Restoration AM6 Engine - Complete Process
Vložit
- čas přidán 4. 05. 2023
- #restoration #yamaha #engine
In this video you can watch restoration of YAMAHA dt50 Engine. This will be first part of this series. Next part will be uploaded soon. I hope you enjoy today's video. Let me know in the comments section what to restore next?
More Restorations:
GoKart Restoration - • Restoration Abandoned ...
HONDA CG125 Restoration - • Restoration Abandoned ...
BMX Restoration - • Restoration BMX Bike -...
PocketBike Restoration - • Restoration Pocket Bik...
YAMAHA Restoration - • Restoration Abandoned ...
#restoration #motorcycle #yamaha - Jak na to + styl
Video shows that the engine was only washed not restored
God thanks 🙏🙏 !!! Finally a more serious comment than the video
Because it's such a good engine that it doesn't need to be repaired.
And sand blasted
@@tajfun9021 you cant tear apart and engine and not do the seals or barrens let alone head gaskets looked like they were cardboard
He is restoring it to better condition… no where in the title does it say rebuild or repair😂
Is it called restoration without replacing wear and tear parts such as bearing and oil seal?
No it's called cleaning
and he put the clutch pressure plate on the wrong way
@@venni3996 nah its the right way
@@sweguy3602 He did put it first the wrong way, but then fixed it and cut the part where he fixed it, out of the video.
Restoration: Fix EVERYTHING that came off of the object.
Rebuild: Fix everything by either fixing it or buying new parts.
This is not what I consider a restoration. This was a clean and paint job. No rebore & piston. You even reused the head haskets. It's prettier than before, but mechanically its unchanged.
I would hire you in my shop as a blaster and painter before I hired you as a mechanic.
czcams.com/users/shortsZLtGHOCltHE?feature=share
facts bro,he couldve done full maintence on it but didnt even change the cylinderhead gasket🤣
Mechanically unchanged is an understatement.
Has only gotten worse. He even made a gasket for the 2 case half's, increasing play in the shafts even more.
My man used the wrong screwdriver for the cluch, and the head didn't even meet the cylinder. So, squish clearance would have been way too big.
Technically worsened for sure.
I could literally go on an on.
Mechanically unchanged is an understatement.
Has only gotten worse. He even made a gasket for the 2 case half's, increasing play in the shafts even more.
My man used the wrong screwdriver for the cluch, and the head didn't even meet the cylinder. So, squish clearance would have been way too big.
Technically worsened for sure.
I could literally go on an on.
Too bad for all the work, but reinstalling old bearings and seals is not possible. That has nothing to do with restoration.
not to mention he didn’t oil anything when putting it back in the bike
The sand blasting, polishing and painting were nice, I would recommend doing that with your engine if you're tearing it apart fully anyway. The rest of the build however, I do not agree with and to everybody seeing this and never having done a rebuild like this before but considering doing one, I would not recommend at all doing what you see here. Reusing old seals and bearings after dousing them in brake cleaner and whatever leftovers remained in the crankcase is not at all sensible. I can only assume this build was done for someone who wanted to spend as little as possible or very little in general. When 'restoring' an engine like this certain aspects are of course a matter of personal taste, but replacing oil seals and bearings all around is no superfluous luxury. That piston was looking pretty rough too, and the cylinder wall will most likely have shown a similar wear pattern. I this particular case I would have done something about those as well. We didn't even see if you did maintenance on the carb or clutch. As I was watching I was wondering 'Why would he spray steel components with brake clean and not re-oil them immediately afterwards? That risks corrosion forming on them...' And would you look at that, all of the steel components got rust splotches on them at the point of assembly. Into the bargain, the crappy intake clamps and hose weren't even replaced. That stuff's like a few dollars or euros at your local hardware store, if you didn't have better ones already laying around.
Nice end result to look at, but pretty poor technical refurbishment.
Pic na sprzedaż
Yamaha DT50 is generally the name of the motorcycle that carries this engine whose reference is: AM6
AM6 Minarelli.
@@philippejoseph8604 Yes précisément 🇫🇷
Spot on, I own one
wich is a piece of shit of an engine
yes but from the clutch cover i can tel that this is from an early aprilia back when they had am6
Wow engine looks brand new inside! Amazing how well they’re sealed
No doubt why almost every brand with the same type of bikes uses the same engine
Its minarelli AM6
nice job! also i'd recommend when you tighten down the case bolts you distribute equal pressure, ive accidentally snapped a crankcase bc I didnt tighten the bolts down in a certain pattern.
