how to fix injection pump kubota D1105/D722

Sdílet
Vložit
  • čas přidán 26. 08. 2024

Komentáře • 118

  • @mikedx2706
    @mikedx2706 Před rokem +3

    Don't you all love how clean everything is when he reassembles the FI pump and metering jets?

  • @josephpuchel6497
    @josephpuchel6497 Před rokem +4

    Hey last but not least the culprit. Excellent breakdown video.

  • @rimantsbaranausks4422
    @rimantsbaranausks4422 Před 3 lety +4

    Your video made my life much better. I managed to fix my problem. Thanks a lot

  • @willdog3
    @willdog3 Před 2 lety +3

    Ive always been told these need to be taken apart in a sealed environment, like zero dust or grease. Obviously, that isnt the case lol. Good to see, these Kubota engines and their pumps are damn near indestructible.

  • @ALEJANDROReyes-cb9ce
    @ALEJANDROReyes-cb9ce Před 3 lety +2

    Thank you so much for your video May God bless you 🙏 for all your help

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 3 lety

      Thank you also for watching and if you learned something for it.pls.subscribe share and hits likes.

  • @kimidevil
    @kimidevil Před 3 lety +2

    I admit that I learned a lot from this video.
    Congratulations on the mastery and skills, but I don't like the messy workplace and the mixing of the elements of the pump sections. I wish to see a level up next time.

  • @Grupoproyectodozz
    @Grupoproyectodozz Před 9 měsíci +2

    Con que limpia las partes ? Con diésel?

  • @JoseMG54
    @JoseMG54 Před 2 lety +2

    the almighty god be with you,thank you for this video

  • @JoseMG54
    @JoseMG54 Před 2 lety +1

    Thakyou for doing this video it helps me to fixed my,again than you

  • @drfogg1
    @drfogg1 Před rokem +1

    they are smooth i had to use a wire wheel to clean all the parts they were stuck together really bad tarnis and rust i might of reined the pumps tolerances

  • @eborbore
    @eborbore Před 2 lety +1

    Great video thankyou. I've rebuilt my pump and each port shoots out fuel as expected but it doesn't appear to get enough pressure to pop the injectors. The injectors work find on another machine. Any ideas ?

  • @benjaminhenault6279
    @benjaminhenault6279 Před 2 lety +2

    Are you sure that the plunger should not be in the opposite side (M30 not facing the plunger rack)? If I follow you, the fuel delivery valve is not shutting off when the rack is at off position. Thanks

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 2 lety

      Different engines with different designed of injection pump.

    • @flightace1
      @flightace1 Před rokem

      @@tractorsmarinemechanic isnt this a 16032 pump? im pretty sure that benjamin is right,,no matter what engine this pump sits on it works the same,,this zexel/Bosch pump sits on many diffrent engines,not just kubota,,like kia cars and iveco for example.i realy whant to know if u put that plunger the wrong way cus im rebuilding one myself and all info i could find but yours say the other way around,,,M30 at the back(slots in the plunger on the backside were the hole is in the cylinder.)

  • @karim64shamal42
    @karim64shamal42 Před 3 lety +1

    بارك الله فيك عندي نفس المشكله

  • @kevin1gasman
    @kevin1gasman Před 2 lety +1

    I got D722-E Kabota the pump will bleed out of the bleeder valve not out of the injector . I tried running it last night . I’m hoping the fuel soak to the parts . Let it start working again. Motor be sitting for about 1 year . If not look like I’ll take to take it apart clean it . Thank for the video. ? What if I take the injector lines off . Try spraying cleaner or wd40 Will that help Will the loosen up the parts ? Before attempting . Taking it apart .

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 2 lety +1

      Thank you for watching.yes..try spraying cleaner or use WD-40 to help loosen up the parts.

  • @paulwoodburn1086
    @paulwoodburn1086 Před 2 lety +1

    Is there a rebuild kit / pn for these pumps? Even if it’s just for the seals? Thank you great video

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 2 lety

      I'm sorry I have no idea if there is a rebuild kit for this pump.thank you for watching kindly share and subscribe.thank you.

