Thanks for the great video! Following your example, I just took mine apart, gave it a nice clean and polish, put it back together, and it is running!!!!
Nice work. It's good to see a man that is skilled with intricate details like a diesel injection pump. I'm sure that you will always have plenty of work to keep you busy, and keep the $$$ rolling in.
UH O,,, unscrewed the wrong one!!! Lol!!! Just kidding,,, thanks for the tear down vid,,, it’s people like y’all that take the time to make these videos help out a lot of do it yourselfers,
Hello friend, I have been watching your channel for some time and I can learn a lot from it. I have a Kubota B1400 tractor with a D850 engine and I have a question about how to set it up idle speed in this engine? The engine runs very slowly, and the revolutions fluctuate. When the engine is running, after opening the inspection cover in the pump casing, you can see that the spring and the rod that move the toothed rack, which is in the form of a cylinder, moves to the rhythm of the waving revolutions. When I move the rack with my finger and increase the revolutions, the engine works normally. when I let go, the revs drop and the engine cuts out. What is the cause of rpm fluctuating? the rack link should probably be stationary while the engine is running? On the opposite side of the pump's gear rack, there is a small cover screwed on with two screws, underneath which there are concealed locking pistons. There are three pivots, the central one which is stationary and two side ones which are mounted on the eccentric, can they be adjusted? what are these two side eccentric pins for? Do they regulate idle speed? I will be grateful for your response.
Did you have the tractor on TDC Since you TDC the injection pump. I heard it a pain. I have the same problem with my B7610. I have done my 4020 JD with roller master injector pump.
Thanks for showing how these are assembled!! I took mine apart and cleaned it but wasn’t sure how to time the gears. I’m still not 100% sure how to align the plungers ? Looks like they need to be aligned properly, what am I looking for to properly align ?
There's a timing mark between control sleeve and control rack and also in the plunger.if your plunger there is no timing mark, the cuts on the plunger must be place on your left side.
Hola , tengo un tractor con ese tipo de bomba, tira mucho humo a los 10 minutos de esta en marcha y olor a gasoil , creo que hay que adelantar un poco la bomba , podrias comentarme como se adelanta este tipo de bombas ? Gracias .
I found the video! I’ll watch it today and follow your steps!! Thank you so much for taking the time to show your rebuilds and repairs!! Where are you from?
@@tractorsmarinemechanic when I started my tractor after the pump rebuild I had a runaway diesel!!! It overheated and finally shut off! What did I do wrong? Can you put the plungers in the bottom backwards?
I forgot the model but the engines are Kubota D1402,D1302,D1100,DH1100,DM1100 and also for D650,D750,D850, D950.please also watch from my playlist other injection pump. thank you for watching and also please subscribe share and like.thank you.
Great video. Is a Westerbeke pump the same as the Kubota you showed us? I think my plungers are gummy after sitting for over 6 years. I think I'll let an expert rebuild my Westerbeke pump. Just in case.
Very nice work. Im having trouble getting the injection pump out . The shaft in the middle is stuck in the fullest out position and making it impossible to pull the injection pump upwards. Any ideas how to solve this?
Nice video thank yo so much, I have a question for you I found shims that goes under the rocker and have the inscription 375-370- and 365, do you thing where they goes respectively, I think 375 goes for piston 1, 370 goes for piston 3 and 365 for piston 2, regarding firing order on my tractor, the 375 is thicker than 370 its self thicker than 365, I think the thickness gives 1.2 degree between each injection time. thank you so much .best regard from Canada
I figured out that, the shims are for metering diesel fuel into the delivery valve, in order to pressurize the exact amount of fuel into the delivery valve, shims are not for timing. thanks have a good day.
I’m trying to rebuild the same pump but am in need of some control sleeves. Mine are stripped. Do you sell spare parts or where would you go to get control sleeves?
These videos are very helpful, thank you. I am about to rebuild a yanmar injection pump (John Deere part AM101403). What is the cleaning solution that you use?
Hi @tractors&marine MECHANIC, i have a Mitsubishi L3E engiene and the Fuel Injection Pump 094500 is very simular to this on your video ? I need the O- rings for the 3 fuel nossel i have one leaking after dismantle , do you know were i can get that ?
Hi, thanks for detailed video. I had the rack stuck a fews years ago and had to do that. The gen was a few years working with no major issues until now that get high rev all the times and I had not find the way to restore normal RPMs for work. When I started it go to full acceleration and I had to cut the fuel for turn off. Could be the rack governor loose in any way and stuck in high RPM? Any advice? Thanks. Is a Cummins onan 7500 with kubota 3 cylinder engine
I tried to disassemble and clean my pump quite similar to yours. When I test it without the lines connected (only diesel in-line), it only delivers diesel in two of three lines. What can be wrong?