If you think this is a nice job, you don’t undertand a lot of mechanics and restoration
@@iltutt0f4r35understand*
Maybe you should understand how to spell before commenting.
I was simply trying to be nice
@@TheGameBest7 maybe a digiting error?
@@iltutt0f4r35 possibly
j'ai eu le temps de faire 4 Arrete cardiaque en 20 min de video, tres belle experience je vous en remercie
engine is in awesome condition from inside
Nice vid, some remarks:
Just hoping you’ve replaced bearings and seals off camera🙈
But why are the gears and ALL other internals covered in flashrust?! Would certainly not feel comfortable putting it back together like that.
And why do you bother restoring wear items like the cilinder kit and airfilter?
Would certainly never re-use that cheesy old airfilter🫣
And lastly, you should always tighten the crankcase bolts manually, and more important: evenly!! Goes a long way in not destroying the bearings.
Not to mention how easily the crank slipped In definitely needs looking at
10 seconds in, I had to restart the video because I heard laughter and thought it was outside my window. Nonetheless, excellent work, as always!
This is not a good job. He just wash the engine.
LOOKIN' GOOD, NICE WORK...
I usually let my parts soak in the parts washer while I order new parts to (restore)!
Thank you for the excellent video and bringing back pleasant memories. These were remarkably reliable modern tech liquid cooled 2 stroke with automatic oil injection . You could runt hem all day at 80km/hr and not have a worry. Thank you Yamaha.
its not a yamaha made engine but ist from motori minarelli from italia its an am6 engine
@@henkkaasjes9837 Thank you . I am Italian and spent much happy time on a Yamaha. Till this video that is one of the excellent features I never noticed.
Его можно было не разбирать с такой ‘’реставрацией’’ просто помыть и помыть покрасить
Хорошая работа 😂😂😂
красивый но не более кв без перебора поршень старый цилиндр тоже просто отмыт это что переборка? а звезда это же сюрекен он уже должен быть в утиль как и патрубок впускной который сгнил а его просто покрасили там пора новый делать.
beautiful but no more than kv without busting the piston, the old cylinder is also just washed, is that a bulkhead? and the star is the same shureken, it should already be in the scrap as well as the inlet pipe that rotted and it was just painted there it's time to make a new one.
Nice video. I wonder why the port on the carb next to the ports for pre heat water was plugged off with a screw? Is that supposed to be plugged as well?
surface rust looks good on the gearbox
From a piece of crap to holy crap!!!
❤️❤️❤️👍🏻👍🏻👍🏻
Awesome job!!! Can’t wait to see Part 2!!!
Ficou como novo ! 👍🇧🇷
can you add the name of the parts please in your next videos, i like the method, thanks
What product did you use for clean the paint?
I would highly recommend using muriatic acid to remove rust and corrosion
Muriatic acid eats away at aluminium, which this engine is made of.
Ahhhyy, that really hurt in the mechanic part of my brain... 🤯
Ça remonte des pièces usé en fait ??
Ou est la restauration la dedans à part nettoyage et peinture ???
elle est pas là
In Austria we call it "purer Pfusch!" ig de clutch is wrong and is that paper tape as sealing?
Nice video! Small tip: If you bolt or clamp down the engine during disassembly, the video becomes more pleasant to watch.
Добрый день наконец новый выпуск 🔥
The am6 engine is a good engine... But for me RK6 for life!!
could you tell what foam this is to remove the rust?
just painting and cleaning! replace seals and bearings??????
He could at least have replaced the piston, given its condition I'm sure it is blocked
Am6 engine, easy to work on and very powerful with some performance parts such as 100cc 2fast 😈
That's a minarelli am6 engine. Not a "dt50 engine".
And i'm suprised that engine runs for 10 minutes after the treatment you gave it. Would've probably been better off just getting it started.
could have washed the engine on the outside first before disassembling it.
Am5/6 mineral right.? Have the same
For your info engine is called minarelli AM6, Im running exact same engine and exact same condition as this and it doesnt need a restoration tbh
Restauration without replacing any part with new one
Hey by the way I would not use that air filter because I have had experience with them before and they don’t filter sand or dirt they do flow good but the flow to good but good job it looks really good for what it was.
yea they let all the sand in through the spots where they missed to glue.
can you restore 125cc Lifan ????
OMG the Oseal condition for head
And adjust gasket paper on case
Pleased make a Honda CX 500 v 2 engine🙏🙏🙏🙏🙏🙏🙏
Ahhh, I get it now. Reman only means washed and repainted. R&R: remove and repaint. Always wondered what that meant.
