Important Part of Pipefitter Before and During Interview | How To Find Take Off?
Vložit
- čas přidán 21. 08. 2024
- Piping,Welding,Non Destructive Examination-NDT
Common Piping Angles and their Solutions,Known and Unknown Angles and Angle Chart,Solving Rolling Offsets,mitered Pipe Cuts,Multipiece Mitered turns, "Y" Layout,90 deg. Saddle on (tees) Standard Weight Pipe,Pipe Circumference Divided into Equal Parts,90 deg.on (tees) extra Strong Pipe,90 deg. Eccentric Pipe Intersections, 45 deg. laterals,Concentric and Eccentric Supports on 90 deg. Long Radius Elbow,3 Types,Angle between Bolt Holes of Flanges, Pipe template layout,orange Peel head layout,Concentric Reducer Layout,Eccentric Reducer Layout,laying out Bolt Holes in Flanges,laying Out Ordinate Lines and lengths,Tank coil layout,Angle Iron Miter Cuts and Brackets,Special Offsets and Solutions,Slip or Spectacle Blind Data,Centers of Eccentric reducers and Eccentric Flanges,Centers of 15 deg.,221/2,30 & 60 deg. Butt Weld Elbows from 90 deg. Long Radius Elbows,Pipe Thread,Dimension of Weldolet on Pipe, Dimension of Socket Weld & Screwed Fittings, Dimension of Flanges Cast Steel Valves,Dimension of Flanges Cast Steel Fittings,Commercial Pipe Sizes & Welding Fittings,General Dimension of Welding Fittings,General Dimension of Forged Steel Flanges,Bolt,Gasket & Ring Joint Number Charts,Wrench Sizes,Drill Sizes for Pipe Taps,& Tap Drill Size Charts,Bolt Charts for Orifice Type Flange,Outside & Inside Diameter of Pipe& Flange Bores,Comparison Chart for Packing & gasket materials,Hand Signal for boom Operated Equipment,Hand Signal for Overhead & gantry Cranes,Useful Information,Pipe Expansion,Pipe Bends,Circle,Inches&Feet Converted to millimeters,Conversion Constant,Decimal Equivalents,Fractions& millimeters,Safe Loads,for Wire and Manila Rope Charts,Decimal of a Foot,minutes converted to Decimals of a Degree and trigonometric formulas,Pipe& Water Weight Per Line Foot &Feet head of Water to PSI,Wire bending,Symbols,Computation.
Playlist:
Pipefitter Works • PipeFitter - Piping Works
How to Read Isometric Drawing? • How To Reading Isometr...
Angle Computation? • Pipefitter Angle Compu...
Welding Works? • Welding
Pipe,Welding,Non Desructive Examination-NDT • Pipe,Welding,Non Desru...
I love this teaching and want to learn more. Thanks Dear❤
❤nice idol
I think you miss to calculate (+-) like 252.6 to 253#. Sorry if im wrong.thanks for the formula
''4:53 '' 16 inches 45 deg. elbow center is 254 mm,( 5/8 x 25.4 = 15.875 mm x 16= 254mm) thats why 8440-254= 8186 it is not about the weld gap. Thanks for sharing
you are right nihat not the weld gap..the author used the 15.8 only ( lacking .075)
Yes this is the rigth computation.
Take off 45 degrees L/R
T.O. = O.D. of elbow x 0.625 inch.
Take off 90 degrees L/R
T.O. = O.D. of elbow x 1.5 inches
Thanks sir"
Thank you for the lesson.
My pleasure!
no explanations of what u r referring to... incomplete information just doesnt make sense
16, 15.8 etc what are those dimensions specifically referring to?
what is 670 verticle lines ?
why dont you do the take offs in inches
Good evening.
Trabaho ba talaga ng Pipefitter ang
mga ganitong calculation or trabaho ng Craftsman?
Apat na taon akong naging pipefitter
construction and maintenance ni hindi ko naranasan sa trabaho yang calculation na yan.
please correct it. what your idea share it
what software is used to draw these drawings ?
Boss spool na, d ky sfool
5\8-15. 8 meant what nd where did com from plz reply me
That have converted into mm
Hlo sir , could you send some pipe issomatric drawing pdf plz....
sir ano un 670 p? bat nandyan..
USING 15.8 IS WRONG YOU BETTER USE .625, OR 15.875 TO GET THE EXACT MEASUREMENT.
Nice video but I need full lecture.
If you have any pipeline drawing in PDF format please can you send me for study on my email id
Pa apply boss f hiring kayo baguhan pala po
Saan po nakuha ang 5/8?
i think yan po ang standard given na value ng formula paiba iba din po yan depende kung 45 ba or 90 degrees long or short radius 5/8 in fraction, 0.625 in inches, 15.875 in mm
Boss 16x15.8 na boss,wag mong baliktarin ang given numbers.
please correct it. what your idea share it
Boss hindi yn gaf, kon d gap yn boss
please correct it. what your idea share it