Top 15 Plastic Repairing Tips and Hacks That Work Extremely Well
Vložit
- čas přidán 14. 12. 2023
- Hello everyone! You are watching video "Top 15 Plastic Repairing Tips and Hacks That Work Extremely Well"
I hope you enjoy watching my video!
► Subscribe: bit.ly/Creationholic
On Creation Holic channel, you can learn various inventions, science projects, crafts and DIYs teaching how to reuse or recycle.
© Copyright by Creation Holic ☞ Do not Reup
#diyprojects #plastic #tips #welding #plasticwelding - Jak na to + styl
Greetings from Brazil and thanks for sharing! I made my first repair yesterday, using stapler clips for anchoring a broken fan base. But I have 2 suggestions: 1) Please emphasize that the glue must have low (or very low) viscosity; 2) Please add a warning that melting plastic can generate toxic, asphyxiants (such as carbon monoxide), or even poisonous substances (such as cyanide), depending on its composition.
Hello! thanks for your comment. Wish you all the best!
Cuál es el súper pegamento en Argentina...?
7d5d😮7dddxxxxxxz 13:21
@@crismorales6147 cualquiera como el loctite o super bonder, o la gotita de poxipol. Tienen que ser pegamentos cuyo ingrediente activo sea cianoacrilato.
@@crismorales6147 la gotita (si es que existe todavía) - o cualquier cianoacrilato
Wow!? I wish I knew of these methods earlier in life...thanks for this. Extremely useful ways of repairing split, cracked or broken plastic. So helpful
😂que bueno estoy aprendiendo mucho me alegro
Gracias por colaborar conmigo que Dios te bendiga
@@MariaCastillo-yi1ub ¡gracias por la respuesta! Dios bendiga y te deseo lo mejor en el nuevo año
Glad it was helpful!
7😊
เยี่ยมเลยครับ ได้ความรู้การทำพลาสติกที่แตกร้าวให้กลับมาติดสนิทแน่นใช่งานได้ต่อไปอีกนานโดยไม่ต้องไปหาซื้อมาเปลี่ยนใหม่ให้เปลืองสตางค์ขอบคุณครับที่เผื่อแผ่ความรู้ที่ดีๆให้กับเพื่อนพ้องน้องพี่จากฅน ครวรรค์
Thanks for sharing your amazing techniques.
Over the years, I've done simple plastic welding using fine stainless steel mesh for reinforcement, but you've shown so many more useful techniques, that I'm bound to use one day. Thanks much.
Glad you like them!
@@creationholic101 What kind of tape are you using?
Не могу дать ответ,так как нет возможности перевести комментарий 🙏.
Merveilleux de voir comment vous vous y prenez que de créativité !
Sir you nailed it by showing amazing technics and self made tools and baking etc I was using common salt 4 repairing with Super glue Bravo ❤❤❤
6/15 tip for fixing a broken gear totally ROCKS! Love it! This tips video would be even better if you identified what type of plastic each was made from and which mix you use for which kind of plastic. That would put this video over the top as best plastics repair video!
We used to use a hot air plastic repair gun (not homemade) to repair cracks in polypropylene. I suspect that you can use any thermoplastic to repair others of the same kind. These are excellent ideas. If you can, experiment with different ideas. Then use the best on the real job. Notice that the video uses mostly baking soda or heating the plastic using the same plastic for fill. Baking soda seems to work better than other materials on plastic. I haven't had much luck with graphite but haven't tried too hard.
Thank you! Cheers!
the gear wheel probably was made from polyoxymethylene.
I hear pure dryer lint (with no softener contamination) is the bee's knees when used appropriately
The gear idea is ingenious, awesome all the way 🤙🏼
Alguna de tus ideas me parecen absolutamente geniales. Y las pondré en práctica en algunas reparaciones que tengo pendientes.
