If you put the water outlet port in the top of the boiler tank and use an elbow outside the burn chamber, it will allow you to completely fill the tank with water and gain that top surface as a heat transfer surface. If you put the water bucket higher than the boiler tank and keep the upper port in the tank completely under water and remove any ups and downs in the feed lines this will Thermosiphon with a steady flow instead of batch boiling and squirting large gulps of boiling water. With a boiler that large and a trapped air pocket at the top, the volume of boiling water it could blow out could actually be quite dangerous. This boiler is large enough, you could probably heat 2-3 buckets of water simultaneously with good thermosiphon. Nice build!
@@franknada8235 the way they put the water pipes in the boiler chamber all the air cannot escape so there is no water touching a good portion of the boiler surface inside the burn chamber, so not as much heat transfer as they could get. If you don’t flow enough water it will boil in the boiler and escape, possibly violently into that bucket. If they put the water outlet from the boiler on the top of the boiler instead of the side, and raised the bucket upward, it might thermosiphon with a steady flow and heat the water without boiling in the heat chamber. Thermosiphon is powered by the water density change in relation to gravity. Hot water, and air want to go up, not sideways. So any sideways travel will slow thermosiphon flow and make it more likely to boil in the chamber.
Дурило! Ты чьи слова повторяет? Хоть знаешь где на карте Европа. С середины сентября работает отопление и все остальные прелести. Знаю что говорю, Я здесь живу.
You are very creative and thanks so much for sharing your ideas with the world and may the good Lord bless your heart ♥. Lastly you need to change the plastic bucket for an iron bucket or so..😊
Muchas gracias por su respuesta,el primer nivel y el último con la chimenea lo entiendo, lo que me sorprende es el 2dp nivel el más importante para mí,mi interrogante es: solo por los dos agujeros sale el calor que viene del primer nivel donde está la leña sube x el conducto central del segundo nivel y sale el calor se transmite por las mangueritas y calienta el agua?,o lo que pienso es que ud al llenar el agua al balde este se traslada al encapsulado del segundo nivel sellado y el agua se calienta?disculpe nunca hice un proyecto así,soy neófito en la materia,pero me gustan hacer las cosas bien y quiero hacer uno igual a su proyecto y si tiene algo más que agregar ,se lo agradezco de antemano
Hola, esta estufa calienta el agua muy rápido, si cocina sopa de más de 5 litros, el agua en el cuerpo de la estufa se cocinará antes que la olla de sopa.
Votre poêle à bois combiné à un réservoir d'eau! Est remarquablement ingénieux, peut-on augmenté le volume d'eau, bien-sûr que cela doit prendre un peut plus de temps pour que l'eau chauffe? Vous m'avez agréablement surpris avec votre chef d'oeuvre, merci pour le partage formidable! 😊👍
Wow great work another new idea to extract or get light from burner same time all three in one work done same time.and also waste heat used to radiate tha air radiator for heat rome.
Thank you for sharing your DIY build. This may have been already suggested, and if it has, no worries then, but I would highly suggest that you use a stainless steel, metal container or a non BPA plastic container for your water reservoir on the build. The extreme heat to the water would cause the plastic from the bucket to leech into the water over time and you'd be using water adulterated with endocrine disrupting things that act like estrogen. DYOR and you'll see what I mean. Just looking out for you and showing appreciation and concern for someone who I imagine wants to keep his T levels where they should be. May the Heavenly Father bless you if it is His will, or have a cheers in greeting if that's your preference. Take care.
You can also run a water filled, room radiator off the system as well? No need for all of the technical welding etc; just install a long coiled 1.2 m x 12mm copper coil pipe in the heating chamber?