  • @jram7047
    @jram7047 Před rokem +1

    Nearly identical looking in my d1703 kubota engine, I've heard that you can upgrade components for more power in these but I don't know where to start . Do you know of any sources for power adders?

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před rokem +1

      I'm sorry I don't have an idea to upgrade. you can alter the plungers if you can add more power.thank you for watching.please subscribe.thank you

  • @summerstwin
    @summerstwin Před rokem +2

    Can you give more info on what kind/size O rings those are.

  • @edselniola3528
    @edselniola3528 Před 2 lety +1

    Galing nyo sir..
    Sir, nag DIY po aq ng injection pump ng kubota v1405, pagsalpak q nahwild na.. saan po kaya aq nagkamali sir?

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 2 lety +1

      Hndi mo naipasok ng maayos ung control ng injection pump.bunutin mo ulit.please subscribe,share hits like.salamat

    • @edselniola3528
      @edselniola3528 Před 2 lety +1

      @@tractorsmarinemechanic subscriber mo n po aq sir, matagal na po😎

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 2 lety

      Salamat sir.

    • @edselniola3528
      @edselniola3528 Před 2 lety

      @@tractorsmarinemechanic nalito kc aq sir sa dalawang kanal, may maliit at may maluwag😓

  • @philbertnestory670
    @philbertnestory670 Před 2 lety +1

    Thanks friend ihave got idear

  • @Noshopgarage
    @Noshopgarage Před rokem +1

    Will this fix it getting too much fuel? My Kubota is blowing white smoke that smells like raw fuel and I already replaced injectors

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před rokem

      Your problem is not in the injection pump itself.i think the piston ring or sleeve is the problem..

  • @petersamodhar9527
    @petersamodhar9527 Před 3 lety +2

    Please ,I am not argue with you, phasing May not be there.but calibration certainly is there, please see, ovel Shep grove is there,on the barrel holder.

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 3 lety +2

      Ok. The plunger barrel and the plunger there is a timing mark.if your plunger is already installed remove delivery valve HOLDER and also the DELIVERY VALVE .if you facing the control rack pump cuts from the plunger must be on the left side.just follow the timing mark at the control SLEEVE and PLUNGER.

  • @georgegautier372
    @georgegautier372 Před rokem

    Hi, thanks for detailed video. I have this engine in a onan cummin generator and When I started it go to full acceleration and I had to cut the fuel for turn off. Could be the rack governor loose in any way and stuck in high RPM? Any advice? Thanks.

  • @MrToluen60
    @MrToluen60 Před 3 lety +2

    Very interesting !

  • @jasonandjazmyncorley8800
    @jasonandjazmyncorley8800 Před 3 lety +2

    Could diesel mix with oil if this pump was bad? N84 engine

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 3 lety

      No..most of in this pump coming from the defective feed pump.some of injection pump coming from the plunger.

  • @ChooChooRooter
    @ChooChooRooter Před rokem +1

    Got a question My Kubota K 008 mini x is blowing smoke and I have case pressure If you take the dip stick out while the engine is running It will blow oil out Will this fix the issue???

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před rokem

      I think you need to overhauled your engine or replace piston ring or maybe resleeve

  • @keys72
    @keys72 Před 2 lety +1

    Hi, I gotta a question for you, friend. Those d1105 engines come in a turbo variant, is it an easy upgrade to take a 24 hp regular and turbo charge it to that sweet sweet 33 hp by any chance? What would I need to safely turbo it?

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 2 lety

      If you try to installed new turbo for your engine to add HP.im sorry never try to upgrade engine for an experimental.thank you for watching

  • @frankbaggett9290
    @frankbaggett9290 Před 5 měsíci +1

    If you put those fuel pins in with the slot on that side your engine will run away.

