Fuji Turbine Sprayer Basics Turbine HVLP Spray System 101
Vložit
- čas přidán 15. 07. 2024
- All the basics on Turbine based HVLP sprayer systems featuring the Q5 Platinum from Fuji. Included topics are setup of the sprayer, filter cleaning and turbine unit maintenance, and an introduction to the spray guns available including the T70 bottom feed, and T75G gravity feed... both with pressure assist. Probably the standout feature of the Q5 Platinum is the variable speed output. Control the air pressure at the turn of a dial, up to a capable 9.5 PSI.
Q5 Platinum with T75G Spray Gun... amzn.to/3IJLhD7
Q5 Platinum with T70 Spray Gun... amzn.to/3IJLzdb
T75G Gravity Spray Gun Only... amzn.to/3g5EZl8
T70 Bottom Feed Spray Gun Only... amzn.to/35kAzVa
Or shop my entire curated collection (Shop Tested) on The Thoughtful Woodworker Storefront…
www.amazon.com/shop/thethough...
As an Amazon Associate I earn commissions, and am grateful for your support.
Learn all you can about turbine based spray systems here, and make an educated decision... fujispraysystems.com/
Thanks for watching The Thoughtful Woodworker! We appreciate your patronage, and you the viewer make this free video content possible. Subscribe to The Thoughtful Woodworker for all the latest woodworking content.
#woodworking - Jak na to + styl
Thank you for this video. It was very informational and exactly what i needed after buying a mini might 5. The sprayer is great but the manual leaves a lot to be desired.
Thanks and good luck with your sprayer!
If it's just the knob and little wedge shaped spacer, it just threads on to the shaft of the lever. If the whole shaft came out, it's more complicated.
Just bought a new system. Thanks for the advice!
That's great Carlos! Hope you enjoy the new sprayer.
Wow, that q5 platinum is quiet. Your videos are very helpful.
Thanks!
This is the best explanation I’ve found on this! Thank you!!
Awesome! Thanks for the positive comment.
Best
VERY nice video! I just received a Q5 and you hit the nail on the head for what I’m using.
Thanks! Enjoy your new Q5.
I just got my Q5 and your video was very helpful. Thanks for all the detailed explanation. I will be firing it up this week to apply a finish on a spalted maple slab. Thanks again!
Sounds like a great project. Enjoy the new Q5, I think you'll like it. Even at perhaps 60% power it sprays most finishes great.
Execellent video. Just received my Q5 and needed this.
You will love the Q5 turbine. Very nice system. Enjoy!
Thanks, I have been agonizing over which HVLP sprayer to get. I had done a fair amount of research, then saw your video. I just ordered the Q5 with the T70 gun and subscribed:).
Good choice on the Q5 and T70 gun. That's my preference as well.
Best
Even though my system is an Earlex, your walk-through is one of the most helpful I’ve seen and applicable to both systems. Thanks for a thorough, detailed explanation.
Okay cool, glad there was some info relevant to the Earlex.
Have fun with it!
great video
Thanks!
Thanks for the very nicely done video. I am close to pulling the trigger on one of these to be used for painting vintage motorcycle parts. I've been priced out by the pros so need to do it myself. 👍
I know what you mean. The system will pay for itself in 2-3 jobs.
Good luck deciding on a system.
I'd get the Q5 again. No regrets here.
Very interesting video. Blessings
Thank you!
My pleasure. Thanks for checking out the video.
Thank you! 👍
My pleasure!
I understand that the company changed name to EURO AIR.Viewing from the French island St Martin in the Caribbean. Thank you for sharing
Hmmm, I haven't heard anything about a name change. They continue to do business as Fuji in Canada and the U.S.
Best
Thank you for sharing. I am quite familiar with the turbine System. I have my turbine from Volume Air France I am unable to find the replacement parts for the Gun
Great video on this product! Liked and subbed. Just pulled this unit out of the box and will be spraying SW Gallery series paint on some cabinetry I made. Any input on which nozzle size is appreciated!
Hi Andy, I would spray with the 1.5mm aircap set for a fine finish that builds more slowly, or a 1.8mm aircap set to move a little quicker. The typical advise is to use a 2.0mm aircap set, but I think it plasters the paint on too thick. If you're using the Q5, you'll really like it. I remove that black inline valve, and just set the variable speed on the turbine to about 80% or so. Good luck on your project!
I purchased a Craco Croix Turbo X8, it is in perfect condition, I have a couple of gravity HVLP guns that have the traditional air hose, can I simply switch out the quick connect fittings and use the gun with the turbin and hose?
No, I don't think that would work. Turbine spray guns operate on high volume and very low pressure (usually 7-9psi). Compressor driven conversion guns usually operate at 30-35psi. You'll probably just have to buy a gun designed for your turbine.
Best of luck.
Is there an in-line pressure gauge that be installed right before the gun? It'd be nice to know just how much pressure you have for different types of coatings that will be used...
There is an in-line valve to control airflow. I took mine off, because the Q5 is variable speed. It's easier for me to just dial in the airflow on the turbine. If you're looking at a turbine without variable speed, the valve might be useful.
@@TheThoughtfulWoodworker Oh no, I meant an actual gauge where you could read how much pressure is going to the gun. I've seen this gauge on some of the automotive pneumatic spray guns. It's great the Q5 has the variable pressure knob, but for those of us who haven't been spraying for years and can't find the right pressure by ear or through a bunch of trial and error, having a visual for psi would be nice.
@@xxdemonshitxx there's no pressure gauge, but with a turbine you really don't need one. Airflow is constant on most models, and you adjust fluid control to suit the situation.
Best
Are these ideal to spray spindles on a porch or airless sprayers are better for that?
They both would get the job done. I have a Fuji Q5 as well as an airless sprayer. I use the airless for painting the house, so I'd probably just use an airless for painting a deck railing. Best of luck!
This is the 3rd man I’ve watched on CZcams who pronounces it turban. It’s Turbine. Turban Is what the 9-11 hijackers did not wear on their heads. 🤨
I suppose I do mispronounce it. I'm not sure if I can change my ways now, but consider it duly noted. Thanks.
Hello I'm new to spraying. Why would you use your Q5 over your airless? I don't understand why people own both quite yet.
Yeah, good question. The airless is good for painting a house, but it doesn't produce a fine spray pattern. Plus, the airless is a lot more work to clean up because it pulls paint through the hose.
With a turbine sprayer there's only paint in the cup. It only takes about 2 minutes to do a full clean.
Best
I want to purchase the 3oz cup for my Q4 What would the part number be? Thank you
There are several cups available, depending on what gun you have. Go to Fujispraysystems.com and choose products, parts and accessories, cups. There you can choose the 3oz cup you want.
Best
@@TheThoughtfulWoodworker I went on the site and I cannot find the correct one. Mine is the Q4 T75G
@@nancyhoekman6706 I only see the 3oz cups for the siphon feed guns. Same on Amazon. You might have to call them to see if it's available for the T75G.
Good luck!
turbin.
my mini mite 4 is not very loud.
That's good to hear. I'm also happy with how quiet the Q5 is as well.
Have fun spraying.
My mini mite 4 is very loud compared to the q5 platinum
@@spkendrick Yes, any of the Q models have extra soundproofing and engineering for no direct sound path from the turbine. They will run quieter than the standard models. In addition the Q5 has variable speed.
Thanks for checking out the video.
Best
Good video. But you wear a turban. You paint with a turbine. lol, No worries. lots of love.
Yes I've heard that before. Even when I'm conscious of it, it's just one of those words I mispronounce. Best to you.