Mr. Sawdust shows off the Flying Wing jig, a surefire way to get perfect miters with the radial arm saw every time. Special thanks to Robert Ender for the intro music!
One day I went shopping on OfferUp and found a guy selling a 1953, DeWalt 3 phase, 3 horse GR54. I couldn’t believe my eyes. The thing looked brand new. Original paint, fully equipped and the former owner had even rigged an inverter so it could run on 220 single phase. He only asked $500. I went up to see it and verify that the thing really ran. It was perfect. No rust, not a single chip in the paint, threw a 14” blade and ran true and straight. It was even rigged with a switched power cord to operate a dust collector. I will never see a better deal for a power tool in my entire life. Trailered it home and spent the next week dialing it in to perfection. Added a custom made fence to hold Board Buddies for ripping. But I gotta say, Nothing but nothing beats a well made, 500 pound DeWalt radial.
Love this. I just finished my first reading of the Mr. Sawdust book. I have an OK Craftsman that I have finally managed to get into alignment after following a combination of Mr Sawdust, the factory manual, Jon Eakes book and the Delphi forum for DeWalt Radial arm saws. I was determined to get the Craftsman saw functional to finish up some very basic work I am doing right now. My dad built cabinets for my entire childhood on a DeWalt RAS, and I have recently acquired one, but it's apart for reconditioning at the moment. The Mr Sawdust book has a nice description of using a perpendicular fence with a 45 degree. I would guess the wing idea came about as your dad thought about how he could do the cuts even better!
Hi Wally. THANKS for sharing this! I have a 1959 MBF-251 that I have had for over 30 years. I recently retired and finally have time follow my wood working dreams. I look forward to getting the plans for this awesome jig and building one for my RAS. 👍👍👍😎
I use a jig similar to yours on my table saw. It work the same way as yours. I have made many jewlry boxes and the like using the jig and as you said ,"you can't get it wrong"! I like the fact that any length can be obtained. I have a friend that trims out buildings he also uses a table saw . you can also adjust the jig to get different angles. Your dad make an excellent picture frame.
Great video, I've watched it a few times. I have for years wanted a good radial arm saw, I've had 2 craftsmanship and both of them were good cutoff saws and that's about it. I believe now that I would like to get a 9inch mbf dewalt since they aren't to large. Thanks for the video and information
Hello Wally, I’ve been away from wood the last year, and happily just discovered this wonderful video. Thank You for sharing this gem, and I look forward to catching up on your other teachings! I’ve subscribed. Be well, stay safe, Best Regards, Shawn
Thank you all for the nice comments. I have to wonder about the 3 dislikes this video has gotten. Why no commentary to go along with the thumbs down ? I would appreciate knowing what you didn't like. Was it my video ? The jig ? The radial arm saw in general ? Or me ? Hitting dislike without a comment is like a hit and run. Thanks.
You can't focus on the dislikes. People dislike videos for the dumbest and most insignificant reasons. Focus on the 180 likes and all the positive comments below.
Sometimes when viewing videos on a cell phone a slip of the finger can press the thumbs down button . That could be a possibility. But like others have said . Don't worry about it . Video was very informative.
Hello, it,s a usefull Jig for a armsaw. Thx for sharing! I have a DeWalt too and this saw will have a flying Jig soon. I saw that you can move the leeft side back. Is the other right one not neccesary for omving back? Much greetings from us in Holland 🌷🌷
I did the same thing. I managed to find an old cast iron armed craftsman since there were no old dewalts in my area. I'm now on round three of setting it up and getting it square and am getting really close. I've had to take parts of it apart and clean out years of old packed sawdust and dirt but it now seems to be locking in at a consistent position. I almost threw it out after I set it up the first time an it wouldn't hold a setting. I think what has to be remembered is that all of these are now old, most are neglected, and most need to be cleaned and adjusted. I may still turf mine if I can't get it perfect but since I only paid $50 for it, and the recall on them from Emerson is $50, I'm not out anything to try and get it right. The tl;dr of all of this is try and get it set up, go through the manual step by step and see if you can make it work for you. If not, on to something that will.
Sure takes the fun out of guessing!! Very nice video. I now have my Father's old Craftsman RAS. I love everything about that saw! How does one obtain a copy of the design? Thanks!
One day I went shopping on OfferUp and found a guy selling a 1953, DeWalt 3 phase, 3 horse GR54. I couldn’t believe my eyes. The thing looked brand new. Original paint, fully equipped and the former owner had even rigged an inverter so it could run on 220 single phase. He only asked $500. I went up to see it and verify that the thing really ran. It was perfect. No rust, not a single chip in the paint, threw a 14” blade and ran true and straight. It was even rigged with a switched power cord to operate a dust collector. I will never see a better deal for a power tool in my entire life. Trailered it home and spent the next week dialing it in to perfection. Added a custom made fence to hold Board Buddies for ripping. But I gotta say, Nothing but nothing beats a well made, 500 pound DeWalt radial.
Thank you Wally. We need this sort of explanation and high quality video to bring the RAS back into favor with woodworkers. Great job!
Thanks you so much. I plan on doing many more and hope you will keep following.
