the BMS harness from that module? Was it just before removing the compression bolts? It's possible the isolation problem has to do with the BMS or BMS wiring.
If you look closely, the three balance harness plugs were unplugged from the BMS when he proved the isolation fault just before removing the module.
And it could be the balance / bms wiring within the module shorted to the module case.
If it has been involved in an accident at some point that compression point is the number one suspect on it all. It could be as simple as a small segement touched down internally and when you released and moved it the fault point moved enough to not come back under compression. Given the amount of work to remove and refit I'd just throw a replacement stack at it and realign all the bolts and the like back again.
Still worth what you paid , hope you get it sorted out .🇬🇧
The voltmeter measures against a high resistance load, (the internal voltmeter resistance is very high). It would yeild more information if you can adjust the load that you are measuring the voltage drop across. So put a variable resistance of some sort in the path and measure the voltage drop across that. Provided your resistor is rated high enough wattage. I'm thinking internal damage to the cells (internal resistance of the battery coming in to play) will have a different characteristic to an insulation problem.
Top Man!
Nothing better to say than Nicolas Cloutier. Anyway, disassemble the pack and check each cell. As said Nico, internal leak seems the more possible reason or maybe a cell damaged. The leak shoud be reproductible. Can't say better because not in front of the pack.
Congratulation, you are back on track to solve this problem.
Slacken everything off re align everything tighten everything back up and see how it goes
Seems like a tricky situation. A weak module that you charge to balance, if weak will eventually imbalance itself again. I remember some other Leaf owners mentioned something about testing the modules under heavy load. Essentially "weak" cells would drastically drop in voltage when flooring the accelerator. A bit tricky to "replicate" that load but it's something to test and verify if your weak cell will end up losing balance again. And the worst is a weak cell shorting and frying the rest of the pack like mine did. As for the shorting pack... I'd personally replace it.
I guess tldr, replace both modules. These should be specially manufactured so I don't think they disassemble as easily as the 40kwh modules. You could try out of curiosity and see if you can repair it but my gut tells me the high density leaves it more vulnerable to physical damage and as you said, these are damaged.
If you have an isolation issue once, you'll get it again. Also to properly replicate the isolation, you would actually need a bottom plate to mount it to right? I don't think the bolts are enough as the shell flexes. Either ways, you don't want to be surprised by an issue you didn't fix with certainty while on the road in a 3500lb moving vehicle.
Since there was this dent in the bottom right under this cell, there might have been some pressure from the underside of the cell.
To emulate this pressure a C-clamp might be used. Have a thick steel plate at the top of the cell in order to spread the pressure at the top of the cell. Then place the C-clamp approximately at the place of the dent and squeeze.
Another possibility is the misplacement of the cell. Maybe they did not loosen the attaching bolts for good lookibg cells and only replaced the bad ones or none after the crash. When You loosened the cells, the cell frame straightened and now there is no more leak.
Yes I will clamp it harder and take more measurements with a dedicated insulation tester!
Great diagnosis and I think because that looks like it jolted the pack and the dent was under that module and that's the one you had the leak on, I wonder if it internally damaged one of the cells and it is one of those that's given the reading and you uncompressing it and then recompressing it helped it for now. I would fear that once the cells have heated up and cooled down under charging or driving you may well see same fault again. I know you said they hard to get hold of but for piece of mind I would keep a eye out for a replacement module, but getting one to match age and state of health will be a pain. I guess you could also strip down the individual cells and see if any obvious signs but maybe shock of crash internally damaged a cell. I also guess if you don't mind having to re seal it and then maybe having to drop it again you could refit and test.
You can clearly see on a video what a lockage was been somewhere in a middle of this module.
Since the cells are super low resistance, i would think it would be safe to use a Mega-ohmmeter (Megger) to see if it can locate the weak spot. It works wonders for mains wiring.
Yes, I will try this, I got a meter last week!
Yes I guess it’s like our micro ohm meter we use to test all connections in a string of batteries. It’s easy to see which connection needs help.
@@zxggwrt nope, it's the exact opposite. It's not meant to find that low of a resistance. I think the lowest reading you can see accurately is around 1 ohm. But the trick is, it uses 250, 500 or 1000V for measuring instead of a couple of volts. This makes bad insulation show up.