Great System and Well done . I live in Germany . If i build such a Heater it is okay . But if i start it i have much much problems . That oven is against any green rules it is not Bimsch V2 and so on. But that dont matters. A good meal a warm house and warm water. Live can be very good in bad times 😉😉😉😉😉😉😉
Мастер высокого уровня ! Но 2 проблемы зола сыпется в низ это крайне не безопасно когда несколько раз протопите все не много поведёт. И 2 прослужит не долго быстро прогарит дно
Нужно взять пробку от бутылки вина и вставить в ручку крышки алюминиевой кастрюли. Тогда можно брать крышку кастрюли и не обжить руку. Старый советский рецепт)))
esta buena la idea para tener un radiador casero y se aprovecha el hecho de que pasa al tarro asi no genera presion en el sistema ya que no esta sellado
Like a very big biolite that makes hot water perfect offgrid system add a couple of thermo electric generators and store in a battery to power fans and water pumps and charge electric devices
If you put the water outlet port in the top of the boiler tank and use an elbow outside the burn chamber, it will allow you to completely fill the tank with water and gain that top surface as a heat transfer surface. If you put the water bucket higher than the boiler tank and keep the upper port in the tank completely under water and remove any ups and downs in the feed lines this will Thermosiphon with a steady flow instead of batch boiling and squirting large gulps of boiling water. With a boiler that large and a trapped air pocket at the top, the volume of boiling water it could blow out could actually be quite dangerous. This boiler is large enough, you could probably heat 2-3 buckets of water simultaneously with good thermosiphon. Nice build!
Thank you very much, wish you and your family, always be healthy and happy
Nice talk
Huh?
@@franknada8235 the way they put the water pipes in the boiler chamber all the air cannot escape so there is no water touching a good portion of the boiler surface inside the burn chamber, so not as much heat transfer as they could get. If you don’t flow enough water it will boil in the boiler and escape, possibly violently into that bucket. If they put the water outlet from the boiler on the top of the boiler instead of the side, and raised the bucket upward, it might thermosiphon with a steady flow and heat the water without boiling in the heat chamber. Thermosiphon is powered by the water density change in relation to gravity. Hot water, and air want to go up, not sideways. So any sideways travel will slow thermosiphon flow and make it more likely to boil in the chamber.
@@rronmar ok thanks I understand you better now 👍🏻
Гибочный станок зачётный!
Большое спасибо
Вроде как полуторку осилил, при длинне около 0,7 метра.
Great bit of kit and video done so well. Thanks for showing I have gas bottle stove on my boat I am thinking of converting. Cheers, Pete
Thank you very much, wish you and your family always healthy and happy, and soon have a kitchen like your wish
Ну наконец-то нормальный контент подъехал
Impresionante me he quedado sin palabras. Bravo maestro.👏👏
Muchas gracias, deseo que usted y su familia se mantengan saludables y felices.
That is amazing. Brilliant work 👏🏻
Thank you so much, wish you and your family stay healthy and happy
A excellent job on the build! So very cool!🙂✌🏼
Thank you so much, wish you and your family stay healthy and full of happiness
@@CreativeCementIdeas Your welcome! Luv&Peace Cheers! ✌🏼
Fantastic construction of a wood stove and water heater. Brilliant 👍
Thank you very much
Да,скоро вам это понадобится 👌
Спасибо
Shwvwjwbwjq ghahahabb HAHAHAHHAHAHAHAHHAHAHAHAHAHAHAHHAHA
Вещь!!! 👍🏻
Очень актуально этой зимой, особенно в Европе и на Украине… 🤷🏼♂️🔥✌🏻🚀
Большое спасибо
Автор даже прикола не выкупил
@@raccoonvid9665 😁
Жертва телевизора?
И в России, где дровами топятся целые регионы
Clearly DIY but also master level craftsmanship.
Thank you so much, wish you and your family always healthy and full of joy
Very clever and talented man ! 👌👌👌
Thank you so much, wish you and your family always healthy and full of joy
Amazing. Thanks.
Thank you very much
Wow amazing work 💯🔥
Cool project though!
Технически довольно сильно продуманная и практичная технология.
Спасибо большое, здоровья и счастья
ロケットストーブに鉄砲風呂をつけるというアイデアが素晴らしい
どうもありがとう、あなたの健康と幸せを願って
Great job !
Thank you so much, may you and your family stay healthy and filled with happiness
Great idea, thanks
Thank you so much, wish you and your family stay healthy and happy
the good part is you will never be iron deficient
This comment made my morning look
Inflation is killing me and I can't afford food
made me laugh for pointing out its obvious flaw, but hook a radiator or a bathtub and you got a nice little system!