  • @gilbertobautistasalvador6016

    Calibración de punteroas

  • @alexanderperez8086
    @alexanderperez8086 Před 2 lety +1

    Pls arranges the parts in order posision sir for viewing

  • @kiendiep
    @kiendiep Před 2 lety +1

    Very good

  • @BiffsEquipment
    @BiffsEquipment Před 2 lety

    I have the exact same pump as you in this video only my fuel inlet and return line are on the opposite sides as your pump.. does this mean my plungers have to face the opposite direction as yours? Or do my plungers still go in the same direction as how you did yours? Any help would be greatly appreciated

    • @BiffsEquipment
      @BiffsEquipment Před 2 lety +1

      The problem I’m having is the fuel stop valve is not shutting the fuel off.. my rack moves smooth and so do the plungers. I have tried to flip the plungers 180 degrees and I still get fuel coming out of the pump and the stop valve still won’t shut the fuel off. Im stumped

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 2 lety +3

      Kindly remove again your pump.i think the small pin that guide into the plunger was lost

    • @BiffsEquipment
      @BiffsEquipment Před 2 lety +1

      @@tractorsmarinemechanic thanks for your reply, I figured it out, it wasn’t a lost pin but that was a good suggestion as they are easy to loose.. the issue was actually quite simple, I was using mechanics wire to tie over the shut off leaver to make sure it would cut the fuel off but didn’t realize that the stop leaver was not bottomed out against the adjustment bolt.. apparently the stop leaver will not work unless it’s fully touching against the threaded bolt that adjusts the leaver. So needless to say once I tightened the mechanics wire a bit more to hold the leaver more firmly over while I turned the engine over the fuel stopped coming out of the pump. All is good and I have the engine up and running again. Thanks so much for your videos!

  • @drfogg1
    @drfogg1 Před rokem +1

    hi thx for the video. however when i reinstalled the pump my motor runs at full speed i dont know what i did wrong it in an onan generator please help

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před rokem

      Check the control rack if hard to move just reassemble again.control rack must be smooth to move

  • @petersamodhar9527
    @petersamodhar9527 Před 3 lety +1

    Please explain how to Calibret the pump you assembled.(kubota).thank you.

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 3 lety

      This kind of pump we don't need to calibrate unlike to the injection pump of automotive engine.

  • @rimvydasiliukevicius1515

    Hello. How i can adjust for kubota li 215
    For more fuel?

  • @cs-gj3yf
    @cs-gj3yf Před 2 lety +1

    hey do you know the timestamps of when you showed the delivery valves, plungers and barrels?

  • @mikemurphy4591
    @mikemurphy4591 Před 3 lety +1

    I’m currently searching for the lower plunger springs and can’t find them anywhere. Any suggestions?

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 3 lety +1

      Thank you for watching.pls.subscribe to my channel.you can find that spring here in the philippines.what is the model of injection pump do you have?

    • @andik859
      @andik859 Před 3 lety +1

      Very interresting. I watch from Germany.

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 3 lety

      Thank you for watching.pls subscribe likes and share my video

  • @abrahamhorball1143
    @abrahamhorball1143 Před 2 lety +1

    Do I need to calibrate the pump after the clean and reassembling?? Please help me I’m trying to do this on my small kobuta g1900 4ws

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 2 lety

      Most of the Kubota injection pump no need to calibrate after rebuild unlike to the Isuzu engines.thank you for watching please share and subscribe.kindly also watch from my playlist or this one
      czcams.com/video/cO5qPn7S6co/video.html.thank you.

  • @BiffsEquipment
    @BiffsEquipment Před 2 lety +1

    Awesome video, I’m the kind of guy where If i can just watch the job being done once I’v got it down pat. I have a question, I bought larger plungers for my Kubota D902 engine, the guy who makes them claims it will give up to 5hp more with the right amount of air.. what is the difference of running larger plungers Vs. just turning the fuel screw? Basically I wanna know why someone would want larger plungers to get more fuel when they can just simply turn the fuel screw to allow for more rack travel.. I assume both methods allow for more fuel but they do it in different ways? Which way do you suggest is better if you want to add a little more fuel to the engine?
    Thanks so much!

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 2 lety

      I'm sorry I never try to replace larger plunger than the original.thank you for watching.

    • @BiffsEquipment
      @BiffsEquipment Před 2 lety

      @@tractorsmarinemechanic howcome? I assume you just keep things original which I understand, your not in the business of modifying pumps but I’m just curious to the affects

    • @duchuntr001
      @duchuntr001 Před 2 lety +1

      Larger plungers will increase fueling(volume) across the entire rpm range. The fueling screw only increases max fueling under load.

