MASSEY FERGUSON TRACTOR HYDRAULIC LEVER SETTING | Massey Ferguson hydraulic repair |

MASSEY FERGUSON TRACTOR HYDRAULIC LEVER SETTING
हाय दोस्तो मे आपका दोस्त Abdul kurad दोस्तो आज मे आपको इस वीडियो मे MASSEY FERGUSON TRACTOR HYDRAULIC LEVER SETTING के बारेमे बताऊंगा तो आपये वीडियो सुरु से लेके अंत तक देखना और आपको वीडियो पसंद आये तो हमारे और किसान भाईयो मे सेर करना और लाईक करना तो बिल्कुल भी ना भूले और दोस्तो मे आपके लीये नई नई वीडियो लाता हु और लाता रहूंगा तो आप हमारे इस नेक काम मे हमारे साथी और सह भागी बने और दोस्तो आपने अभीतक हमारी चैनल Abdul kurad को सब्सक्राइब नही कीया तो अभी करले दोस्तो चैनल को सब्सक्राइब करने से मनको भी आनंद की अनुभूति होगी धन्यवाद Abdul kurad

[@paidipalalakshmi4346]

a.b.kured.bahi.tera.samjaneka.tarika.bohat.acchahi.jajakallh.qahyr

[@rajendrasinghgogadev7441]

उस्ताद जी इस विडियो में तो बहुत ही अच्छी जानकारी दी है आपने

[@AbdulKurad]

बहुत बहुत धन्यवाद सर जी आपका 🇮🇳👍🤝😊

[@devayanideshmukh2998]

आभारी हूँ. आप बहुत अच्छा काम करते है.नमस्कार. शुभ रात्र

[@rajendrabhagat788]

आपने कितना आसान तरीका से समझाया ऐसा समस्या मेरा ट्रेक्टर में पंद्रह सालों से था मेकेनिक लोग ठीक नहीं कर पा रहे थे आपको कोटी कोटी धन्यवाद

[@AbdulKurad]

बहुत बहुत धन्यवाद सर जी आपका 🇮🇳👍

[@gagokalsi4849]

sri g pa ka namber nahi aa send karo ga

[@parkashtechnicalguru8777]

आप इतने अच्छे से विडियो के माध्यम से किसानों मदद करते हैं आपक कोटी कोटी धन्यवाद

[@AbdulKurad]

You welcome Sir thanks 👍🇮🇳

[@kalyansinghsingh3834]

सर जी आपका यह विडियो हमारे को पसन्द आया ऐसे विडियो दिखाते रहे मै आपका सह्रदय सवागत करता हु कल्याण सिह चौहान

[@AbdulKurad]

Thank Sir Ji 🇮🇳👍🤝😊

[@mahbubkhan6339]

Aap Hamare liye bahut mehnat karte ho Aapka kaam mere ko bahut achha lagta hai sir

[@AbdulKurad]

Sir aap jese mahan logoki duva multi he sir jazah kallah 🇮🇳👍😁

[@prdippatel5056]

Good job Abdul bhai dhanyvad 👌👌👌👌

[@AbdulKurad]

Thanks pardip bhai 🇮🇳👍😁

[@ravidevsinha4308]

Bahut badiya kaam karte hain sar

[@AbdulKurad]

Dhanyvad sir aapka 🇮🇳👍😁

[@swadeshpan1366]

Thanks you sir Naresh Jagran guru dev🙏🙏🙏🙏🙏🇮🇳🇮🇳

[@AbdulKurad]

Bahut Bahut Dhanyawad Sir Ji 🇮🇳 👍🤝😊

[@omjangid3550]

काम की जानकारी दी है अब्दुल भाई

[@AbdulKurad]

Dhanyvad sir aapka 🇮🇳👍😁

[@jitendratavniya73]

omaram jangid अब्दुल भाई आपका नम्बर दिजीये मेरे ट्रेक्टर कि हैड्रोलीक खराब है,,९६६९७५४६५५

[@KS-cu1zc]

Abdul JI can you do some repairs videos on Universal tractor{Fiat} 550&640 hydraulic setting & clutch ,brake job or engine service. love the way you teach thx

[@aloknatia7532]

Hello sir main aapka bahut bada fan hun sar aap jis tarah samjhate Hain Na koi bhi koi bhi Insan achcha se samjhe jaega

[@AbdulKurad]