Gracias por tu contenido
Saludos desde Madrid, España
Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
"Absolutely brilliant! I've struggled with plastic repairs in the past, but this video has opened my eyes to a whole new world of possibilities. The use of materials like clay, charcoal, and even metal wires for reinforcement is genius. Kudos to the creator for such innovative solutions!"
You're very welcome!
@@creationholic101 what type of clay you use? is that polymer clay? plasticine clay? or the real clay?
Great creativity
Those are great tips, I have been repairing things for 50 years and I still learned stuff from you. I use more standard epoxy for strength, again strenghting it with metal screws etc., and use bluetak to mould it. My other thing to use to strenghten the joint is fibre glass tape. You are officially a "Fix-it fairy". To explain this, other people go off and do mundain things, and when they come back, it is all repaired, and they are amazed.😮
Thank you! Cheers!
@@creationholic10132:36
Really have made me feel like breaking plastic parts so I will have to fix it myself absolutely brilliant thank you for your advice and skills!
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
As a rc enthusiast I must say thank you for all the great ideas since 90% of the breakage I deal with are plastic ❤
fyi heating nylon (most strong parts of flexible plastic in RC) makes it very brittle! Do not try and repair your RC chassis with the metal hoop melted in shown here.
I've looked into it at length and there's no real feasible way to "repair" broken nylon plastic parts, the only solvents that come close are dangerous and not easily available to the public and I'm unsure how well they'd work for a repair. The best "fix" for broken nylon parts is to use metal or other plastic to make a "brace" of sorts with a flexible glue around the broken area, or by drilling new attachment points to add the brace.
Basically Nylon doesn't "wet" with glue and is a nightmare to glue even in industrial assembly when they have perfect conditions. It's also flexible which is a nightmare as a lot of glues are not!
@@trif55 thank you for the info every bit of knowledge gained is a benefit 👍
@@tifflynn2215 I went back down this rabbit hole a bit, it looks like I was using Nylon 6.6 so maybe Nylon 6 doesn't embrittle as much with heat?
Thanks for sharing!
One of the most informative videos I have ever watched. Thank you @creationholic101
Yes, you are a genius plastic surgeon ! I was completely astonished. Thanks a lot for the ideas. From Rajshahi, Bangladesh.
So nice of you
Making essentially an epoxy or plastic adhesive using ACETONE to break down the polystyrene (cd case) was one of the best things I've ever learned. Being able to make your own epoxy/adhesive for plastics is just freaking awesome.
2 questions though...
How strong is the hold? I am not using it for any life critical objects but still want to know if itll hold/bond for a good period of time or is this just like a band aid fix?
How long does the mixture stay as a grl before hardening?
Asombroso, espectacular. No solo felicito al instructor y técnico, felicito también a esas MANOS que no están nada lejos de las de un Cirujano Plástico. Hasta pronto, Gonzalo Lopera desde Medellín (Antioquia) COLOMBIA.
Thank you for the new information and ideas. We enjoyed it. I am from Jordan
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Hello, I'm from Portugal, You are very ingenious! I was very impressed with the forms of restoration and reconstruction shown in the videos you made.
Hello! Welcome to Creation Holic channel. I am very happy to read your comment. Have a good day!
From the islands or main land
Great creativity
This guy has skills that everybody should learn : repairing minor breaks with whatever is available. Good job mate.
Thank you! Cheers!
😂
Гениально все!!! Золотые руки!!! Браво Мастеру!!!
Thank you! Cheers!
Maravilhoso, ótimas ideias com resultados satisfatórios.
Ip uçları süper
Hello! I am very happy to read your comment. Have a good day!
