Diesel Two-Stroke VARIABLE COMPRESSION | Engine Rebuild
Vložit
- čas přidán 7. 02. 2024
- The Lohmann Diesel
I attempt to rebuild the small diesel engine in this video
#dieselengine #twostroke #moped
Seaside Garage is sponsored by SKIL
www.skileurope.com
If you want to support me and the projects head to my Patreon here:
Patreon: / seasidegarage
If you want to contact me then head to my Instagram here:
Instagram: / seasidegarageyt - Krátké a kreslené filmy
Well, when it comes to some rebuilds, you know what they say; "We do it right cos we do it twice!!!" :P
Hope once is enough!
@@SeasideGarage That is the hope, it's just having to take things apart to re-replace things, which I've done myself more times than I can remember, that's the "we do it twice" part... :P
@@twocvbloke haha ah yes ! :)
Don't forget to add a small amount of either to your diesel 2 stroke mix
You might have been able to get the "Oilite" bushes from Bearingboys in the UK.
Split type spring washers have been unacceptable for a long time now. They are banned on military aircraft. Use Nylocs unless it just has to look vintage. Serrated washers and Loctite as an alternative.
as I've experienced, split washers aren't accepted in general in any actual new engineering, the only reason they'd be used is because someone decided to simply copy&paste old stuff
Mate, it's time to use the press haha. Thanks for the interesting content!
Haha... it reminded me of the old days with no tools :D
I knew an old guy in Rågeleje, who had one. He told that when he once had the piston rings replaced, they had to pull it several km after a car, before the compression became good enough for it to start.
Urgh! Something must have been wrong then! :O
Damn. Left us with a cliffhanger
8:37 I removed a similar race by cutting a deep groove into it with a tungsten bur and cracking it
I have my fingers crossed that it's going to work. Cool little engine.
when you weld a bearing race to make it contract, you just keep welding, long pass not just spots, and it will get lose.
7:30 if you weld the bearing ring, you could have welded a bar across the ring and pull on that. Or even two hex nuts and just use two screws to push :D
Good idea!
hate to say now - but always put grease on crank oil seals like that - they have a wee groove for it.
I use assembly oil on the sealing surfaces :)
Remarkable engine, can't wait to see it run!
If there were Oscars awarded for tiny cuteness on a big scale 😁 that little sweetie would WIN 🏆, Seppo not you lol 😂 the ENGINE !!!!!! 😉
:D
this little guy is so simple! Although I still do not fully understand the design of the "carburetor". What does "desiccant" mean? Maybe a problem with the translation... Where can I find his scheme?
Its a dripper :)
if you had puts the welds further away from the ally casing side you could of got the puller under the welds to pull
Riktigt fascinerande liten motor, jag älskar små motorer och det var riktigt kul att se den invändigt. Lycka till med provstarten senare, vi är nog många som är nyfikna.
Dremil for getting the ring out😊
You should weld all around the bearing race, would probably work better... you could also put a piece of mild steel across with a nut in the middle and use a puller :)
Exactly my thoughts.
Yeah that works great, usually it just falls right out, in fact I don't recall it ever not working.@@krtgiroto
Did you measured the clearance between the faces of the piston ring?
I did not, its supposed to be pre gapped and I hope it is.. the cylinder is a blind hole so measuring is very difficult.. and my cylinder gauge is not small enough ! haha
It LOOKED good enough, at least not to small which would be catastrophic
Why do you need special tools to machine oil-impregnated bronze bushings?
Another video. Nice😮
I've been looking forward to this video, thanks
If it doesn't work it'll make a nice wall ornament. 😆
Interesting thanks
Why didn’t the Swedish supplier not want to send stuff to Denmark? Another fascinating video.
odds are it's due to customs and customs duties and fees
@@BraveSteelDragonthey can just vat tax it as normal, theres no customs. Its same "internal market. Just put it in the post and it goes over the bridge to denmark.
More likely its just a new situation to do sales to another country and they didn't want to think about it or all their stuff is payment on delivery that they don't have working between the border.
Dont know why, they just did not accepts addresses outside sweden and although houses are cheap over there, it was to much of a hassle... :P
Such a cute little engine! Good job and hope it produces more power than smoke!
It wil for sure smoke alot 😂😂✌️✌️
Bliver spændende og hører den i gang 🤩🤩🤟
Det blir spændende om den KAN høres igang! haha
@@SeasideGarage jeg håber på det bedste 😎👌
Vad är det här för motor? Fabrikat?
Vad har den använts till?
Jag har aldrig hört talas om en så liten dieselmotor!
Lohmann Diesel. der er flere videoer på min kanal om denne type motor. :)
Where can I buy one? I would like to make a mold and possibly bring this to mass market, in USA I believe these would sell
pretty impossible to find them...
Venter spændt på en opstarts video ..😀
will you do more video's about these?
Yes!! Its been awhile since something broke and parts are hard to find... But more will come soon.
@@SeasideGarage what parts do you need I might be able to help
@@robot797 I needed a new piston... But I got one made now ! But thanks !
@@SeasideGarage what type
I can get the 2 ring version within 3 days
@@robot797 that's was quick! But it arrived this week... :) to rings to control them all... :p
Fanme en fed motor 😎😎 er den dansk ? Sjældent at se 2takt diesel knallert
Hej jeg har mistet dine kontakt oplysninger angående loman diesel knallert
Prøv seppowashuus@gmail.com
difficult to watch that get destroyed