Thanks sir ji 🇮🇳👍🤝😊

[@santoshmahto2108]

Thanks❤ for me🙏🙏 अब्दुल भाई जी

[@AbdulKurad]

Thanks sir ji 🇮🇳👍

[@jagdishbandhiya9159]

Khub khub dhanyvad bhai Kishan mate video banavva bdl aabhar sarji bahut acha he video

[@AbdulKurad]

Khub khub aabhar saheb ji dhanyvad 🇮🇳👍

[@rajeshraut5604]

Very important this video Sir thanku

[@AbdulKurad]

You welcome Sir 🇮🇳🚜😁

[@Akshaykinge]

Thank you ustaad ji ❤️❤️❤️❤️....

[@AbdulKurad]

You welcome Sir ji thanks you 🇮🇳👍😊

[@djs0ngremix25]

Abdul Kurad Great Ap Logo Ko Thik krke Dete ho Ap ka dhanywad 💕😁

[@AbdulKurad]

You welcome Sir 🇮🇳😁

[@djs0ngremix25]

@@AbdulKurad ap Kaha Se Ho G

[@AbdulKurad]

Sir me Gujarat se hu OK sir thanks 👍

[@vinodrai8768]

Thanks for replying am realy very happy to hear you

[@AbdulKurad]

You welcome sir ji thanks you 🇮🇳👍

[@ashokkumarkaushik1880]

बहुत अच्छे हाइड्रोलिक के बारे में लीवर के बारे में अच्छी जानकारी प्राप्त हुई हमें धन्यवाद भैया चलो लीवर के बारे में कुछ तो पता चला पहले अनजान थे स्लो फास्ट के बारे में

[@AbdulKurad]

You welcome Sir thanks 🇮🇳👍😁

[@singhfarmerz578]

@@AbdulKurad sir ye jo liver setting ke liye weight lgta hai ye kitne kg ka hai btaye sirr

[@singhfarmerz578]

Sir weight btade kitne kg ka hai me bi tractor mechanic ka Kam krta hmm

[@AbdulKurad]

@@singhfarmerz578 4 Paune Ka Hota Hai

[@singhfarmerz578]

@@AbdulKurad thanks ustaaad ji

[@neerajtractor5463]

Sir main aap ki har video dekhta hu

[@AbdulKurad]

Good sir ji thanks you 🇮🇳😊👍

[@indamangaming7397]

Thanks for you 😌 god bless you 😌

[@AbdulKurad]

Thanks sir ji 🇮🇳👍🤝😊

[@krishnasable9817]

Guruji very very good👍

[@AbdulKurad]

Dhanyvad sir aapka 🇮🇳👍

[@KAMLESHKUMAR-ff6bn]

Kamlesh up

[@AbdulKurad]

Thank Sir Ji 🇮🇳👍🤝😊

[@JSPatel-yz2lo]

Good abdul bhai 👌👌👌👍

[@AbdulKurad]

Thanks sir 🇮🇳👍😁

[@javidpatel4478]

Good job Abdul bhai

[@AbdulKurad]

Thanks sir 🇮🇳👍

[@vinodrai8768]

Sir Massey Ferguson 245 93 model ke hydraulic lift nka lever ki setting kaise hoti hai batane ki kripa kijiye.

[@AbdulKurad]

Sir ji kabhi uska job aayega to banaunga ok sir ji thanks 🇮🇳👍🤝

[@NareshJangra108]

Thanks Abdul bhai 👍🇮🇳🚜🚜🚜🚜

[@AbdulKurad]

You welcome ustad thanks 🇮🇳👍😁

[@Arjun-bu9fe]

Uttar Pradesh Bar

[@Arjun-bu9fe]

Hindustan hydraulic fitting

[@javedkhokhar5027]

Very Nice work

[@AbdulKurad]

Jazah kallah bhai 🇮🇳👍😁

[@kaushikhandique1117]

very helpful video sir👍,i am from ASSAM Sir😊

[@AbdulKurad]

Good sir ji thanks you 🇮🇳👍

[@amanpreetsinghgill2134]

Sir 245 mark ki liver setting ki video v laye

[@AbdulKurad]

Ok sir ji kabhi uska job aayega to banaunga ok sir ji thanks 🇮🇳👍🤝😊

[@swadeshpan1366]

Thanks you sir🙏🙏🙏🙏🙏🙏🙏🇮🇳🇮🇳

[@AbdulKurad]