You are so amazing 👍
Thanks for sharing 🙏
Thank you so much, wish you and your family always healthy and full of joy
Excellent job but not easy for every one.
Bravissimo , idea geniale 👍👍👍👏👏👏
Grazie mille, auguro a te e alla tua famiglia tanta salute e felicità
@@CreativeCementIdeas grazie altrettanto 👍👍
Occhio, in Italia è illegale.
Le stufe e caloriferi devono avere certificazioni
Amazing!
爐子與熱水器的完美結合
非常感謝
Актуально во всех городах Европы этой зимой)))
Благодарю вас
Дурило! Ты чьи слова повторяет? Хоть знаешь где на карте Европа. С середины сентября работает отопление и все остальные прелести. Знаю что говорю, Я здесь живу.
У нас в Сибири каждую зиму актуально
Большое спасибо
Да и в Красноярске тоже всю жизнь😆))
Wow bhai ji kya baar hai bahut badiya
Thank you
They sped it up and cut it but, you know that man spent forever on those welds
Very well job 👍
Thank you so much
You are very creative and thanks so much for sharing your ideas with the world and may the good Lord bless your heart ♥. Lastly you need to change the plastic bucket for an iron bucket or so..😊
Thank you very much, I am very happy for your comments
Muchas gracias por su respuesta,el primer nivel y el último con la chimenea lo entiendo, lo que me sorprende es el 2dp nivel el más importante para mí,mi interrogante es: solo por los dos agujeros sale el calor que viene del primer nivel donde está la leña sube x el conducto central del segundo nivel y sale el calor se transmite por las mangueritas y calienta el agua?,o lo que pienso es que ud al llenar el agua al balde este se traslada al encapsulado del segundo nivel sellado y el agua se calienta?disculpe nunca hice un proyecto así,soy neófito en la materia,pero me gustan hacer las cosas bien y quiero hacer uno igual a su proyecto y si tiene algo más que agregar ,se lo agradezco de antemano
Hola, esta estufa calienta el agua muy rápido, si cocina sopa de más de 5 litros, el agua en el cuerpo de la estufa se cocinará antes que la olla de sopa.
Ёмкость с водой лучше поднять повыше, а верхний шланг сделать немного выше нижнего, чтобы можно было воду сливать до этого уровня.
I like the idea.
Tks you so much.
Damn good stuff
Votre poêle à bois combiné à un réservoir d'eau! Est remarquablement ingénieux, peut-on augmenté le volume d'eau, bien-sûr que cela doit prendre un peut plus de temps pour que l'eau chauffe? Vous m'avez agréablement surpris avec votre chef d'oeuvre, merci pour le partage formidable! 😊👍
Merci beaucoup pour vos commentaires,
Beside the nice project, I must congratulate to you 'bout your welding skills👍👍😁
Thank you so much
Youd b putting wood in this ALL Day!
Awesome. You nailed it!
He weld it
@@alexborg9105 agree!
Top video , top Arbeit , Danke für video
Vielen Dank, ich wünsche Ihnen und Ihrer Familie, bleiben Sie gesund und glücklich
@@CreativeCementIdeas besten Dank , wünsch ich ihnen auch. Lg Rolf
Exelente!! 👏👏👏
Muito obrigado
Magnifique idée !
Merci beaucoup
Its so professional....
.
The pipes could be connected to radiators for free heating too
Thank you very much for your comments
В нашей стране до сих пор используют такую технологию для обогрева своих домов
Спасибо большое
Скоро и в Европе будут такую технологию осваивать.
@@EgorKyznetc вам бы прекратить смотреть Киселева и им подобных недожурналистов
Эту технологию используют везде, особенно на западе где нет центрального отопления ))
@@EgorKyznetc а что зато надежно, сколько надо столько и сжег дров, а то платишь круглый год за коммуналку хрен пойми за что и какое качество воды
ವಾವ್ ಸೂಪರ್ 👌ತುಂಬಾ ಚನ್ನಾಗಿ ಇದೆ ತುಂಬಾ ಇಷ್ಟ ಆಯ್ತು ಸೂಪರ್ 👌🥰🌹
ತುಂಬ ಧನ್ಯವಾದಗಳು
LOGISCH, KOMPAKT, STABIL, EIN "INTELLIGENTER" UND "RAFFINIERT" GEBAUTER ALLESKÖNNER; SEHR GUT!!!!! LGheike_v.P.....
