$500 Yamaha YZ450 - Fixing ALL the PROBLEMS! *IT RIPS!*
Vložit
- čas přidán 24. 07. 2024
- Welcome back to another episode of the $500 2008 Yamaha YZ450F build!
In this video I:
Changed the oil and filter
Tightened the drive chain
Flushed and changed the coolant
Installed a "proper" exhaust clamp
Cleaned the carburetor
Rebuilt the carburetor accelerator pump
Checked and fixed the valve clearances(THEY WERE WAY OFF)
All of these things together fixed all the problems!
The problems were: popping on rev and deceleration, weak throttle response and weird gurgling noises coming from the radiator.
Thanks for watching another GoldGuy video!
Support my channel for more frequent uploads:
Follow my instagram @goldguy_official
Patreon: / goldguy
Paypal: www.paypal.me/masonmcalister
Check out my extra parts store on eBay: www.ebay.com/usr/mcalistermoto
Songs: Dusty Fingers - DJ Williams
69 Bronco - DJ Williams
The take down - DJ Williams - Zábava
That’s the best feeling ever when you get your bike right in spec!
Also adjust the accelerator pump spray to not hit the carb slide. That is what the screw is for. It’s called accelerator pump timing. It needs set to squirt and just miss the slide when opening. If it is late or hits it. It will affect performance. CZcams video from Rocky Mountain atv on it
cool never knew that.
It might be overheating from valves beeing too tight thats why you had boiling coolant
Man, clapped !
Leave the cap off when you change water and start bike so you can see it flowing and add if needed
Anyone see the mouse at around @19:38 outside lol
good eye
Hahaha I didn't think anywould would catch that. It was a chipmunk lol, they are always running around my workshop
I haven’t a clue, never seen a chipmunk I’m from the uk so I just assumed it was a mouse or something haha
Good eye 👁
Damn! I read that as moose. Thinking....that's got to be obvious.
A huge tip to fix chain slap on Yamaha, put a few strips of door sealer from home depot under the rubber chain guide on top and bottom, it helps so much
Very knowledgeable at such a young age. You’re going to be great at what you’re doing in the years to come. Wish you the best of luck.
I have a 2004 wr450f and I am currently having the issues you were talking about in the video extreme popping on deceleration, overheating issues etc. I am 100% sure that my motorcycle is suffering from the same issues you described here. Thank you so much for this video
It's the little things that make a difference. Like checking clearances before assembly. With this experience you should be able to tackle any engine! Thanks so much!
looks like you have it on point now. sweet! I dig the way the front will leave the ground with such ease. Sounds like you are launching in second gear sometimes.
All the hard work is paying off.
Cheers from Louisiana.
WIll be looking forward to seeing you and your new bike at the track !
GoldGuy killin' it as usual, mad props son
Yesss been waiting for this one!
Love your videos man - happy for you
Good that you sorted all the issues.
Good stuff love how you explain everything have helped me understand a lot better
Sounds good and looks good congratulations young man you should be very proud of yourself
Great job gold guy sounds lovely
the theme music portions started small then graduated into the full song, that I was for some reason, looking forward to hearing! Goldguy, your pretty clever , aint cha? This video was fregn awesome, from start to end!
You know, I've had identical decel popping since I had my bike some almost 3yrs now, through a professionally complete top end rebuild, cleaned and jetted carb, pretty much everything I could personally throw at it, and still she pops and is hard starting etc.... But, I'm going to have to check the valve clearance myself as I'm almost certain after watching this series that's what I have going on with my 07'. Man I'll be glad when if I can get this thing running close to as good as yours does. Congrats btw, you came into this not really knowing much about this bike, and you owned it
Increase your main jet size and it will not do that anymore.
Had that problem on my kx450f, it’s probably caused by a worn carb body which allows the slide to move back and forth which causes air to leak past the slide. I fixed mine by gluing shims to the slide to take up the slack and it completely fixed the problem. Check for back/forth movement in the slide, if you have a noticeable amount it’ll probably cause leaking. Look for up and down movement as well which is caused by a worn slide. I have a video on my channel showing the up and down movement, didn’t get one of the back and forth movement though.
Since it wasn't getting the extra fuel from the accelerator pump it was lean popping. You fixed your popping issue when you rebuilt the accelerator pump
Keep up the good work my friend definitely track time 👌
You Sir . . Are Awesome! 😎
Definitely take it to the track. Or the trails. That would be an awesome video
I like that intro, 100% better.