Belo trabalho. Vou tentar a técnica do 1º vídeo para uma tv quebrada. No 14º vídeo, após a lixagem, pode-se pulverizar um pouco de wd40 ou similar, para dar um acabamento homogêneo na peça. Saudações do Brasil e feliz ano novo.🇧🇷
Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
Excelentes videos e aprendido mucho quisiera que hicieras un vídeo para pegar ornamentos de plástico para acuarios felicitaciones
WOW! So many brilliant ideas 💡! You cannot stop watching this video! Thank you very much! I feel able to fix any plastic part now. 💪 👍
I'm glad you enjoyed this project! Feel free to connect with other viewers in the comments section and share your results. It's always inspiring to see what everyone creates
جزاك الله خير
كنت قادرا على إجراء الكثير من الإصلاحات عدا البلاستيك لم تكن لدي مثل هذه الأفكار المذهله
زادك الله فهما ومعرفه
I am glad you like this ideas. Wishing you all good things!
By golly, I'm supposed to be good at this stuff, but you outdid me by miles. Kudos to you sir! Btw, I'm from the Philippines. Thank you.
Hello! I am very happy to read your comment. Have a good day!
You can never stop learning in life.
Excellent tips and tricks! I learned some new tricks!
Instead of staples I suppose you could use small washers. Also, making your own wire staple from wrapping a wire around a screw is brilliant!
Taking a piece of copper tubing and then making it fit into the soldering tool and then being able to push a cable tie through is brilliant!
WOW!
I'm glad you enjoyed this project! Feel free to connect with other viewers in the comments section and share your results. It's always inspiring to see what everyone creates
You are truly the plastic surgeon ! Genius 👍👍👌🏿👌🏿
Thank you! Cheers!
🤣🤣🤣
Get outta here! Actually pretty cool though . Plastic surgeon coining ? You're at the top of your whits aren't you?
Sometimes being the God of plastic can be a good thing. Thanks for the tips. 😘✌️
Great creativity
De Bordeaux en France. J'ai réparé avec de l'acétone et du plastic une coque de rétroviseur de voiture. Depuis 5 ans, parfait. Je ne connaissais pas les autres astuces. Merci.
Hello! thanks for your recommendation. Wish you all the best!
For a clever fella, you break, quite a lot of things, some great content and some great ideas 😊😊
Glad you enjoyed
😂😂😂
Hahaha
Yo creo que él ya se volvió el arregla todo de la familia y amigos
The first of these kind of video's I have seen that actually have useful ideas.
Thank you! Cheers!
Usted es un genio. Gracias por compartir sus conocimientos, me han servido mucho y ya no tengo que botar las cosas que aún pueden servir. Un abrazo desde Colombia
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
كلمة واحدة عمل رائع
De verdad te felicito, me gustan las personas creativas e ingeniosos como tú, aportan utilidad y aprendizaje a las personas, felicidades
Hello! Welcome to Creation Holic channel. I am very happy to read your comment. Have a good day!
Thanks for your teachings. This is a real help for the planet, by repairing plastic objects instead of throwing them away.


Comentarios
Thanks for your teachings. This a real help to the planet, by repairing plastic objects instead of throwing them away and polluting. I watch your channel from Chile.
بارك الله بكم وجزاكم الخير
Parabéns pelas restaurações lindo trabalho. Eu também amo restaurar mas me falta tanto material. Aos poucos vou adquirir. Gratidão por ensinar. Sou de S.Paulo.
Thank you for watching
플라스틱 용접하는 것 나도 알리서 사서 이 작업 해보아서 압니다.
성취감도 있고
대단하십니다 ㅎㅎ
I've been repairing plastic car parts for a long time but I learned a LOT tonight!!! Thanks!
Glad it helped!
You pretty much covered everything! Great job It is very important to know many of these tips for people like me who tend to try to DIY everything.
Glad it was helpful!
Es muy maravilloso tu enseñanzas mi amigo yo soy de México
Lo encontré x casualidad y voy en el tercer arreglo y me encanta. Ahora no tengo mucho tiempo Para terminarlo d ver pero lo veré después gustosa. No keria irme sin Felicitarte y agradecerte compartir tus habilidades. GRACIAS
Hello! I am very happy to read your comment. Have a good day!