It isn’t stuck… Is there a trick to test it without assembling to the engine? I was hoping to feel air pressure build up when I push on the rollers, but no…
There is no trick to test it just installed on the engine to test.are you sure you will set up all the timing marks on the plunger?remove all delivery valve holder also the delivery valve and you can see the plungers
@@tractorsmarinemechanic yes i removed all delivery valves and all plungers and cleaned. All the timing marks on the push rod is in the right place. If I operate the plunger by hand I can feel a little resistance from the air pressure that disappears if I push the rod in the stop-position, so that should be OK I think. Is it possible to have an air lock in only one of the plungers?
I have a 2cyl pump Can't get one of the assemblies to align and place the screw to lock in place, if I do, I can't open and close it jams...and the spring and roller stay jammed seems like everything is align and proper position any idea what I'm doing wrong?
@@tractorsmarinemechanic I got the pump back together seems to be working properly no luck starting the engine yet....need to check injectors next, its a mitsubishi KE75
@@tractorsmarinemechanic Your videos have helped alot finally got the engine to start seems like the blowby was keeping the engine from getting air or my injectors where not firing
Hello sir. Nag leleaking po injection pump ko. Tuma tagas ang grudo pumupumta sa engine oil ko. Ano po kaya problema ng injection pump ko sir . salamat sa sagot sir
Among unit mo sir?hndi kc parepareho Ang mga gear ng tractors.baka sira n gear mo sir kaya bumabalik n s neutral.pasubscribe nmn channel ko sir Salamat.
Those name are.plunger barrel,plunger or element pump,spring plunger,sleeve control,delivery valve spring,delivery valve gasket,delivery valve,rack control,control sleeve rack and also housing pump assy.Pls subscribe,share and hits like.thank you
Is there a vidio showing how you removed this..
Thanks for the great video! Following your example, I just took mine apart, gave it a nice clean and polish, put it back together, and it is running!!!!
Nice work. It's good to see a man that is skilled with intricate details like a diesel injection pump. I'm sure that you will always have plenty of work to keep you busy, and keep the $$$ rolling in.
Thank you for watching.pls subscribe,like and share.ty
UH O,,, unscrewed the wrong one!!! Lol!!! Just kidding,,, thanks for the tear down vid,,, it’s people like y’all that take the time to make these videos help out a lot of do it yourselfers,
Thank you for watching.
Sir ito din po Yong binaklas ng mikaniko Pero wala po cya pinabili sakin,sir may IBA pa po ba na dahilan para maghalo Yong diesel at langis sir
Hat mir geholfen meine Pumpe wieder richtig zusammen zu bauen. Vielen Dank.😀
Hello friend, I have been watching your channel for some time and I can learn a lot from it. I have a Kubota B1400 tractor with a D850 engine and I have a question about how to set it up idle speed in this engine? The engine runs very slowly, and the revolutions fluctuate. When the engine is running, after opening the inspection cover in the pump casing, you can see that the spring and the rod that move the toothed rack, which is in the form of a cylinder, moves to the rhythm of the waving revolutions. When I move the rack with my finger and increase the revolutions, the engine works normally. when I let go, the revs drop and the engine cuts out. What is the cause of rpm fluctuating? the rack link should probably be stationary while the engine is running? On the opposite side of the pump's gear rack, there is a small cover screwed on with two screws, underneath which there are concealed locking pistons. There are three pivots, the central one which is stationary and two side ones which are mounted on the eccentric, can they be adjusted? what are these two side eccentric pins for? Do they regulate idle speed? I will be grateful for your response.
Thanks malaking tulong yan boss .natapos ko yung ganyang project ko kanina
Salamat sa panonood sir.
Did you have the tractor on TDC Since you TDC the injection pump. I heard it a pain. I have the same problem with my B7610. I have done my 4020 JD with roller master injector pump.
Thank you. Thank you. Thank you!
Kindly like,share and also subscribe.thank you
Thanks for showing how these are assembled!! I took mine apart and cleaned it but wasn’t sure how to time the gears. I’m still not 100% sure how to align the plungers ? Looks like they need to be aligned properly, what am I looking for to properly align ?
There's a timing mark between control sleeve and control rack and also in the plunger.if your plunger there is no timing mark, the cuts on the plunger must be place on your left side.
@@tractorsmarinemechanic thank you!!! I’ll work on it tomorrow.