Thanks Sir Ji 🇮🇳👍🤝😊

[@MRGMECHANIC]

Nice

[@AbdulKurad]

Thanks malaram 🇮🇳👍😁

[@punitbhaipatel2234]

Abdul Bhai aapka kam bahothi acha he aor aapka samjane ka tarika bhi bahot hi accha he aasani se samaj me aajata he aesehi video ham kisano ke liye banate rahna ise hame kafi sahai milti he aapka dhanyvad abdul khai👌🏽👌🏽👍

[@AbdulKurad]

Punitbhai aapka bhi bahot bahot dhanyvad 🇮🇳👍🚜😁

[@NaseemKhan-bd3pi]

Abdul Bhai hamari lift bhi bhut awaz kr rhe h implement jodne pr

[@vincenzo_freefire670]

Salamwalekum Abdul bhai

[@AbdulKurad]

W Salam Sir Ji sukriya 🇮🇳👍🤝😊

[@ashishbhuva115]

Good sir

[@AbdulKurad]

Dhanyvad sir ji aapka 🇮🇳👍

[@dheerajkumarbhardwaj2932]

dahut sundar sir

[@AbdulKurad]

Dhanyvad sir aapka 👍

[@sunilsonawne7307]

Good job bhai

[@AbdulKurad]

Thanks you sir ji 🇮🇳👍😊

[@ravichaudhari6914]

Super sir

[@AbdulKurad]

Thanks sir ji 🇮🇳👍🤝😊

[@indiacph51]

Very nice bro

[@AbdulKurad]

Thanks you sir ji 🇮🇳👍

[@ihsanmehmood9649]

Good job dear

[@AbdulKurad]

Thanks you sir ji 🇮🇳😊👍

[@chhatrasinhpateliya5061]

Very good

[@AbdulKurad]

Thanks sir ji 🇮🇳👍🤝😊

[@vipulbhaisarodiya1870]

Abdul Bhai namaste aabhar

[@AbdulKurad]

Dhanyvad sir aapka 👍

[@imrankurad5625]

Good job

[@AbdulKurad]

Jazah kallah bhai 👍😁

[@k.hparmar8410]

વાહ અબ્દુલ ભાઇ વાહ

[@AbdulKurad]

Thanks sir 🇮🇳😁👍

[@ramcharankashyap7746]

@@AbdulKurad ki ap apna mobile no dene ka kirpa karoge

[@tusharpatel8191]

હાડ્રોલિક નુ કામ ખૂબ સરસ રીતે થયું છે અબ્દુલભાઇ આવુ કામ તમારા જેવા સારા કારીગરજ કરી શકે છે.👌👌👌👌👌👌👌👌

[@AbdulKurad]

Dhanyvad tushar bhai KAKA na tractor nu hydraulic nu su rijelt che 🇮🇳👍😁

[@tusharpatel8191]

@@AbdulKurad hydrulic ok che

[@AbdulKurad]

Thanks tushar bhai 👍😁

[@heeraram2518]

Aapka kaam aacha hai iselye aap price batna

[@ramnarayanlodhi6915]

Good 👍👍👍👍👍

[@AbdulKurad]

Dhanyvad sir aapka 🇮🇳👍🚜

[@MithuKumar-hd8kr]

सर आपका nambar चाहिए आप कहाँ रहते है हमारे ट्रेक्टर में ये सारे परेसानी हैं और कितना पैसा लग जायेगा plase रिप्लाई कीजिये गया आपको बहुत बहुत धनयवाद

[@AbdulKurad]

Sir ji me Gujarat palej se hu ok sir ji dhanyvad aapka 🇮🇳👍

[@vijujithakor4267]

Good

[@AbdulKurad]

Thanks sir 🇮🇳👍😁

[@pushkarpatidar5949]

245कादैखनाहै

[@saurabhlodhi345]

हम भी ठीक हैं अब्दुल भाई

[@AbdulKurad]

Thanks sir 🇮🇳👍😁

[@rustammohammed8255]

Abdul bhai ye pular mere liye bhi bejo

[@jagdishdodiya94]

1035 di ka Hayrolic on off valve lagana he kese lagte wo vidio.....he to bhejo...