Best video ever! Thx
Great job Bro
hmm my ltz400 does that pop sound. the front pipe of my fmf has seen lot better days i have a brand new one i was going to get fit on next MOT for uk road driving. looks like you saved me £40 of work shop time just knowing that as i was going to pay for one hour in the shop to look in to it. thxz man
Just a small tip for ya next time you do a oil change. After draining the old oil leave all the caps off and pour a bit of fresh oil in and let it drain, this way it will help flush out all the dirty oil just like you did with the coolant.
After finishing any bike series you should go for a four wheeler. Specifically a 1986 Honda Trx200SX. They never die, but the parts are sort of hard to get and you have to custom order them. Would make a great series if you found one in bad shape, and bring it to completely working any everything.
Somewhere around 3 fingers between the chain and where the rearward bold is on the slider on top of the swing arm is pretty close to idea slack
You make good work with that yz.
Awesome video! TRACK!
Good job 👍 keep growing
The exhaust sound was totally different after fixing... Thumps up
sounds great man like it should 👍
Great job! Good video‼️👍✅👏 lets get it on the track!‼️🎥🏍🚦🏃
It’s not just the accelerator pump because I rebuilt mine and it would still do that until I tweaked the carb.
Easiest chain tensioning system has got to be the KLX / RMZ 400. It makes it really easy to ensure both sides are equall
6th, yes! Switchback is my local area track, since then I've moved but a lot of memories about that track. Please watch your bolt torques, every time you torque a bolt I cringe, alloys do not take much to strip out.
better use a high pressure radiator cap with temperature gauge. especially going slow on trails you should monitor the temp.
hell ya.feels good to get your bike in good contition.
fknA. nice work dude. 🔧💪
Engine ice is really good bro use it in my bikes and at the shop
The popping is the jetting stick 1 size larger jets in and 100% fixed
Yeah hit the track! But make sure your suspension is set up properly first! Sag, etc.
this feelings man. fuck yes , there you go, much love
What size jets did you end up using I've got an 07 yz450f and I'm gunna put one of those accelerator rebuild kits in cheers mate 👍
It sounds totally different ☮️
Hey GoldGuy, You are missing a motor mount bolt @8:30, May want to get a bolt in there! Keep up the good work!
You are right! I guess I didn't fix all the problems after all 😅. I've been saving that for my next trip to the hardware store. Thanks for watching!😁👍
Your missing a motor mount bolt on the clutch side!
And the bottem engine bolt is missing to
If only bikes like this were available to buy for £500
The other drain bolt is on the otherside that little 8mm is just an oil level check bolt. Change that oil more often that's way to dirty
Butler Pa.... That's up there in Quad Ricers hood. They have channel on CZcams too.
I have an 04 i bought last month and i have similar popping now and it sounds like its coming from up at the valves but theres no signs of carbon or soot emitting out from anywhere on the engine... also i have the backfiring while decelerating which i noticed immediately ever since i bought it.. i wish i could see a video on your valve adjustment fix because i think thats gonna be the ticket to get my bike running as smooth as yours too..? Also i generally try to go fast enough to keep it cool but 1 time i did boil out some coolant when i rode very slowly uphill for about 15 mins with my girlfriend on the back.. these kick start only bikes without batteries have no radiator fans so you need to be moving fast or the radiator gets no airflow and so it just otherwise heats up like crazy if you go too slow for too long..
yeah I wanna see the track video. is it up yet?
Make a video about how much money you have spent on it to get it running. Sick build man. She's a keeper. She rips
Normally popping means its too lean too much air a lean condition would also run hot . And of course valve clearances aswell as coils and sparkplugs can cause issues. You know when its too rich normally as it bogs down when you rev it and fouls up plugs.
Heres a tip I've learned on cleaning and rebuilding carbs. Buy a ultrasonic cleaner that has heating and then use your choice of cleaning chemical. I used Purple power which worked ok but next time I'm using real carb cleaning chemicals. Like chem-dip. Just because I know its carb body/parts safe and can probably do a better job. Plus, that shit eats old gaskets away.
up vote for track day!
Wow that bike sounds amazing now . How’s the suspension feeling ?
Yep why you where backfiring valves where out. Should run like a top now. You think it had power before. And if you hear sound in the radiator you have air in the system. Run it without the cap to bleed all the air out top off as needed. Also motion pro sells a chain slack tool for like 20.