    • @BiffsEquipment
      @BiffsEquipment Před 2 lety

      @@duchuntr001 thanks so much buddy! Exactly what I wanted to know, I had a feeling that’s what it was but just wanted to be sure. I’ll prolly toss them in tom and see what happens

    • @duchuntr001
      @duchuntr001 Před 2 lety +1

      @@BiffsEquipment cool. With the increase in fuel you might want to look at adding a small turbo.

  • @dannyboy2382
    @dannyboy2382 Před 3 lety +1

    what are the symptoms when this pump goes bad?

  • @danjimielson
    @danjimielson Před 3 lety +1

    how much torque to tighten the top fittings

  • @dmc31405
    @dmc31405 Před 3 lety

    I have a Kubota L2350DT and it looks like i'm going to have to remove the pump and clean up the internals. I assume that the intake manifold will have to be removed in order to remove the pump from its housing. Is there anything I need to know in regards to the pump orientation with the forks on the throttle linkage. Or does the pump just simply lift out after I remove the fuel line and the associated mounting bolts.

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 3 lety +1

      Just remove intake manifold And bolts you can lift out that pump

    • @dmc31405
      @dmc31405 Před 3 lety +1

      @@tractorsmarinemechanic Thanks for your reply. Are the machined cuts on the plungers supposed to be oriented facing the rack? I think that in most videos that seems to be the case, but its hard to be certain. I did test my fuel flow just after re-installing the pump, and prior to connecting the the injector lines, and everything seemed good with the fuel control. I do seem to have a low speed miss, but that may be due to not having the idle stop properly adjusted yet. The skip goes away with a slight increase in RPMs. Your videos are very good by the way, I hope they are paying you well where you are working. Just a little more emphasis on the plunger orientation would be awesome. What is your fist name? Mine is Don. Thanks again for taking the time to post these videos. Maybe you could consider making some injector rebuild videos in the future.

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 3 lety +1

      The cuts on the plunger is facing on the rack and you were right.my next video I will do best I can to show you more clearly.

  • @espartacusitalia561
    @espartacusitalia561 Před 3 lety

    Hola saludos desde México, agradezco mucho la aportación de tus videos, sirven a muchos de nosotros, un favor podrías apoyar subiendo un vídeo de como calibrar las punterías del motor Kubota modelo CT3-44TV (D722) este motor lo traen equipos para refrigeración marca Carrier, agradezco de antemano tu atención y ojalá tengas una aplicación de transductor de idiomas, sigue con este buen trabajo tu servidor Sr. Cristalinas.

  • @danielboyd9507
    @danielboyd9507 Před 3 lety +2

    Is there any way to turn up this pump . Or how do you advance the timing. Not much information on this one. I have on on my kubota zero turn mower. Very informative. Thanks

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 3 lety +3

      If you want to advance...this kind of injection pump,you can turn the plunger barrel housing or plunger holder.move from left to right.thank you for watching

    • @danielboyd9507
      @danielboyd9507 Před 3 lety +1

      I will indeed keep watching. Thanks so much for the reply.

    • @alexbilenkin3418
      @alexbilenkin3418 Před 3 lety +2

      @@tractorsmarinemechanic just watched, liked and subscribed. Now about advance. You can do it by removing or replacing with tniner one gasket between pump and block. Moving holder gives more fuel. Correct me if I am wrong.

    • @tractorsmarinemechanic
      @tractorsmarinemechanic  Před 3 lety

      Correct

  • @joverila7492
    @joverila7492 Před 2 lety +1

    San po kayo Banda sir?

  • @rubengabayeron4221
    @rubengabayeron4221 Před 3 lety +1

    boss bakit shakey ang makina ko kubota D950. ok naman ang mounting anu kaya ang dahilan?

  • @michaelbirchall2247
    @michaelbirchall2247 Před rokem +1

    Surely that'll never work again?

  • @regdor8187
    @regdor8187 Před 2 lety +2

    Amateur......