Hola , tengo un tractor con ese tipo de bomba, tira mucho humo a los 10 minutos de esta en marcha y olor a gasoil , creo que hay que adelantar un poco la bomba , podrias comentarme como se adelanta este tipo de bombas ? Gracias .
I found the video! I’ll watch it today and follow your steps!! Thank you so much for taking the time to show your rebuilds and repairs!! Where are you from?
Philippines.and also what country are in?
@@tractorsmarinemechanic United States
@@tractorsmarinemechanic when I started my tractor after the pump rebuild I had a runaway diesel!!! It overheated and finally shut off! What did I do wrong? Can you put the plungers in the bottom backwards?
@@tractorsmarinemechanic or can you put the delivery valve in backwards?
No
What is the model/part number for this pump so that I can source spare parts - excellent video - worked for me.
I forgot the model but the engines are Kubota D1402,D1302,D1100,DH1100,DM1100 and also for D650,D750,D850, D950.please also watch from my playlist other injection pump. thank you for watching and also please subscribe share and like.thank you.
What is in the pan that you keep dipping the parts in before you reinstall them??? Is it parts cleaner or diesel? Thanks. Very good video.
It's a diesel
Very thoughtful and very useful and very clear
Thank you for watching.pls share and subscribe
Hello. Would this cause excessive smoking?
Great video. Is a Westerbeke pump the same as the Kubota you showed us? I think my plungers are gummy after sitting for over 6 years. I think I'll let an expert rebuild my Westerbeke pump. Just in case.
I think you can do it
What an awesome video, amazing footage , keep it up brother
Thank you for watching.please subscribe like and share.thank you
Un GRAND Merci , thank you very much indeed , Muchas Gracias
Thank you also for watching.pls subscribe
Grazie x questo video, molto bravo complimenti, ciao
❤❤❤I love your videos
Great video. This is going to help me tremendously. Thank you!
Thank you too for watching.kindly share and subscribe
Very nice work. Im having trouble getting the injection pump out . The shaft in the middle is stuck in the fullest out position and making it impossible to pull the injection pump upwards. Any ideas how to solve this?
Please try to remove the delivery valve holder and also the delivery valve.
You're the best👍
Yup💪
Nice video thank yo so much, I have a question for you I found shims that goes under the rocker and have the inscription 375-370- and 365, do you thing where they goes respectively, I think 375 goes for piston 1, 370 goes for piston 3 and 365 for piston 2, regarding firing order on my tractor, the 375 is thicker than 370 its self thicker than 365, I think the thickness gives 1.2 degree between each injection time. thank you so much .best regard from Canada
I figured out that, the shims are for metering diesel fuel into the delivery valve, in order to pressurize the exact amount of fuel into the delivery valve, shims are not for timing. thanks have a good day.
gute Arbeit, vielen Dank
Good job !
Very very good thank you
Thank you for watching.pls Subscribe hits like and share.thank you.
I’m trying to rebuild the same pump but am in need of some control sleeves. Mine are stripped. Do you sell spare parts or where would you go to get control sleeves?
I do not selling spare parts.im sorry.
These videos are very helpful, thank you. I am about to rebuild a yanmar injection pump (John Deere part AM101403). What is the cleaning solution that you use?
It's a diesel only.thank you for watching my video.pls subscribe share also hits like.yanmar engine and kubota is almost the same of injection pump.
Great, thank you!
@@tractorsmarinemechanic don’t soak your hands like that in diesel, you will get sick from it. It’s not healthy.
Thank you
احسنت بارك الله فيك
Thank you for watching.pls subscribe
Hi @tractors&marine MECHANIC, i have a Mitsubishi L3E engiene and the
Fuel Injection Pump 094500 is very simular to this on your video ? I need the O- rings for the 3 fuel nossel i have one leaking after dismantle , do you know were i can get that ?
Go to the auto supply and can buy.thank you for watching
Please also subscribed share and like thanks
Hi, thanks for detailed video. I had the rack stuck a fews years ago and had to do that. The gen was a few years working with no major issues until now that get high rev all the times and I had not find the way to restore normal RPMs for work. When I started it go to full acceleration and I had to cut the fuel for turn off. Could be the rack governor loose in any way and stuck in high RPM? Any advice? Thanks. Is a Cummins onan 7500 with kubota 3 cylinder engine
rack stuck is the problem just fix it.thank you for watching kindly share, like and subscribe.
Hello sir. Same lng po ba ng injection pump sa lahat na na bangit sa engine ? From 1802 to 2601? Same lng injection pump nila sukat?