Hi Dala. Thank you for sharing. Have you checked the isolated busbars of this module for breaks on the insulation? I know this is a simple thought, but you never know.
I think the first thing will be reproduce the leak.. put it where it was, (no dent repaired) screw it down and check if you have a torque wrench, check how much do you need to tight the battery to start measuring something...
if you manage to reproduce it, then you can extract it, and put the battery on top of a metal plate with a nut/ screw (small one) underneath... that way you are replicating the conditions outside the battery pack...
if you see the problem, then the problem is 100% identified... then you can dig a bit more... disasambling the battery and checking for damage on each cell, or you can think in solving the problem... you can replace the module or just simple flat the spot, then put some soft foam isolation (just a bit more, just in case).. then close the pack and enjoy as it is... (of course if you can replace it together with the front cell that is damaged would be perfect... but if you dont find a replacement, then just enjoy what you have
Can you dismantle that block and lay it our into individual cells and then examine them carefully. If any electrolyte has leaked from any block or bank of cells id scrap them off. If the individual cells look ok when dismantled and they are not electrically leaking, then id put them back together, bolt the case up, and install it back in the car and run it for a few hundred / a thousand km and re assess. AT the end of thet day you have nothing to loose at this point. Great video, and good luck with it.
Great video, I can’t wait to see the root cause. The person that worked at a dealership seems to have the best advise. Determine their cell and replace it. Or is the BMS damaged?
Need put back to main battery place and measure again. And I would use vacuum to clean some extra dust. Industrial dust always present. Thanks.
Since you are getting negative leakage voltages then that implies a positive from a cell somewhere in the middle of that pack is not right. Can you pull the pouch cells out one at a time and inspect the ones around the middle?
Could it be related to a torsion issue? By that I mean, when you bolt the battery back into the base it could be twisting the cell casing slightly. It twists just enough that driving vibrations start to shift the internal pouch cells by micrometers, causing it to either wear away or permeate the isolation material and contact the outer casing?
It’s just a thought.
I would reinstall the battery cells and hook everything up to the car to see if anything has changed. I can't tell you how many issues Ive resolved over the years doing nothing but investigating the problem. It could have been an unsecured or loose connection that you fixed by removing and reinstalling.
Too bad there aren't battery extension cords for your car :)
Measure isolation with high voltage tester. The cells will have an isolation spec. It might be VERY HIGH, I would not be surprised if it were >3,000 volts ac or > 4,500V dc.
If that seems high, bear in mind something like a metal cased Sky+ set-top PVR box is tested to 3,000V ac for 1 minute
The Rods are steel, if some cell is little bit unpricise, it can give voltage to the rod. Once One Ukranian disasembled the pack with the same problem. He just covered up the Rods with isolation tube and the problem was gone. It was 40kW pack. This problem was not in 24kW packs.
I think simply unbolting and releasing the tension (and shifting the electrolyte) is what atleast temporarily fixes the modules! It is good that the bolts are steel, having the system unable to detect leaks would be quite dangerous.
The voltages you measured between ground and battery terminals before you removed the faulty module were 12.x and 24.x. This suggests the short happens on cell number 3. I suspect that cell is somehow shorted to the one of the compression bolts.
I would 100% agree with you!
ballance all cells, check for continuity, before closing the battery, i think the whole battery pack is ok, the drop in the voltage on 4 cells must be because of the leakage, double and triple check for leakage before closing the battery.
Unbalanced moules and modules with isolation fault is 2 different modules.
Grub megaommeter and see what is said. This is how I pinpointed some insulation fault on defective 40 kWh pack. But my case was been much more obvious.
I would take apart that module and examine the pouch cells carefully, and measure voltages before reassembling the whole pack. I don't think that dent had anything to do with this. The hard collision has compromised the internal structure of one of the cells.
Good luck!
The module casing is unfortunately welded together, so it is considered a non-serviceable component. But I will take some more measurements in the next video!
I think a cell tab in the module has been in contact with the housing.
I would open this module, to see that all cell tabs are located correctly.
maybe it's only 0.1mm between tab and housing now.
Then a temperature change can cause it to come into contact with the housing again, and the same problem occurs.
Then I would loosen everything in the battery pack, so you can put everything back correctly.