Vielen Dank, ich wünsche Ihnen und Ihrer Familie viel Gesundheit und Glück
@@CreativeCementIdeas 👍🌹🤗DANKE DITO !!!!!LGheike_v.P.....
Valla süper
Elinize sağlık
Çok teşekkürler
Back in ussr, welcome ❤
Thank you
Wow great work another new idea to extract or get light from burner same time all three in one work done same time.and also waste heat used to radiate tha air radiator for heat rome.
Thank you very much, glad you commented, wish you and your family good health and happiness
Use White Ceramic material as mental light bc it shine when heat up
ชอบความเป็นระเบียบเรียบร้อย
ขอบคุณมาก
Superb angle grinder skill
Thank you very much
I like your homemade break press
Thank you
Делайте творити все у кого есть возможность . В руках сила
Большое спасибо
Говно конечно и не эфекктивно но вы делайте
This stove burns cleaner than my new one with the A + sticker 😅
Thank you so much
Utilísimo, autosuficiencia
Muchas gracias, deseo que siempre estés saludable y feliz
👍🖐️💯💯💯💯💯Bella manualità
Grazie mille, auguro a te e alla tua famiglia tanta salute e felicità
Top Job 💪
Thank you so much, wish you always healthy and happy
Excelente trabalho 👏👏👏👏👏
Muito obrigado, desejo que você e sua família fiquem saudáveis e felizes
Отлично . ракетная печь в модернизированном виде. актуально сейчас.
Большое спасибо, желаю вам и вашей семье быть здоровыми и счастливыми
사고싶네요 너무좋을것 같아요
이 제품을 좋아해주셔서 대단히 감사합니다. 아쉽게도 판매하지 않습니다.
Thank you for sharing your DIY build. This may have been already suggested, and if it has, no worries then, but I would highly suggest that you use a stainless steel, metal container or a non BPA plastic container for your water reservoir on the build. The extreme heat to the water would cause the plastic from the bucket to leech into the water over time and you'd be using water adulterated with endocrine disrupting things that act like estrogen. DYOR and you'll see what I mean. Just looking out for you and showing appreciation and concern for someone who I imagine wants to keep his T levels where they should be. May the Heavenly Father bless you if it is His will, or have a cheers in greeting if that's your preference. Take care.
Yes I will have to replace some details, Thank you very much for the comments, wish you good health and happiness
@@CreativeCementIdeas It's my pleasure. Likewise the same to you as well.
You can also run a water filled, room radiator off the system as well?
No need for all of the technical welding etc; just install a long coiled
1.2 m x 12mm copper coil pipe in the heating chamber?
Thank you very much, I am very happy for your comment, wish you and your family always healthy and full of joy
Интересно, медь не прогорит? Лучше чугунный радиатор туда приспособить, но это другой размер печки будет. Тут интересно что переносная.
讚讚讚!
Great System and Well done .
I live in Germany .
If i build such a Heater it is okay .
But if i start it i have much much problems .
That oven is against any green rules it is not Bimsch V2 and so on.
But that dont matters.
A good meal a warm house and warm water.
Live can be very good in bad times 😉😉😉😉😉😉😉
Thank you so much, wish you and your family stay healthy and happy
Мастер высокого уровня !
Но 2 проблемы зола сыпется в низ это крайне не безопасно когда несколько раз протопите все не много поведёт.
И 2 прослужит не долго быстро прогарит дно
Большое спасибо
😲 neat!
Thank you
Надо назвать так : Скоро во всех домах Европы!!!!))))))) хаха))))
Sangat bagus dan multifungsi..
Terima kasih banyak
Сначала подумал, будут делать самогонный аппарат своими руками😅
Большое спасибо
Nice skills
Thank you so much
Bác có thể chế bếp đun trấu tự động cháy liên tục , ko phải thay trấu ?
