Huge thanks for this - only took me 5 mins once I knew to pull the lower corner into the engine compartment a bit. (Feel chuffed with my little self now).
So many thanks for posting this - you saved my NYE! I found the hardest part reseating the unit - being winter I was paranoid I might split the plastic bumper grille but mercifully I didn't (wonder how many new ones Ford have happily supplied!). Also lucky that the failed dip beam bulb was a standard H7 55W for which I had a spare.
Thank you for this. I've just changed both of my headlamps and there's no way I would have been able to remove the headlamp casing without the 'trick' with the inside corner. You've just saved me a painful trip to Halfords and £18!
Great tutorial my friend. A month ago i watched another tutorial and it helped a little bit when i changed the light bulb but it didn’t show the tricks that you used. I spent 40 mins changing the light bulb because it was hard to get it out and even harder to get it back in. It sucks that i first connected the light bulb and then put it in its place that’s why the light bulb was a little bit off when i drove the car. Today i had some time to finally put the light bulb correctly and did it in 10 minutes with the help of your tricks. Thanks again for the tricks and the tutorial
Thats great. Thanks for the tutorial. I have a dead wide bulb i have to change. Also on the same side the main hulb only comes out n after i tive it a bunp on yhe outaide. I hope its just a loose connection.
And now that you’ve handled the globes with your bare fingers they’ll blow very soon due to the oils on your hands! 🤦♂️. Always use gloves or clean with spirits!
Huge thanks for this - only took me 5 mins once I knew to pull the lower corner into the engine compartment a bit. (Feel chuffed with my little self now).
So happy to hear this, thanks. Well done, you !!
So many thanks for posting this - you saved my NYE! I found the hardest part reseating the unit - being winter I was paranoid I might split the plastic bumper grille but mercifully I didn't (wonder how many new ones Ford have happily supplied!). Also lucky that the failed dip beam bulb was a standard H7 55W for which I had a spare.
So happy to hear this. Glad I could help. Happy holidays.
Thank you for this. I've just changed both of my headlamps and there's no way I would have been able to remove the headlamp casing without the 'trick' with the inside corner. You've just saved me a painful trip to Halfords and £18!
I'm so happy to hear this!
Thank you for this, my Mondeo's headlights got water in them so needed to know how to remove them, thanks DIY!
Glad I could help. Good luck.
Great tutorial my friend. A month ago i watched another tutorial and it helped a little bit when i changed the light bulb but it didn’t show the tricks that you used. I spent 40 mins changing the light bulb because it was hard to get it out and even harder to get it back in. It sucks that i first connected the light bulb and then put it in its place that’s why the light bulb was a little bit off when i drove the car. Today i had some time to finally put the light bulb correctly and did it in 10 minutes with the help of your tricks. Thanks again for the tricks and the tutorial
Comments like yours make me truly happy. Thank you.
Thats great. Thanks for the tutorial. I have a dead wide bulb i have to change. Also on the same side the main hulb only comes out n after i tive it a bunp on yhe outaide. I hope its just a loose connection.
Happy to help.
Thanks for this! Watched the video once and managed to change the bulb under 10 minutes without a hitch :) would be a real hustle without your tips.
Glad to hear this. Happy holidays.
Great job, thanks a lot 😊👍💯
Happy to help. Thanks.
Clear and straightforward - thank you.
Very welcome. Thank you.
Thanks!!
It was a little trick the first time with the inner corner. I carefully used a flat screwdriver to "bend" the corner in or out.
Well done! Glad I could help.
Very usefull thank you for the tutorial sir!!!
Glad I could help.
Great video, thanks
No problem, thanks.
Very helpfull thank you
Happy to help
My tab broke on the connector, wtf do i do 😢
That sucks... :( I suggest you tape it in place and then a replacement..?
The connections at 02:05 are not on my headlamp - all I can see are some posts - why is this?
Do you have Mondeo mk4? Strange, the headlight must ve connected, it should be there. Could it have broken off, by any chance?
my tab is broken and i’m not able to get the connector out
☹️
Is not easy to put it back...But i did it(thank fuck)😊
Well done, mate 😀
And now that you’ve handled the globes with your bare fingers they’ll blow very soon due to the oils on your hands! 🤦♂️. Always use gloves or clean with spirits!
Never happened. But thanks.