[@AbdulKurad]

Sir kabhi job ayato banaunga OK sir thanks 🇮🇳👍

[@lekhusahu1839]

भाई साहब नमस्कार, क्या आप छत्तीसगढ़ वालों को सर्विस दे सकते हो क्या। मुझे अपने ट्रेक्टर पे काम करवाना है।ईंजन, हाइड्रोलिक,स्टेरिंग पे। कृपया बताएं धन्यवाद 🙏🙏🙏

[@AbdulKurad]

नही सर जी धन्यवाद आपका 🇮🇳👍🤝😊

[@rajeshkumargarhwal6993]

Hydraulic lever ki bahar se setting kaise Hoti hai bahar se bataen

[@AbdulKurad]

Sir ji jab andr se hi kaplit hojata hai usko fir bahar se karne ki jarurat nahi hoti ok sir ji thanks 🇮🇳👍

[@MohanLal-qo4wg]

Sir apse ek question hai ki left ki setting se pahale pc and dc livar ki position keya honi chahiye

[@prajapatichandu4008]

Sir mere pas swraj 735 fe 1998 modal ka he isme hidrolik ka red vale che kaltivetr uthta ni he or bleak che 5 inch hi uthta he or chalu me thi dire dire utar jata he sir to hidrolik me kya vajja hogi sir ??

[@neerajtractor5463]

Aap fany Hu

[@AbdulKurad]

Thanks you sir ji 🇮🇳😊👍💖

[@mayurchavhan6302]

4wd kaise banaya vdo mai batay Massey Fargoson

[@jitendrajitendrarajput2221]

अब्दुल भाई ऐसी सेटिंग महिंद्र ट्रैक्टर में हो सकती है क्या स्पेशल टोल से जरूर बताएं

[@youniskhanbaloch4325]

Isky agy jo special tool laga kr adjustment krty hyn uski humy measurement lenght or weight to batyn ap ka shukria hoga jnb.😊😊

[@skd5432]

Setting Lever Springs For MF35 Hydraulics
Making the settings on the lever springs for the Massey Ferguson 35 hydraulic system is quite a fiddly job, and the method is shown in detail with a written description of the process may also help.
The spring balance should be attached at the very end of the levers So here it is...
• Loosen retainer nut and eccentric cam. 

• Make sure quadrant levers are set at their sector 
marks. The round lever exactly over where it says ‘FAST’, the square lever next to where it says ‘DRAFT’ between the two dots and exactly where the arrow is. 

• Make sure the lift arms are in the fully lowered position. (that is upwards if the top cover is flipped upside down). 

     
• Make sure your spring balance is connected right at the top of the lever (if it is connected lower down the lever it will require more force to move the lever).
• When 3 lb. of pressure is applied it should only just spring it into contact with the front of the slot in the lever support bracket.
• Obviously adjustment of the spring pressure is made with the self-locking nut on the guide rods.
After this adjustment is made the eccentric cam can be moved around into firm contact with the cam arm and the nut
tightened. The above adjustments can be checked - move the operational lever from its sector marks into the response range, as the lever leaves the ‘FAST’ position the levers that we set with the spring balance should begin to move to the rear of the guides.
The adjustment is very fine and fiddly. It is often right at the end of the movement of the levers where the 3 lb. can be achieved.
The setting is 3 lb. (1361 grams) of force to move the lever. The reason for this is that this equals the force applied by the control valve spring when the assembly is fitted and connected in the tractor. It is a very difficult setting to make and when using a spring balance the 3 lb. setting cannot ever be particularly accurate. Another method would be to attach a piece of string to the lever and pass this over a roller with a 3lb weight hanging off the bottom of the piece of string.

[@farooqueshaikh3934]

7250.taktar.hydulk.satigka.viduo

[@AbdulKurad]

Ok sir ji kabhi uska job aayega to banaunga ok sir ji thanks 🇮🇳👍🤝😊

[@annappaannappa5041]

Sir help karnataka hydraulic setting problem please instrument

[@harjeetgaggi2834]

Harjeet Singh 👊👊👊👍

[@AbdulKurad]

Thanks you sir ji 🇮🇳👍😊

[@smartt2188]

सर जी मेरे पास मैंसी का 9500E 50hp ट्रैक्टर हैं जिसकी लिफ्ट ऊपर करने पर स्लो उठती है इसका क्या सॉल्यूशन हो सकता है सर नवा ट्रैक्टर है

[@smartt2188]

Please sir reply

[@anilgurjar1385]