Và chỉ để đun nước phục vụ hệ thống sưởi sàn nhà như bên các Nước Hàn Đới
👍👍👍
Cảm ơn bạn rất nhiều vì gợi ý của bạn, chúc bạn luôn mạnh khoẻ và hạnh phúc nhé
아이디어가 멋집니다. 그런데 물 속에 재가 섞여 들어갔네요. 끓인 물은 어디에 사용합니까?
정말 감사합니다만 재는 물에 섞일 수 없습니다
Мастеру за проект и работу, что изделия, что ролика лайк и звоночек!
Большое спасибо, я очень рад за ваш комментарий, желаю вам всегда быть здоровыми и счастливыми
Актуальненько для Европы и Цэевропы!
Bon travail
Merci beaucoup, je vous souhaite, à vous et à votre famille, de rester en bonne santé et heureux
I wouldn't be surprised if they share the production lines in the factories as DIY soon.😂
Thank you, I made this kitchen by myself
It is recommended to heat the water in the hose, for example, instead of heating the water directly!
It is the same as a ship's boiler
Thank you so much
Grazie per il suggerimento. C'è un modo di mettere una fragranza profumata che si sente nel esterno che copre odore del fumo
Awsum. “;-)👍👍👍👍
Dankie
建议电焊的时候弄个黑幕挡一下。电焊的光十分影响观看效果。
非常感谢你,我很高兴你的评论,祝你健康快乐
Great project, especially in a near WWIII scenario ahah
Thank you so much
Amazing
Thank you
Nice for Blackout to have a shower🤩😅
Hi, have you watched the entire video?
@@CreativeCementIdeas oh sorry, im stupid, the whole chamber fills up with water, im edit my comment...
Thank you very much, wish you and your family stay healthy and happy
어렸을적 쓰던 연탄보일러와 원리가 같군요
진심으로 감사드리며 가정에 항상 건강하시고 행복이 가득하시길 기원합니다
Нужно взять пробку от бутылки вина и вставить в ручку крышки алюминиевой кастрюли. Тогда можно брать крышку кастрюли и не обжить руку. Старый советский рецепт)))
Спасибо большое, мне очень важно ваше мнение
esta buena la idea para tener un radiador casero y se aprovecha el hecho de que pasa al tarro asi no genera presion en el sistema ya que no esta sellado
Muchas gracias, me alegro mucho por tu comentario.
Heating water on a stove is how people used to wash.
Thank you so much
Дуже корисна річ, дякую за якісний контент ❤️🇺🇦
Щиро дякую, бажаю Вам і Вашій родині бути здоровими та щасливими
Fantastico
Grazie mille
It's efective but it's still not efficient... I hope there's a way to make a stove which can use the excess heat for a better use...
차후에 물탱크안 녹발생할수 있어서 동관을 쓰는게 좋겠네요
대단히 감사합니다
Самое время для Европы 😅 этой зимой будут пользоваться
Благодарю вас
Какую квадратуру помещения способна обогреть данная печь? Спасибо
Like a very big biolite that makes hot water perfect offgrid system add a couple of thermo electric generators and store in a battery to power fans and water pumps and charge electric devices
Thank you very much, I am very happy for your comment, wish you and your family good health and happiness
@@CreativeCementIdeas what a lovely response I wish your beloved the same!
Это стоит того чтобы так заморачиваться?
I like it
Thank you
Для квартиры - самое то!😂😂😂
Большое спасибо
Котелок надо было с нержавеющей стали. Ржавчина будет. А так как отопление гаража очень даже
Большое спасибо
砂輪機要切圓,有那麼容易嗎?
想知道師父們的意見
你好,切圓的時候要換切石,切石直徑小
This looks really awesome and I like it but Why are you not actually welding it together why do you keep tacking everything?
Hi, I soldered all the parts except the bucket and the two faucets
Европа спасена!
Благодаря ти много
تحية أطيب من الطيبة ٠٠٠ أطلع على نظرية عمل المراجل البخارية ٠٠ فإنك ستبدع أكثر ٠٠ وتصنع موقد ( تدفئة ومرجل وطاقة كهربائية ) ٠٠٠ شكرا اااااا جزيلاً اااااا للاحرار ٠٠٠
خالص الشكر لك ، أطيب التمنيات بالصحة والسعادة