Great tips. It would be interesting to know the types of plastics you are repairing and using in the repairs (ABS, Polypropylene, styrene, PET, etc.) It would also be interesting to know how many watts the soldering irons are.
ABS and PP plastic
soldering iron 60w
Wow, this is a eye opener. Thanks for sharing. Great instructable. Best i have seen for a while on CZcams! The whole is nagging over plastic. This is a great way to fix things. 😊
Great work - I consider myself a good repairman, but this is sweet !!!
Glad it helped!
Gracias genio por compartir sus conocimientos de restauraciones en todo tipo de plástico bendiciones 🙏🙏🙏
Thank you! Cheers!
De Xelaju Guatemala . Te felicito eres un genio y gracias por enseñarnos. Eres nuestro maestro .
Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
Brilliant. It's often worth to try repairing things before throwing them away.
Glad you like them!
Some techniques I haven't seen before, particularly the use of acetone to create a liquid patch. The baking soda/superglue trick I knew from Marty's Matchbox Makeovers. Adding reinforcing metal I've seen before on Toy Polloi. One technique he often uses is to sculpt missing material out of epoxy putty. He also custom builds parts out of styreen sheets and lego.
Thanks so much for watching our video. Wish you all the best
The acetone trick is commonly used for filling cracks in 3d printed parts. The multiple methods for reinforcing plastic welds with wire, screen etc is great and solves an age old problem I’ve had with weak repairs. Great video
The best skills and tutorial video I've seen in new year 2024,, thank you for sharing this,, this is what an internet supposed to be...
Great video so many times I've just replaced parts what a loss of money.
Dang. All the stuff I threw out and replaced when I didn't need to. Genious! Thanks for posting!
Glad you like them!
This video makes me want to go and break something just so I can fix it. Absolutely genius! 👏👏
Thank you! Cheers!
I've used soldering iron to press in staple-gun staples to bridge cracks a couple times, though one of my fave methods is putting plastic cable ties into a glue gun and using it just like a glue, or filling in holes!
إذا أردت النجاح:
1- لا تفكر أبداً في المناصب، اجعل همك الوحيد هو عدم العودة.
إذا أردت النجاح:
2 - لا تضيع الوقت، فالوقت ثمين جداً وعمرك محدود بصلاتك، ونومك، وقيامك، وعملك، ووجباتك، وعلاقاتك، وتمارينك.
إذا أردت النجاح:
3- لا تنتظر حدوث معجزة، ولا تنتظر الفرص لتأتي، أنت من يصنع الفرص.
إذا أردت النجاح:
4- لا تشتكي من ألم التمارين الرياضية وطعم الطعام كالأطفال. انت محارب. تطوير شخصية تظهر الصبر والتكيف. بغض النظر عن مدى اضطراب كل شيء، تكيف معه وتغلب عليه.
إذا أردت النجاح:
5- الاستمرار في النهوض بعد السقوط. أنت أقوى مما تتخيل. كل، نم، مارس الرياضة، ابتسامة مبهرة مرعبة تكشف أنيابك القاتلة، وثقتك بنفسك، وعضلاتك التي لا تقهر. أنت، نعم، أنت الذي تقرأ، خلقت لتكون بطلاً.
6- كثرة الاختلاط بالناس . يمكن أن ينمي ذكائك الاجتماعي وستصبح ذو خبرة في التعامل مع الناس، لكن عقلك لن يبدع في أي شيء (فاخلطه دون الكثير).
7- جعل شخص ما قدوة لك هو عمل يحطم روحك تمامًا
اجعل من نفسك السامية قدوة لنفسك فقط، فأنت لم تخلق غبيًا بالفطرة، بل جمود عقلك وميله إلى أن يصبح شخصًا معينًا هو ما أدخل الغباء في عقلك.