अबदुल भाई ईद मुबारक भाई ये पोजिसनलिवर व कनटरोल लिवर बिच मे रखते है कया

[@user-dv6hw4lp6s]

मेस्सी ट्रेक्टर 1035 आयल ब्रेक में हाइड्रोलिक आयल कौन सा डाले बताये सर जी

[@sureshmandavi3990]

सर जी मेरे पास 1035 40hp आइल बेंंक्र है तो आइल कौन सा डालु

[@AbdulKurad]

Sir Ji Usme OIB Oil Dalta Hai Ok Sir Ji Thanks 🇮🇳👍🤝😊

[@heeraram2518]

Sir humeko Engine, lift , clach peti eska ketne. Rupay lagige PL sir aap batna

[@sachinchoudhrary9172]

Ustad ji Mere Paas tafi 30 hi main uska pump karaya hai uski Puli par do Nishan hai kaun se Nishant par drop setting karni hai

[@vinodrai8768]

Sir lift upar karne par khad khad ki aawaz aati hai kya kharab ho sakata hai

[@AbdulKurad]

सर जी आपका ट्रैक्टर कोनसा है बताना ओके सर जी धन्यवाद 🇮🇳👍

[@pradipsurjuse8038]

Sir ji pozisan livar set krte samy position livar ki position down rahni chaiye kya aur draft livar ki BHI position batya sir ji

[@AbdulKurad]

Sir fir video me aapne kya dekha saaf bataya huva he dekhlo ok sir thanks 🇮🇳👍

[@manojpanwar4603]

Sir hamare Massey 245 97 model hai
Heat hota hai acid daalkar saaf kar sakte hay

[@matudiyarajesh3521]

કલેગ રીપેરીંગ

[@djnileshngtechnical1898]

Abdul Bhai hamare massy. 1035 tractor khet me chalate chalate hydrolic apne app khud uper ho jati hai kya samsya ho Sakti hai

[@harpreet2683]

slow fast roller mein kitni fiiler gaze set karni hai sir ji.

[@user-dv6hw4lp6s]

मेस्सी ट्रेक्टर 1035 डी आई आयल ब्रेक वाला में हाइड्रोलिक आयल कौन सा वाला डाले सर जी

[@mdhridoymolla6488]

brother massey ferguson 7250 hydraulic filter change video upload karo

[@devilalprajapat4366]

Hello abdul bhai

[@AbdulKurad]

Thanks you sir ji 🇮🇳👍

[@devayanideshmukh2998]

पट्टी और रोलर मे कितना थाउजंट अंतररखना है.

[@skserfuddin2185]

Bhai jaan asehi ander se ekjest ka koi beja batao

[@vinoddobariya1136]

Sarji pranam,messey 1035di me hydrolic ka liver setting and auto draft ka kam karavya lekin empliment ko control se niche rakhine se tractor age puche chalta he please iska solution batana dhanyvad

[@Mrsainisahab007]

Escort 340 se Sar Maine Uske lift ka kam bhi karaya per kam uska Sahi Nahin hua vah clach per down ho rahi hai aur band Karte Teji se down Hoti Hai Is per main kya kar sakta hun

[@rohitkurhe9509]

Nice sir swaraj ka drop settings ka video dalo

[@AbdulKurad]

OK sir thanks 👍

[@rohitkurhe9509]

Aya ki Nahi job swaraj ka

[@rohitkurhe9509]

Okkkk thanks

[@rohitkurhe9509]

Sir swaraj ka Engine ka video

[@aniljat8897]

Liver stand genad ka bjan ky h k ha mil ta h

[@harpreet2683]

sir dono lever mein kitni gaze rakhni hai....

[@kennethmanyere1705]

Please do it in English as well

[@AbdulKurad]

Sorry Sir I'm not English Only Hindi Ok Sir Thanks 🇮🇳👍🤝😊

[@ravindraraikwar211]

Sir Mahindra 265di ki hydrolic setting spesal tool se ki jati hai sir hamare tractor ki hydrolic over hokar phas jati hai

[@s.k.b8838]

Sir yah liver setting karne keliye kitne nomber Ki Patti Use Karte Ho aap

[@sanketkhillare5359]

Sir kisi bhi tractor ki hydraulic dheere se niche jane ke liye kaun si setting hoti hai

[@jasrajdaiya881]