After that, I'm sure you can use the battery without any worries.
The cells in the battery can actually withstand major mechanical damage and still function perfectly well.
If you stick a screwdriver through a cell, it doesn't catch fire, it just grinds and smokes a bit, but the cell still works.
Having said that, you should never use a cell that leaks.
But the cells in the Leaf are among the safest used in any electric car.
How often have you heard about a battery fire in a Nissan Leaf?
Good idea, will do this in the next video!
nice videos my friend, you really add value to the community. quick question, is it possible to remove the top speed limiter on newer leafs? the 62kwh version is capped at 165kmh can that be removed? also, would it be bad for the battery/motor? would be interesting to know!
No, the 165km/h corresponds to >10kRPM , so going higher would over-rev the motor.
Hi Dala, one of the pouch cells of the individual battery packs may have become defective due to the mechanical stress of an accident, this may only have an effect when the entire pack is pressed. Perhaps use an insulation tester (approx. 1000 volts) to carry out an insulation test on several cells in the block in question.
Maybe you need to take a very close look at white “insulation” in pack - are there any small holes? Can you add another layer near shifted cell stack? Any loose pieces of metal in tray?
I saw such damage - the cell was touching the screw. There should be marks on the cell and the screw. Just put insulation on the compression screw.
I don't think crash damage is the cause, rather a coincidence. Disassemble, assemble, torque properly. If no physical leak, replacement is not mandatory.
Thanks, I'll do some more measurements first, stay tuned for next video!
I think of a problem of insulation in the holes where the bolts pass to put lock the battery. I would try to isolate these bolts
Nice work. from my point of view you should probabky take out a modules, inspect them for damage and reassemble. Replace bent parts and maybe use new fasteners. If the problem does not reappear you should probably be good for now. if the cells had been damaged, they would most likely have caught on fire by now, but the shifted positioning and so might lead to issues with chafing insulation, so better review and reposition. If you can stresstest the module outside the car and fully charge and discarge a time or two before putting it back intt the car. Hopefully then you have a working and reliable pack again. If you want to play it more safe, then you would need to dissassemble the modules and check every cell.
Does the fact it was 12v to ground from one terminal, and 24v from the other give you a pointer to where in the cell pack the ground fault is/was?
Yes, you right, damage/fault is somewhere in a a top/bottom 1/3 of the pack. I would inspect balance lead connections, maybe where is a small tolerance to a module ground and colission shifted something too close/something get bent a bit or scratched.
@DalasEVRepair I have this problem on my Nissan Note e-power HE12. I am very sad that the megohmmeter and other measuring devices cannot detect this problem... leaks and startup prohibition - while the problem is “floating”, you can drive 300 km, or 50 km... and then get an error...
I guess most of us will be keen to know if there are any simple tests to check a battery pack before buying. For example, would a resistance/isolation check between HV connector pins and the case show us a leaky pack or do we need the pack to be installed in a car with contactors "on".
Was there anything else beyond the compression bolts that's missing to try recreate the issue here
I think the crash was too violent and it may have affected some of the cells in that module(marked X).
I would also do a thorough check on the module that has lower voltage because is very rare for these batteries to just go off balance.
All the best.
Thanks, will do!
If pack did not have isolation problem, would BMS charge up that module that was 30 mV lower than others?
Hi. You should test condition of the next module(to the left from this one). The point of insulation will be with no voltage to body, but with low resistance.
Thanks, will measure more in next video!
When working on hevy cells like that please keep them on a trolley so if things go bad you can quickly get the pack outside.
Good tip!
May be the dent was putting pressure on the module unbolting it relieved the pressure
Hi i would leave module tighten like this and charge it up to the max level than discharge if thermal expansion will return the isolation fault if not i would put it back
I think that the compression was at the place of the deformation of the sheet. But when you tighten the 4 nuts, the compression load is not at the point of impact on the sheet.
As @Bernard Peraldi above, with the pack removed you're not actually tightening the battery case down to what might be the distorted surface of the battery tray.
You can either bolt the pack back in and repeat the insulation test there or bolt the battery pack down to a flat (two layers of 18mm plywood) surface on a workbench and deliberately introduce a distortion onto the surrogate battery tray surface with a spacer of some sort to effectively distort the battery case deliberately while checking for a voltage leak.