Thank You Mr Kunkel......this is wonderful.....cheers from Florida, Paul
Wow, great video Wally! Love that frame your dad made. Absolutely beautiful!!!
I am waiting for your brothers plans for your fathers Flying Wing Jig. I have some big plans for it when I get it built. Great show.
I sure need to make one of these.....Thanks you so much, Paul in Florida
Love this. I just finished my first reading of the Mr. Sawdust book.
I have an OK Craftsman that I have finally managed to get into alignment after following a combination of Mr Sawdust, the factory manual, Jon Eakes book and the Delphi forum for DeWalt Radial arm saws.
I was determined to get the Craftsman saw functional to finish up some very basic work I am doing right now.
My dad built cabinets for my entire childhood on a DeWalt RAS, and I have recently acquired one, but it's apart for reconditioning at the moment.
The Mr Sawdust book has a nice description of using a perpendicular fence with a 45 degree. I would guess the wing idea came about as your dad thought about how he could do the cuts even better!
Nice video. Love seeing radial arm saws.
Hi Wally, really great video! You have so much talent to share. Looking forward to the plans for this jig. Thanks!
Hi Wally. THANKS for sharing this! I have a 1959 MBF-251 that I have had for over 30 years. I recently retired and finally have time follow my wood working dreams. I look forward to getting the plans for this awesome jig and building one for my RAS. 👍👍👍😎
This is great Wally! Thank you for sharing. So excited to see classes scheduled again… See you soon!
I use a jig similar to yours on my table saw. It work the same way as yours. I have made many jewlry boxes and the like using the jig and as you said ,"you can't get it wrong"! I like the fact that any length can be obtained. I have a friend that trims out buildings he also uses a table saw . you can also adjust the jig to get different angles. Your dad make an excellent picture frame.
Great video, I've watched it a few times. I have for years wanted a good radial arm saw, I've had 2 craftsmanship and both of them were good cutoff saws and that's about it. I believe now that I would like to get a 9inch mbf dewalt since they aren't to large. Thanks for the video and information
Hello Wally,
I’ve been away from wood the last year, and happily just discovered this wonderful video. Thank You for sharing this gem, and I look forward to catching up on your other teachings! I’ve subscribed.
Be well, stay safe,
Best Regards,
Shawn
Very nice, and more versatile than the one I built for myself a long time ago. I also would be interested in a copy of the drawings.
Subscribed!
Thanks for this great video Wally. I'm looking forward to the plans to make this jig!
And you shall have them Tommy
Awesome video, Mr. Son of Sawdust! I am restoring the same saw you are using there.
Outstanding!! I need the plans!!
Great information thank you
Thank you for keeping this going, I have a craftsman RAS, however, I am looking for a Dewalt.
I love keeping it going. Join that forum ! It will help you find the DeWalt you are looking for.
Thank you all for the nice comments. I have to wonder about the 3 dislikes this video has gotten. Why no commentary to go along with the thumbs down ? I would appreciate knowing what you didn't like. Was it my video ? The jig ? The radial arm saw in general ? Or me ? Hitting dislike without a comment is like a hit and run. Thanks.
You can't focus on the dislikes. People dislike videos for the dumbest and most insignificant reasons. Focus on the 180 likes and all the positive comments below.
Forget about the 3 dislikes, today on 2021-06-13 you've reached 222 likes.
Greetings from Pretoria, South Africa.
Sometimes when viewing videos on a cell phone a slip of the finger can press the thumbs down button .
That could be a possibility.
But like others have said . Don't worry about it . Video was very informative.
Hello, it,s a usefull Jig for a armsaw. Thx for sharing! I have a DeWalt too and this saw will have a flying Jig soon. I saw that you can move the leeft side back. Is the other right one not neccesary for omving back? Much greetings from us in Holland 🌷🌷
I just bought a Craftsman radial arm saw now I am second guessing myself. I am new to Radial Arm saws, and just subscribed to your channel.
I did the same thing. I managed to find an old cast iron armed craftsman since there were no old dewalts in my area. I'm now on round three of setting it up and getting it square and am getting really close. I've had to take parts of it apart and clean out years of old packed sawdust and dirt but it now seems to be locking in at a consistent position. I almost threw it out after I set it up the first time an it wouldn't hold a setting. I think what has to be remembered is that all of these are now old, most are neglected, and most need to be cleaned and adjusted. I may still turf mine if I can't get it perfect but since I only paid $50 for it, and the recall on them from Emerson is $50, I'm not out anything to try and get it right.
The tl;dr of all of this is try and get it set up, go through the manual step by step and see if you can make it work for you. If not, on to something that will.
Sure takes the fun out of guessing!! Very nice video. I now have my Father's old Craftsman RAS. I love everything about that saw! How does one obtain a copy of the design?
Thanks!
Is there a place I can view/buy the plans for the Flying Wing jig? I placed my order for the book today.
Where can one get a copy of his book?
www.mrsawdust.com
His book is unavailable
Do you sell copies?
Great info. Is that a Dewalt 1030?
I believe it is a 1030RA
@@ryderholywonder5864 Didn't look as green as a GWI, but could be. 1030 RA's are gray I think, mine is.
Great video and jig Wally! Here is the URL to the RAS Forum; forums.delphiforums.com/woodbutcher