Just found your channel. Amazing content! Thank you. Can you make a video on mold maintenance and servicing? And also on how to keep track of the mold changes and inventory?
What is the correct term for a key that switches which cavity in the mold you want to fill? I find the shop I work at kind of makes up terms on the fly and I’m looking to change that for ease of communication. Love the channel
The correct term is (Switchover or Transfer position) this is also called 1st stage to 2nd stage on older machines. The way is you fill the part to 95% to 98% in 1st stage the transfer to hold after you get to 95% or 98%. I hope this is what you were asking & I hope this helps you out. Thanks for watching & the support to the channel I greatly appreciate it.
Helpful video, thanks. Did you speak about in/out cylinder, how about the cooling of the cylinder. What do you mean(hold), is it maintien en french. Thanks again.
Hi,, thank you very much for your videos I have one doubt where we are using valve type and for which type components we are using sprue type gates in hot runner system?
It deepens on if it a sequenced valve gate. Most valve gates open at start of injection. If you have a big part, you are filling. You open the gate & watching where the flow is. 1st gate must past the next gate before opening that valve gate to the next one. If you want, I think I made a video over it. Thanks for watching & the support.
@@tuhoctiengnhatvaanhchuyenn1727 The best way to get a starting point for the settings would be through simulation. You would need to match your flow rate between the simulation and the press, but also remember the analysis software assumes your press and material are perfect and in real life it won't be. Calculating it by hand would not be worth the time since material flows radially so if the width of your part is changing the speed would also be changing.
@@injectionmoldingskillsmore1064 you integrate hrs into your current system. Just remove the hydraulic driven valve gate body and install their knuckle onto your pin mount the motor now your integrated... I don't understand what else you could mean by integrated challenging with respect!
@@joehart103 Sorry if I confuse you, We are buying new presses that have the valve gates intergraded in to the press PLC. We have a lot of older presses from 1954 & up. So we use portable units to control the valve gates. This is what I was trying to relay to you sorry if I miss understood you.
Thank you Dave. Your help is appreciated
Anytime if I can help & Thanks for watching & the support to the channel, I greatly appreciate it.
Thank you for the lesson
My pleasure! Thanks for watching & the support to the channel I greatly appreciate it.
Thanks, educated me, I encounted a case need valve gate.
Thanks for watching & the support to the channel I greatly appreciate it.
I like your videos and very informative content sir. Subscriber here from Philippines.
Thanks for the support, If you have any ideas that you would like to see please let me know. Thanks again for the support
thanks for the video
Thanks for watching
Just found your channel. Amazing content! Thank you. Can you make a video on mold maintenance and servicing? And also on how to keep track of the mold changes and inventory?
I will try in the next couple of weeks, thanks for watching & supporting the channel.
Excellent 👌
Thanks for watching & the support to the channel greatly appericated.
What is the correct term for a key that switches which cavity in the mold you want to fill? I find the shop I work at kind of makes up terms on the fly and I’m looking to change that for ease of communication. Love the channel
The correct term is (Switchover or Transfer position) this is also called 1st stage to 2nd stage on older machines. The way is you fill the part to 95% to 98% in 1st stage the transfer to hold after you get to 95% or 98%. I hope this is what you were asking & I hope this helps you out. Thanks for watching & the support to the channel I greatly appreciate it.
Helpful video, thanks.
Did you speak about in/out cylinder, how about the cooling of the cylinder.
What do you mean(hold), is it maintien en french.
Thanks again.
I think I did on one video, I will have to go & check to see. Thanks for watching the channel & the support.
What cause valve gate to get stuck open or close
Thanks for watching & the support to the channel I greatly appreciate it.
Hi,, thank you very much for your videos
I have one doubt where we are using valve type and for which type components we are using sprue type gates in hot runner system?
Not 100 % understand what you are asking sorry. Thanks for watching my videos & the support.
Can you guide me to set the correct opening and closing time of the valve pin? Calculator time setup open-close valve pin????
It deepens on if it a sequenced valve gate. Most valve gates open at start of injection. If you have a big part, you are filling. You open the gate & watching where the flow is. 1st gate must past the next gate before opening that valve gate to the next one. If you want, I think I made a video over it. Thanks for watching & the support.
@@injectionmoldingskillsmore1064 Do you have the formula to calculate the valve opening time or not?
If yes, please show me, thank you very much!
@@tuhoctiengnhatvaanhchuyenn1727 The best way to get a starting point for the settings would be through simulation. You would need to match your flow rate between the simulation and the press, but also remember the analysis software assumes your press and material are perfect and in real life it won't be. Calculating it by hand would not be worth the time since material flows radially so if the width of your part is changing the speed would also be changing.
Thx
Thanks for watching
If you want valve gate control you have to check out HRS servo driven valve gate systems.
We are trying to have everything integrated thanks for the offer.
@@injectionmoldingskillsmore1064 you integrate hrs into your current system.
Just remove the hydraulic driven valve gate body and install their knuckle onto your pin mount the motor now your integrated... I don't understand what else you could mean by integrated challenging with respect!
@@joehart103 Sorry if I confuse you, We are buying new presses that have the valve gates intergraded in to the press PLC. We have a lot of older presses from 1954 & up. So we use portable units to control the valve gates. This is what I was trying to relay to you sorry if I miss understood you.
The company i work for just got a hot runner mold. How can i determine if the mold has valve gates or a different type of gate?
The valve gates are hydraulic or pneumatic hook ups. If you don't have this then they are regular gates.
@@injectionmoldingskillsmore1064 Thank you, now that i think about it that seems quite obvious. sorry for the stupid question.
@@joshbowen2717 Its ok bud
I have ran ultem material. Has anyone ran peek material thru valve gate hot manifold.
Thanks for watching & the support to the channel greatly appreciated.