8- العلاقات المكثفة. احذر من أن تجعل شخصًا أساسيًا في حياتك. اقترب مما تريد، لكن ضع في اعتبارك فكرة غيابه عنك يومًا ما حتى لا تتدمر آلية تفكيرك.
9- احذر أن تصبح كما يريد الآخرون لك أن تكون. لا تقم بتعديل أو تغيير أو تغيير أي شيء عن نفسك وحياتك.
بدلاً من ذلك، عش بالطريقة التي تعتقد أنها الأفضل لحياتك.
Plastic zip ties into a hot glue gun? Wouldn't that ruin the glue gun??
😅😅😅I tried it and the plastic strap didn't melt
His glue gun must be like furnace 😅
@@Cloony4u It does have temperature control, but really you just have to wait for the glue gun to get up to full temperature before doing so, as the plastic does have a slightly higher melting temp than the glue sticks!
КЛАСС... Как всегда здорово, очередной лайк.
Thank you! Cheers!
Wow, that broken fender hole is EXACTLY what I commented on the previous video I watched you do..... Gr8 minds think alike 🤣😂😁😇 After watching ALL of hem, you sir are simply BRILLIANT.
Sono Roberto, da Brindisi Italia. Devo confessare che sono rimasto molto sbalordito nel vedere questo video, molto bello e moltissimo utile per quei lavori. Bravo e grazie ti tutto.
Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
I like the gear repair idea a lot. Creating a mold of good teeth out of wax. Clever but simple to implement. Kudos.
Glad you liked it!
Украина город Александрия. Вопрос как по прочности шестерёнки и что даёт графит в смеси с содой?
Спасибо большое ВАМ за идеи!
I'm glad you enjoyed this project! Feel free to connect with other viewers in the comments section and share your results. It's always inspiring to see what everyone creates
Nossa valeu muito assistir todo, essa última dica era a que eu mais precisava 👏🏾👏🏾👏🏾👏🏾
Hola.. Maravilloso lo que enseñaste me encanto y es de muchísima utilidad.. grcs mil grcs.. bendiciones..
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Cool! Never know when such ideas will blend together to make a fix!
Hello, you are so kind to leave me a comment! If you have any other better ideas, please share them with me! Wishing you health and happiness always!
We need more of this. People need to stop throwing away things so much
Hello, you are such a nice person to have left me a comment! With a dream to contribute to making the world a better place, I really need good and useful ideas and solutions! If you have any other great ideas please share with me! Together we will make this world a better place! Wishing you good health, success and happiness! Thank you very much!
Q significa en español
Hi there! A great inspiring video in so many ways! I have a gear of diameter of about 5 milimeters, I think not possible to fix the way you fixed your bigger one, but thinking how to duplicate to have a new one, clay and some mixture would be they way I guess
Sensacional. O Campeão da gambiarra em plástico. Muito bom. Parabéns.
Thank you! Cheers!
Very good demonstration of how to repair your Honda fairings. Most Honda owners would find this useful. Maybe even the occasional KTM owner too.
Glad it was helpful!
These were all very useful tips. Thank you for your time ❤
Glad it was helpful!
Очень интересные решения из подручных материалов. Благодарю!
Glad you like them!
You're greatest. I'm never know what can we do with plastic surgery - repair. Many achievements from Croatia. 😊👍🏼
Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
One of the best repair videos of any kind I've seen!
Hello! I am glad you like this ideas. Wishing you all good things!
Great creativity
Espectacular trabajo! Muy ingenioso! Muy valioso tu video! Soy de Formosa - Argentina, encantado de aprender tus consejos! Sigue así éxitos
Hello! Welcome to Creation Holic channel. I am very happy to read your comment. Have a good day!
Muy bien. Felicitación y gracias por regalar conocimientos. Desde BOGOTA, Colombia.
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
Adding reinforcement is necessary as when melting the plastic for repairs, the carbon content increases making the repair area more brittle. Spot heating the area with concentrated heat VERY careful to not deform the piece and then so the repair can help, but is not always feasible.