Did you get a warranty on the battery pack
If I was you , I should taking apart the hole damage cell part and inspect any damages!! do not put this pack back with the rest of them!! try to buy an other. you may damage the hole pack in the future or take a fire after some chademo dc charging. Also try to find the isolation issues with a megohm-meter, so buy one!! when we make inspection or an isolation issue , there is only one type of meter that send 250V 500V and 1000V dc to the line in order to find the isolation issue, megohm-meter . You will never find isolation issues with a simple Ohm meter only... the pack was squeezed but also was under a big voltage ! the issue is there and for the most part must be from the half of the pack and down!!
Replace that module, for peace of mind. Also check all of the base of the pack for more dents.
put it back.. and draw a 1amp load from that module and the frame .. and use a thermal camera to show where the heat is.
Interesting idea!
Further disassemble the stack where the fault was, if that dent has in any way pushed onto the pouches inside you might be able to see this on the bottom one, and that would be smart to investigate.
You need angle grinder or a drill at this point. By Nissan manual, module is non serviceable component and needs to be replaced as a whole assembly.
@@pashko90 Did not know, that's a bummer.
I would put some insulation strip of material under all those modules and out it back together. Should work for coming years
The LoZ mode on your meter should work faster for the measurement because it introduces a bit of load to the circuit and discharges the capacitor quickly?
Good idea!
I'd knock out that dent, realign everything correctly put it back together and do a further insulation test. There doesnt appear to be anything physically or electrically wrong with the cell module itself. I'd defintely capacity test that low cell to see if it matches the others while you have the battery apart - it may need replacing.
Good idea, more measuring incoming!
The Dent itself looks like it was made with a forklift for instance... The presumed shift/slide of the pouches in the pack could be explained by this, the pack sliding of the forklift and dropping on concrete? That's a hell of alot of G's with no deceleration distance whatsoever!
Yep, the battery had some classic forklift lovetaps! Will need to tweak lots of points on the inside!
Battery box is bent. When you tight screws in to pack + battery box something will touch wrong place inside pack, or just it bent and cell insulation fails.
just put everything together and the modules directly. what else can you try?😅
Your channel is amazing , i had alot of knowledge about ev batteies, can you explain what is the isolation problem ?
See this video for more info on what an isolation problem is: czcams.com/video/00eEj_EgMas/video.html
if it was up to me i would take apart all battery modules cell by cell and inspect for any tears in the pouch cells, safety is at most important when dealing with these ev battery packs especially if it came from a crashed vehicle.
Put 1cm small thing under the pack. Put pack on it. Just step with your 80 kg on it and measure.
Or ask someone to step on it. It's not a bad option.
The cell was being crushed in the centre from below. Hammering out the dent will remove the crushing force so it will probably be OK but has the cell been irreparably damaged? Clearly it was not a serious safety issue as it was only 12V to ground so safety is not a concern here.
Only you know if it is worth trying it again with this cell as it is your time you will be wasting should it fail again.
How much are replacement cells (if available)
How much is your time worth?
check the module on the left because the busbar was still in contact when mesuring the leak
That busbar goes to the service disconnect swith (which is empty)
maybe compressing the cells in the complete battery puts more force, if possible try to disassemble the cells maybe one is leaking electrolyte and that will conduct electricity to ground. The only people i saw opening the cells are the samurai guy of the pikes peak leaf when they added cooling to the cells and had to place cooling sheets between them.
Please check if there are no connection between compression bolts and the modules in pack. Looks like I saw a video with damaged pack, where some of thin leafs from the modules touches that bolts.
Please look at this video czcams.com/video/zqK30tvq3m0/video.html
Yes, "carreapirvideo" did it on CZcams. I remember leakage thru a stud holes.
Sorry to hear about the bad news Dala, one question though, did you get the pack from Norway, and how does the seller react to the situation? Will they refund you, at least partially? And would you then get back the import tax in Finland (for the difference?)
This was from a private seller in Sweden, so no company warranty! I don't blame anyone for not knowing that the battery pack was too damaged, this is very hard to spot!
@@DalasEVRepair very understandable. Good luck on getting it repaired.
