How To Replace the Clutch on a Yamaha Blaster 200
Vložit
- čas přidán 16. 03. 2022
- Yamaha Blaster Clutch Replacement | www.rockymountainatvmc.com/Sa...
Does your clutch feel like it's slipping, chattering, or just not operating correctly? It's most likely time to replace it, or at the very least, inspect the clutch components for wear. So, in this video we show you the proper procedures to replace the clutch on a Yamaha Blaster 200. The steps shown will be similar for Yamaha Blasters from model year 1988 to 2006, but check your OEM service manual if you are unsure of procedures or specifications.
Click Here To Subscribe To Our Channel!
/ @rmatvmc
Follow Rocky Mountain ATV/MC On Social Media!
FACEBOOK: rmatvmc?utm_...
INSTAGRAM: rmatvmc?ut...
TWITTER: RMatvmc?... - Jak na to + styl
After replacing my clutch didnt work so i watch your video and most probably that ball has been lost so i have to look for it now. Thanks btw
This guy knows what he is talking about. Very professional. Thank you. Your video is #1 on CZcams.
Thanks for the video
Nice !!! 😊 thanks
Thanks for the helpful tutorial.
Dziękuję
What would I need to do if the clutch is not engaging
hell yeah
2001 Yamaha blaster won’t start after full rebuild any suggestions or help will do all good parts
Check gas and spark!!
What are those gears in the back called ?
I have a question, I replaced all the clutch plates on my blaster but I missed the part of the video of the part where I was supposed to offset all my metal clutch plates. I honestly stacked em all with the tan facing up…. Havent fired up the bike. What’s the outcome… ? I would have to purchase another gasket again I’m guessing..?
The reason you space out the tab on the steel clutch discs is to cut down on vibration. You may notice some vibrations with them all facing the same way. There is a chance your gasket won't come off in one piece (and it is safer to use a new one every time) but since the gasket hasn't been on there long, it may be fine to reuse in this situation.
What oil should I coat the clutch parts with?
Soak the clutch plates in your choice of transmission fluid. We show 3 different options you can use at 1:00 in this video.
Please do the transmission🙏🏼🙏🏼🙏🏼🙏🏼🙏🏼🙏🏼🙏🏼
Should the clutch actuator be easy to push
I have the same problem
if u dont have a magnet tilt the bike
Hey Charles, wanna do some videos on an Xr650r motor? I need the left case replaced and I can send the motor.
Unfortunately we don't plan on rebuilding one of those right now. Thanks for the offer though! -Charles
@@rmatvmc it was worth a shot. Keep up the good work.
@@rmatvmc where can I get a magnet like that
Could you do a full motor rebuild for a crf150rb
I'll look into it. -Charles
@@rmatvmc thank you
Where did u get that magnet from
This was one that we have had lying around the shop but you should be able to find a similar one at your local hardware store.
You mention in the beginning to refer to the service manual. Later when the push rods are installed you say coat with oil, where the service manual specifies lithium soap based grease..... Kind of contradictory and divergent wouldn't you say? Otherwise good informative video
We mention the manual so you can make an informed decision on weather or not to use lithium soap base grease or oil. I don't think it will make much of a difference to be honest. Other than that, I hope it helped out. -Charles
You should have pointed out that they are two bolts longer than the rest. Than showed with hole they belong in.
Edit........ I didn't see in the beginning where you said it. But still have pointed them out tho. Should have showed them when taking them out and pointed out where they belonged.
Thanks for the input! We will try to be more clear about that stuff in the future.
Where can I get that magnet too
Tool*
What's the length of the pushing rods?
The push rod 1 is 1" and the push rod 2 is 4"
@@rmatvmc I'm from RSA please use cm/mm
1-25.4mm
2--101.6mm
I just measured the rods 1 and 2 are not the sizes you gave me or the size you gave the the actual expected sizes?
Then wish one goes in first?
Does anyone know what the little round thing on the back side of the pressure plate is called. You can see it at 10:11
Are you referring to the push rod?
What would I need to do if the clutch is not engaging