The Charlie Show /// Episode 336 /// Calibration Trouble Shooting
Vložit
- čas přidán 25. 07. 2024
- Calibration of the electronic speed control, is often a topic that gets overlooked or may give us some troubles. This video covers the basics of calibration, as well as some trouble shooting to review if there are problems. The Servo Test is a quick and simple way to get some visual confirmations.
Email us directly - NorthAmerica@hobbywing.com
HOBBYWING Official CZcams
+++++ Cars & Trucks +++++
Xerun series (Professional grade)
Ezrun series (RTR / MAX upgrade)
QuicRun (starters)
+++++ Helicopters & Airplanes +++++
Platinum Series
Flyfun Series
Skywalker Series
+++++ DRONE +++++
XRotor Pro Series (Pro.Filming /industrial, Gov. research)
XRotor FPV "M" Series (FPV Racing)
XRotor Series
+++++ Marine +++++
SEAKING Pro Series (Speed racing)
SEAKING Series (Marine)
Our mission: Help create memorable moments worldwide.
HOBBYWING Factory: www.Hobbywing.com
HOBBYWING North America: www.HobbywingDirect.com
Hobbywing
Hobbywing_
Copyright & Trademark
HOBBYWING is a registered trademark of Hobbywing technology.
#HOBBYWING #NerdTheNewCool #HDUB - Jak na to + styl
A very usefull tutorial, thks for the Info Share!
Just have up-grade the Wife RGT whit one Fusion Pro 1800kv and is Awesome, transforn the truck totally!!!
Hello. Friends! I have a question, can I take my hw fusion se 1200kv apart by removing the screws on the housing to replace the bearings if they break?
I guess I'll pull my "bad" Fusion se off my shelf and try again.
Hi guys, love your channel, can you help, just watched your 336 episode, as my 10bl60 is playing up, for some reason I couldn't get the throttle (transmitter gt3c) to work, when I turn it on solid red led comes on then goes off, when I try to calibrate it after I turn it on while holding the set button until red led starts flashing and beeping the motor keeps moving/rocking very slightly (1 tooth) no green led I press the set button while in neutral the red led goes off as does the beep and motor stops moving, also tried your servo trick taking esc out of channel 2 and replacing it with the servo I still get nothing, can you help, Kind regards. Jason
Please send us an email for some direct support - NorthAmerica@hobbywing.com. Sounds like you've got a channel output issue. Check out our "servo Test" video for some trouble shooting.
czcams.com/video/NWCgbxWIp24/video.html
I have a question. Accidentally hooked battery backwards on xr10 pro. Poped capacitor. Replaced and works fine. But doesn't seem to have full throttle. Is that fixable or trash it?
Would be worth resetting the ESC and triple checking the replacement power cap and the wiring. Typically all that needs to be done, is the power cap replacement, with a genuine Hobbywing Power Cap of course.
What's the best way to reset esc. Don't see the option on my ota? Thank you for the reply. At full throttle light turns solid green. But no top end. Swapped each and car is back to speed
@@wadedavis9344 Under parameters, you can reset the profile of the ESC.
Would be worth checking over the plugs. They can wear out over time, get dirty, and cause losses. Loose bullet plugs after a reverse connection are common. The plug can get hot and deform easily.
Unfortunately my calibration goes green once and then doesn’t do the forward or backwards calibration. Any advice?
Typically, when an ESC "won't" go through calibration, there is an output problem from the channel itself. Check the throttle channel output, "Visually" by using a servo to test the channel.
@@HOBBYWINGOfficial love your work, but I now got another problem with my steering. Is there a way to centre or calibrate your servo?
Need Help : I Need a E SCOOTER ESC 9037.. and I have emailed every person I can find still no help I need a dual motor speed control...this is the Page to help someone help me with a link to buy..
Please make a Trx-4m fusion