Hoće li biti nastavak sklapanja krosera ili samo motor
Precise restoration, congratulations 👌.
Thank you for the like 😀.
Qual o tipo de tinta spray esse rapaz usa? queria pintar o motor da minha moto tambem.
No bearing changes or hone ?
how do we know if the engine works ? 😋
don't work, at all
Great restoration. That piece is a beautiful 😄😄
head gasket go brrrrr, it will not last a day
Amazing
What years and country were these sold in?
first start?
Top top a galera do brasil curte seus videos
pelo amor de deus, o video tá todo errado, ele não fez uma coisa direito, o cara diz que restaurou mas só limpou e pintou, até mesmo a junta da tampa superior o maluco reutilizou num motor que já teve ter mais de 20 anos de uso... não cara, fale por si só, ninguém mais no Brasil deveria curtir uma praga dessas
Does it work?
this video reminded me something, do not judge on appearance
That's a new engine with exterior dirt
Minarelli am6 put a tpr 86 tuning kit on it
Opening from the piston rings are facing to the exhaust. That won´t last long.
sealants,bearings ?
The engine is not build by yahama, it may come from a yahama but its built and provided by minarelli. (minarelli am6).
Qlq sait ce qu'il utilise pour faire partir la peinture
Pq ngm fala que esses vídeos são tipo asmr dele trabalhando nisso ? Os barulhos e tals
Esos aros de pistón ayer estaba andando
L’embrayage a mal été monté il est bon à démonter pareil pour les roulements 🥱
Мамкин рестовратор 😅
Pourquoi remonter un piston dans cet état avec ses segments ?? pignon de sortie de boite hs aussi et la boite à clapets et j'en passe..... bref....je serai curieux de le voir passer au banc après la "restoration"....
What's that liquid you clean the crankcases with at 6:00?
aluminum does not have this red rust, this is probably just water and dishwasher soap
It's just a cosmetic restoration. He left old bearings, old filter, old beaten up piston etc. Very bad example of restoration, made just to make a nicely looking engine, not nicely working one. Shame.
Satu lagi, dia lupa mengatasi karat pada gigi rasio
Padahal itu sangat beresiko ke yang lainnya di dalam mesin untuk jangka panjang 💀
@@HerryHero mungkin yg punya gak mau ganti bang, takut biayanya mahal.. 😂
Bueno, tanto trabajar en el motor, para dejar rodamientos viejos y poner una junta entre los semi cárter, este motor no lleva junta sino pasta de juntas. Pero para disfrutar de un vídeo de "restauración" ha estado bien 👌🏿
Awan subscriber na hahahahaja
Да он внутри как новый выроботки почти нет, поменял сальники и уплотнители и пробегает ещё). Вот японцы технологично делают, продуманная конструкция. Один недостаток это патрубоки из карбюратора к лепестковому клапану лучше цельным такие детали делать проблем с подачей топлива не будет и мельше деталей.
ржавые звёзды кпп👌👍
The good Old am6 engine. My absolute favorite engine ever produced
nice video but you didn't build the block correctly the head gasket is not reusable if in that state and the clutch lid wasn't put on in the correct direction. the way you blocked the flywheel by the crank is just wrong. the intake manifold is so old that you should not reuse it and you did not properly install the case
crankcase locator bushings?
In Germany we say Pfusch 😂
what to use to clean the engine? I mean this liquid
Veramente questo ha lasciato i paraoli e i cuscinetti senza cambiarli? Robe da matti
Is he wearing the gloves wrong way round ?
The textured side is meant go on the palm side of your hand
What product do you use for the oxid?
dishwasher soap
magneto installed incorrectly
what product do you use to clean the block?
i recommend gasoline or brake clean
Result ??
C’est bon je suis énervé
Why not change worn parts?
Just wash it all and sand blast it ALL
Where is the start?
Oops bro forgot to change the bearings 😂
Nettoyage carburateur c'est en option
Isn't the carborator hose very crooked?
imagine doing an restoration and ending up with rustier internals than before. i would also tighten that cilinderhead a bit more, if youn want it to break, better do it good
Motor start???
Tu as oublier la rondelle de calage sur le barillet et ont ne met pas de joint intercarter sur am6 mais pattes à joint dirko
Nice job
How to darud sandstorm your engine
nice job👍👍👍
Great job
Yamaha.aprilia.rieju y alguna marca mas. usaba ese motor.... minarelli 😂❤