There needs to be s washer. A spring and an oring on the mixture screw tip that threads up through the float bowl. Often they either get lost. Or stuck in carb. Yours had none. It will run way lean without
Nice that you have the woods in your backyard where do you live?
You have to bleed the coolant system not just chuck some in that’s why it’s probs overheating
I want to rebuild my carb but it a twin and not sure what tools i need
Go to the track!!!
U need swingarm cover i then chain wont pop and it cannot be too tight. Cause if u jump and land u can imiadetly destroy it
how many man hours you put in to the full rebuild of the bike now? plus how much money has it saved you over all doing it ye self ? i not had to time to watch all of the vids as of work. but i remb you getting it cheap as it needed a lot of work its nice to see you done it all. by ye self gj man keep up the good work. feck maybe i should put the ltz400 in just to let the shop look in the hour i pay for they can fit the front pipe and run it up down the road maybe a easy fix. bloody bikes they cost me money all the time my little 49 cc moped 4t never needs work arrrr
Yes to track
If te carb is to lean can make more pop or louder pop.. so you changed te accelerator pomp he gets more fuel in higher rpm so no pop..
my friends get on me when i do total rig shit like that exhaust clamp."Why dont you just get one for 5 dollars??" CAUSE I DONT WANNA WAIT A WEEK FOR IT TO COME IN THE MAIL
Did you top of the coolant after you ran the engine a bit?
What do u think it would be if 5th gear slips a little bit
Where did you find your engine? I’m looking for a RMz 250 and I can’t for the life of me find one.
sometimes i use water as coolant (only if i need to) and its never gave me a problem
In winter the water will freeze and crack the radiators and they might rust inside
Mine was having trouble whenyour on the low speed
Pop goes the weasel !
Nice pet mouse @ 19:38
So, how much have the bike costed you so far, and how much were freebies?
Just wondering how it compares to a good running one. :)
So I was riding my 450 and lost all power and I have no compression. Anyone know what it might be
best starter bike ever haha
Hey not sure y but cant email you have a question about the Subaru
can you help i have a 2006 yz450f and i think it has a accelerator pump issue would buying a new carb fix that?
You don't need to buy a whole new carb, just buy an accelerator pump rebuild kit and adjust it correctly.
@@GoldGuyRides hey me again, bike runs good now just needed the carb cleaned but my exhaust came loose where the header and slip on meet it never had a clamp on and worked fine until yesterday and it started popping and stuff can you link me a clamp that i can buy, it's a full fmf exhaust 4.1 titanium but it's an older model of the 4.1
Please remove the pipe clamp. It's an expansion joint, it's suppose to be there. You'll crack a weld. The header and the muffler heat up at a different rate.
Just asking, why didn't you burp the radiator ? You know, run the bike at approx 3000 RPM's with the radiator cap off for around 5 minutes until the engine gets to operating temp, then idle another 5 minutes then put the cap on, then shut it off. You might need a new cap too. Lastly check your valves.
What's the intro music? Nice!
That chain is now to tight .. they call for 2.5 or 3 inches of slack at the back of the chain slider on top of the swing arm..
Good rule of thumb Is 3 fingers
I have a feeling that you're popping issues are because you're still running too lean, your main jets are still a bit too small, your idle jets I think are ok but if you want you could just bumped them up a size or two, I would up your main jet a little bit also, I think that should fix your popping issue, or you need to re-adjust your air fuel mixture ratio, but actually that diaphragm on that accelerator pump is so shot that I'm pretty sure that will definitely fix your popping issues but if it doesn't then go to your Jets
cool video 😘
What's the total including the original $500?
Use some gold and buy a presure washer to wash your bike after riding or at least before working on it
you should add water with that coolant
Yeah take that thing to switchback mx and rip it have fun
What fixed the popping
The chain ant to lose
At least, your bolts wont rust from that oil xd
Is that a mouse running past the door at 19:40? :)
Chain tension looked a tad tight
I think having one stock cam and one hot rods cam in it it will always give you trouble I would suggest getting the other aftermarket cam
Explain please
@@dirtygarageguy I said I think I'm not a engine expert, just aftermarket cams usually lift your valves higher so I figured if he had one lifting high and one lifting like stock he will always have a motor that's trying to work out to different cams I'dk lol if your an expert explain to me brotha
@@quadvloggs6876 ,
Watch his videos. He seems to know his stuff. I'd even venture to call him an expert.