Thank you for sharing your feedback . Have a good day!
Great ideas and skills! Wonderful. I do not think I have the courage and skill to do repairs like you do, but still I enjoy watching!
what are you ten? it doesnt take courage or skill to use a soldering iron on plastic
Thank you very much!
Im from the Phillippines...thanks a lot for this tips on repairng plastics..Very helpful..
Thanks for watching!
And that I am Iranian. I do art work (visual arts), my main field is painting and I love doing performances and techniques that others are unable to do! This satisfies me a lot
Great stuff man👍👍 What super glue do you use? I used many in my projects and none of them seems to be as good as yours😂
cyanoacrylate adhesive glue
@@creationholic101 Thank you.
Antennacable was new to me. What a great idea. Thxalot..
Glad you like them!
Thanks for sharing your amazing techniques, they are great.
Glad you like them!
Fantastic ideas, I already have a few broken items to fix! This should be fun and save money too.
Hello! I am glad you like this ideas. Wishing you all good things!
Very smart repairs of plastics!!!!
Best regards from Hellas (Greece)!!!
Thank you! Cheers!
Hi from South Africa🇿🇦 ,thanks for all of the ideas i can really make use of each one of the. Simply genius👌
Thanks so much! 😊
謝謝分享，過程中真的學習到很多知識和技巧！
I'm glad you enjoyed this project! Feel free to connect with other viewers in the comments section and share your results. It's always inspiring to see what everyone creates
It was very informative, creative and practical, thank you ❤
Glad you like them!
"Cheers, that's why CZcams is so great. You can't find such in-depth knowledge anywhere else. Thanks for that!"
Hello! Welcome to Creation Holic channel. I am very happy to read your comment. Have a good day!
I used fiberglass with fiberglass mesh for strength on my motorcycle fender cracks. Very Strong repair. ALWAYS drill a small hole at the end of any crack as this will stop the crack from getting any longer. I also have used JB Weld (Original 24hr cure time) with great results. Having said all this I enjoyed your video and learned a lot of new tricks, 😊 Thanks
Hello! thanks for your recommendation. Wish you all the best!
一看再看都看不膩，好療癒，想起我的鋼彈，我的機車殼，有這些好方法可以修復，就非常開心😍
Glad it helped!
Ótimo video. Suas dicas são maravilhosas. Vou colocá-las em prática. Parabéns. Tupiara -Rj
Hello! I am very happy to read your comment. Have a good day!
Caramba! Excepcional sua criatividade! Parabéns! Gratidão por compartilhar seu conhecimento!
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Soy de P.R. y me encanta mucho el vídeo.Te felicito y gracias por compartirlo.😊
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Excellent video with great ideas. I was familiar with some of the repair ideas, but the ones I hadn't seen before were super. Subscribed
Glad it was helpful!
I am a mechanical engineer and you are a genius ! - Thank you . . .
Thank you! Cheers!
Buenas noches .soy Alejandro d Habana Cuba .quiero aprender todos esos detalles proyectos ( manualidades) gracias .
A real "plastic surgeon"!
There is no way your a mechanical engineer. This guy used a cotton ball and super glue on the very first thing. That's horrible..
I have been working with plastics in the automotive industry for 30 years, in Fiat, GM, and Ford. I have post graduated studies in plastics, I was proffesor at the University and I worked for Dow Chemical and Union Carbide . . . I think this man is a genious !
Primeiro video com reparos realmente faceis de fazer e funcionais... muito bom.
Glad you like them!
(Quick question at the end)
This is awesome, I'm only 6 tips in and must comment how brilliant these tips are. I always try and fix broken plastic stuff, and sometimes successfully, but always messy and crude. Having the proper techniques is obviously key, many thanks for these!! Question: what are those metal stickers? They look very useful, would love to get my hands on those!