The comment from Nicholas Cloutier suggests that the sub unit is faulty and Nissan would have replaced it if this had manifested before the accident. Lacking availability of a replacement, I would personally sell off all the other sub modules to recover costs. Over time we may see if Nicholas' comments are supported elsewhere and what this means for the usability of the 62kwh pack outside of a Nissan warrantied car.
Yes, looks like Nissan always goes with a replacement. The modules cost ~7000€ via Nissan. We will need to find a used one!
Are these out of warranty already!?
From the voltages it looks like short circuit connection to ground somewhere in the 2/3 or 1/3 fo serial string of cell. You cen exactly count which of serially connected cells in module was leaking from the voltage of cells and the leakage voltage. I expect it will be somewhere in the middle. Dent on the bottom could have nothing to do with the issue. Locate the cell and you will see what is bad. Are the side walls or the area where are cells connected each to other ok? May be the module was shifted from the forces from accident and something touched the metal cover from inside. I am just guessing that in front there are 7S, middle is 4s and rear are 9s configuration so it should be short circuit between connection 3rd and 4rd cell to the ground. Good luck!
I would put it back together with more insulating paper on the bottom where the dent was. See if you can keep it going.
Already fixed in the next videos!
Hi Dala!
I don't understand how manually balancing the one stack would fix anything. Because I'd think that the car should do this on its own - does it not? And if voltage levels get adjusted, would it not just simply go out of whack later on because of some internal defect of the cells? What caused the imbalance in the first place? Some temporary leakage during the accident or something more permanent?
As for the leak: No idea. How expensive is a replacement stack? What is the worst that could happen? unexpected shutdown? fire?
The balancing is very weak on the Nissan BMS, it can only shunt 2.5mA , so letting it balance on its own would take months, even years! Better to do it while the battery is open.
Replacement stack from Nissan is 7000€. Will need to source a used replacement. Worst thing that could happen is more unexpected shutdowns. The system is very sensitive, it triggers on a 380kOhm leak to GND.
@@DalasEVRepair Hm. Try to reproduce the fault by shoving and banging on the stack until it bodges - or not. If you're able to use the car as a Beta Product (failures possible) for a while, then I'd keep the old stack. The longer the battery works without fault, the less likely it is to happen again. It should then be promoted from Beta to fully usable after a few months.
Cracking the battery open again is possible, while not really desirable, eh? But that would be the money poor, time rich way. Not sure if that suits your life.
Do you think the unbalanced stack will go out of whack again? Can you measure internal resistance? Maybe connect a toaster and see how much the voltage drops, compared to other stacks...
Look carefully at the particular cell tabs, indicated by the ~12v and 24v seen between the terminals and the case, that's particular cell tab that was touching the case. How about checking the balance lead wires, maybe one has been pinched.
The issue was still there without any balancing wires connected, but I will inspect the front of the module more in next video!
Dala, can you help finding the spec on a 40Kwh battery? I have the same issue internal battery pack insulation leak. I am not able to find a vedio or spec on it. Thank you
You can use the measurements from the 2015 24kWh pack, the details are close enough with cell layout and values: www.nicoclub.com/service-manual?fsm=Leaf%2F2015%2Fevb.pdf
If it's an electrolyte leak, (sad, sorry), maybe it's capillary action which sucked the electrolyte back into the cracks between pouches and plastic between cells, when it was uncompressed, and cleared the short. If it's a leak, see if there is room at the edges or corners of the cells, maybe from the tab end, to gently push a q-tip small cotton swab, or sliver of stiff paper inside, and does it come out wet or green with electrolyte.
Yes, most likely I will need a replacement module. The electrolyte is transparent, so very hard to spot these!
If so, since the 62 packs and modules are scarce, I wonder if a Scandinavian EV genius could reload that module with cells from a 40 module. I'm very sorry about the trouble you've run into this time, but I'm on the edge of my seat to see exactly what is the root cause and how you fix it.
I'm probably way too late for this, but I'm curious if just the dented casing was touching the bottom of that cell stack which caused the isolation issue? You could confirm by just electrically connecting the bottom of that cell stack to the outer battery casing to see if that would cause the isolation problem?
No the dent was actually not high enough. Red herring!
After reading some of the other replies, I guess as much. =/
It would also by a pretty awful design if that were the case. =D