Preho lang po . sa plunger lock lang may pagkakaiba
@@tractorsmarinemechanic paps baka may alam ka ma bibilhan ng plunger d950 injection pump plunger. Need ko po kasi. Thank u.
Saan Lugar k sir?punta k ng metro Diesel
Impressive boss
Pump testing tool hi kya
I tried to disassemble and clean my pump quite similar to yours. When I test it without the lines connected (only diesel in-line), it only delivers diesel in two of three lines. What can be wrong?
Maybe the delivery valve is stuck.try to loosen the holder and check it.thanks for watching
It isn’t stuck… Is there a trick to test it without assembling to the engine? I was hoping to feel air pressure build up when I push on the rollers, but no…
There is no trick to test it just installed on the engine to test.are you sure you will set up all the timing marks on the plunger?remove all delivery valve holder also the delivery valve and you can see the plungers
@@tractorsmarinemechanic yes i removed all delivery valves and all plungers and cleaned. All the timing marks on the push rod is in the right place. If I operate the plunger by hand I can feel a little resistance from the air pressure that disappears if I push the rod in the stop-position, so that should be OK I think.
Is it possible to have an air lock in only one of the plungers?
what are you using a solvent / cleaner?
Diesel only
What are the two bolts on the back? The ones under the data plate.
It's a plunger guide
Thank you for watching kindly share and subscribe.thank you
@@tractorsmarinemechanic Thanks. It looks like it would allow you to adjust the orientation of those plungers
many Thanks for sharing
Thank you for watching.pls subscribe
I have a 2cyl pump Can't get one of the assemblies to align and place the screw to lock in place, if I do, I can't open and close it jams...and the spring and roller stay jammed seems like everything is align and proper position any idea what I'm doing wrong?
To re-assemble and to re align is very hard you need to be patient to align and place the screw tock in place.i know you can do it
@@tractorsmarinemechanic thanks where can I buy the copper washers?
You can buy at metro diesel Philippines
@@tractorsmarinemechanic I got the pump back together seems to be working properly no luck starting the engine yet....need to check injectors next, its a mitsubishi KE75
@@tractorsmarinemechanic Your videos have helped alot finally got the engine to start seems like the blowby was keeping the engine from getting air or my injectors where not firing
Where can new springs be purchased?
You can purchased from the metro diesel ( Philippines)
parehas ba cla ng plunger ng 3d84-1fa boss?
Iba po cguro sir.
Great video, but terrible background music or sounds !!
Salamat sa panonood.
The mic is picking up sounds in the shop.
Wow
Does this affect the timing when you do this?
Hello sir. Nag leleaking po injection pump ko. Tuma tagas ang grudo pumupumta sa engine oil ko. Ano po kaya problema ng injection pump ko sir . salamat sa sagot sir
Anong makina po?
D950 engine po. Pwedi pa po ba ma ayus ang injection pump ko sir. Lagi nlng na pupuno engine oil ko mg krudo. Ano po kaya pyesa papalitan sa luob sir?
Pwd p sir maayos.galing sa plunger Ang leaking.
Sir pwdi ko pa ayus sa iyo? Papadala ko thanks
Saan Lugar k po sir?kailangan po sa makina mo mismo itrouble natin.
Ano possible na sira sa PTO bumabalik kc Yong second gear sa nuetral
Among unit mo sir?hndi kc parepareho Ang mga gear ng tractors.baka sira n gear mo sir kaya bumabalik n s neutral.pasubscribe nmn channel ko sir
Salamat.
@@tractorsmarinemechanic L2602DT sir
Sir tanong kolang ung welding generator namin kubota D902 dilosyon diesel halo sa engine oil, san b tamang sira sa pump ba o sa feed pump tnx po
Dalawang bagay Yan sir.unang tingnan mo muna sa feed pump at Kung Hindi sa feed pump sa plunger galing.
leopard same 85 exp
How do you remove injector pump from engine
What are those parts inside pump called??i wana do a rebuild on mine.does it have to have 12v to work?
Those name are.plunger barrel,plunger or element pump,spring plunger,sleeve control,delivery valve spring,delivery valve gasket,delivery valve,rack control,control sleeve rack and also housing pump assy.Pls subscribe,share and hits like.thank you
Does it need 12 v?
@@tractorsmarinemechanic super cool
What is the 12v?
@@virgiliomireles1508 its a mechanical pump..dont need 12 volts to open a solenoid...but some kubota pumps do.
Hi, I need help fixing a Yanmar engine. Please help me. Do you have a phone number?