Those silver sticky pieces are from a roll of Foil Tape, from any hardware store, or harbor freight tools store.
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Probably should put a disclaimer when you're melting the plastic and the fumes are coming off to at least wear a respirator.
I've been painting for 25 years so I know about these things 😢
Yes, I agree to you. Smoke is very harmful to us
Exelente aportacion.
Hello! thanks for your comment. Wish you all the best!
Using cement powder instead of graphite is much better and stronger. 😊
Hello! thanks for your comment. Wish you all the best!
Creo q se trata de usar lo q esta a al alcance de la mano en ese momento.
What is the graphite supposed to be doing? Is it somehow reacting with the cyanoacrylate ?
Cok faydali bir video. Cok begendim. Tesekkurler.
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Juda yaxshi. Omad tilaymiz. Tashkent Uzbekistan
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Better than most. Superglue based repairs are marginal at best. It does not truly bond. It's easy, but not really that good. Low strength.
Most of the thermal repairs are good but using wire ties as filler is most often going to be the wrong type plastic use the parent material scrap and shavings instead, That will be compatible, other materials may not be. Better to get a real adjustable plastic welder. Thermal is almost always best to retain strength and it can be reinforced,
Solvent based repair using acetone may be ok, buy solvent based glues are usually better
Thank you for sharing your feedback . Have a good day!
Lots of awesome ideas you have I always used E6000 to get the job done fixing my broken tiny whoops and micro quadcopters because super glue is just not impact resistant but maybe I will give it another shot using your techniques
Thank you for sharing your feedback. Have a good day!
I'm gonna say this, almost all of these are a "If you have no alternative". Number 10 especially can be done with that same piece they cut and pair of couplers. No need to spend time with super glue or cutting the pipe into pieces. In most cases when you use heat to melt plastic you are almost always guaranteed to make it weaker or more brittle. These techniques can work in applications where there will be no stress on said items for long durations.
Ay South América we are so poor that need this kind of "Works". Believe me.
@@gladispenalver3278 I do understand. Especially when parts aren't available.
Hey if you continue, the whole bike will be made from backing-soda and super-glue 😄 👍
😅😅😅 Thanks so much for watching our video. Wish you all the best
😂😂
Gá😊
😅
😅
Excellent presentation of your smart solutions to plastic repairing! Many regards from 🇬🇷 GR !
Glad you liked it!
I'm from Iran.
Thanks for sharing ideas 🎉
Thanks for watching!
Great creativity
Super Glue and carbon, cotton, or baking soda are good for cosmetic repairs. For longer lasting strength, I recommend Epoxy vs Super Glue. CAs are brittle and lose strength significantly over time.
I was saying this on another reply about repairing RC Cars which are often Nylon Plastic, you're better off building a brace or additional structure with metal or fibreglass and epoxy
Hello! thanks for your recommendation. Wish you all the best!
Bravo ❤
😮88o6o8😮o8😮
Hello! I'm from Ukraine! Now our people are resisting aggression from Russia, which attacked our country! Thanks for the interesting video! Your ideas helped me a lot. Peaceful skies and prosperity! 🇺🇦 🇺🇦 🇺🇦
Stay strong, stay safe! Greetings from Poland.
149.200 Volga. You loose anywhere and anytime
Your president is a crook. Just like ours 😂
Olá vc esta de parabéns com suas ideias fantásticas continue assim meu caro amigo., eu também faço varias aventuras e mim viro nos trinta fazendo varios consertos... Kkk mais é claro porque sempre busquei a mim aperfeiçoar com vcs que já são profissionais em varias artes.
Vc está de parabéns ! Eu soude ARACAJU-SE
Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
Vidéo très complète pour toutes sortes de situations. Très utile, vraiment.
I'm glad you enjoyed this project! Feel free to connect with other viewers in the comments section and share your results. It's always inspiring to see what everyone creates
I am from Armenia🇦🇲
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best