अब्दुल भाईआप आप का लीपट का वीडीयो बोहत अचा लगा सुकरीयि जसराज राजनीति

[@AbdulKurad]

Thanks you sir ji 🇮🇳👍😊

[@manoharnekkanti851]

Sir how much weight you hanging on livers to adjust spring

[@AbdulKurad]

Sir ji aapne video me kya suna mene bataya huva he ok sir ji thanks you 🇮🇳👍😊

[@skd5432]

Setting Lever Springs For MF35 Hydraulics
Making the settings on the lever springs for the Massey Ferguson 35 hydraulic system is quite a fiddly job, and the method is shown in detail with a written description of the process may also help.
The spring balance should be attached at the very end of the levers So here it is...
• Loosen retainer nut and eccentric cam. 

• Make sure quadrant levers are set at their sector 
marks. The round lever exactly over where it says ‘FAST’, the square lever next to where it says ‘DRAFT’ between the two dots and exactly where the arrow is. 

• Make sure the lift arms are in the fully lowered position. (that is upwards if the top cover is flipped upside down). 

     
• Make sure your spring balance is connected right at the top of the lever (if it is connected lower down the lever it will require more force to move the lever).
• When 3 lb. of pressure is applied it should only just spring it into contact with the front of the slot in the lever support bracket.
• Obviously adjustment of the spring pressure is made with the self-locking nut on the guide rods.
After this adjustment is made the eccentric cam can be moved around into firm contact with the cam arm and the nut
tightened. The above adjustments can be checked - move the operational lever from its sector marks into the response range, as the lever leaves the ‘FAST’ position the levers that we set with the spring balance should begin to move to the rear of the guides.
The adjustment is very fine and fiddly. It is often right at the end of the movement of the levers where the 3 lb. can be achieved.
The setting is 3 lb. (1361 grams) of force to move the lever. The reason for this is that this equals the force applied by the control valve spring when the assembly is fitted and connected in the tractor. It is a very difficult setting to make and when using a spring balance the 3 lb. setting cannot ever be particularly accurate. Another method would be to attach a piece of string to the lever and pass this over a roller with a 3lb weight hanging off the bottom of the piece of string.

[@akashkhadsan9349]

Sir mere pas masssey ka 6028 mini tractor he, sir iss tractorki hyatrolick kaise set kare

[@rohitkurhe9509]

Sir swaraj ka haydrolik trelar garam hone pe. Upar Nahi uthata

[@saurabhlodhi345]

गजब भाई गजब अब्दुल भाई कैसे हो नरेश सर जी कैसे हैं

[@AbdulKurad]

सौरभ सर हम थीक है और उस्ताद भी मजे मे है आप सुना ओ आप कैसे हो धन्यवाद सर आपका 🇮🇳👍

[@k.hparmar8410]

ટ્રાન્સફર વાલ્વ ( લોક)નવા મોડલ નો ફીટીગ કરી દીયો અબ્દુલ ભાઈ.👍👌

[@AbdulKurad]

Ha sir ye bhi thik he thore Dino baad oil likej karta he ok sir thanks 😁

[@rathvaashvin3303]

🇮🇳🇮🇳🇮🇳👆👆👌👌👍👍

[@AbdulKurad]

Thanks you sir ji 🇮🇳👍😊

[@puspendarsingh3511]

Abdul Bhai hamara message hai to 7250 hai uski awaaz bahut bhad bhad hoti hai Ham Kya Karen or kam power deta hai 48 hp hone kai bad bhi esa lgta ki 35 hp ka tractor chala rahe hain

[@AbdulKurad]

Sir Ji Uski To Bhut Si Vajah Hoti Hai Ye Sab To Dekhne Ke Baad Hi Pata Chalega Ki Aapke Tractor Me Kya Dikkat Hai Ok Sir Ji Thanks 🇮🇳👍🤝😊

[@sonugurjar0311]

साहब मेरे पास massey 245 है 2015मॉडल और ट्राली मे बहुत कम जोर करता है क्या क्लच की दिक्कत है या कुछ और दिक्क़त है बताये

[@AbdulKurad]

हा ऐसा भी हो सकता है चैक कर वा लो जोभी होगा पता चलेगा ओके सर जी धन्यवाद आपका 🇮🇳👍🤝😊

[@sonugurjar0311]

@@AbdulKurad बहुत बहुत धन्यवाद जी 🙏🙏