I just got my P1200, thanks for the super fast shipping as usual ! I had a bit of trouble programming the modules though. In order to program #'s 1 - 4 I had to hold down the number 1 on the control panel and hold the reset button at the same time. (the light only had to flash one time though) To program #'s 5 - 8 I had to hold down the number 5 and for #'s 9 - 12 I had to hold down the number 9. Without doing this the modules would not program, nothing happened at all. I'm going to do a video on my channel later on since I want to test it to get familiar with using it before I go ahead and incorporate into my shows. You can check my video after 7/22/2017 for the video. I hate to waste igniters but hey, it's going to be fun and I bought quite a lot of them.
@@GBPyro_920 I like it! I used it this past year (January 2020). Its awesome for normal consumer use. Eric is very responsive and provides awesome customer service! You should get one! It spoils you and you can sit back and just push buttons after rigging up your show or set it up for just firing the the fireworks off. I set my system up and every 30 min or 1 hour, I would set off a fountain or aerial.
@@DoinWhatIDo already bought over 100 mortars from him and already got 3 4 cue modules i could pair to the P1200. Looking to do about 40 cues for my show next 4th July
So if anyone happens to be watching this video on the Eve of the 4th of July, trying to get their P4 modules to pair with the P1200, there is one critical step that is not mentioned in this video!! If you follow this video, you will be unable to pair the P4 to the P1200. To fix do this: To pair a P4 you must press and HOLD the corresponding number on the P1200 you are trying to assign it to!!!!! At the same time using the Q Tip press and hold on the P4 until you see 5-6 flashes, when you release the red light on the P4 should flash and the corresponding cue will light up. If anyone needs help with this tonight or tomorrow(or in the future), send me a message. I might do a video to assist!
So my nightmare would be accidentally touching the fire all bottom during the show. Is there no cover for that nuclear button? Haha or would that have to be programmed on a different set?
Is it possible to program the different cues of a module to different channels? Say I want to button 1 of channel 1 to fire cue 1 of module 1 and button 1 of channel 2 to fire cue 2 of module 1, is that possible?
That makes it really strong, damn. I imagine for example 3 fronts and something in the back, you want a sequence of comets in the front to fire at the same time as a shell in the back. So you place 4 modules, one in each position, the three in the front are simply channel 1 cue 1 through 12, the one in the back is "special". Cue 1 of that module is linked to cue 1 of channel 1 but cues 2, 3 and 4 are on channel 2. That way if you hit rapid on channel 1, your shell goes at the same time the sequence starts, and you can use the rest of the cues on the shell module for channel 2. right? Which leads me to a second question, in this situation, can you switch to channel 2 before the sequence is over? Could you even start firing from channel 2 while the sequence is still running?
Dance Artist not sure on your 2nd question. Never tried it before. Most people use this system as a total manual system. Your question has never been asked before.
What if i need one module for each firework? is it possible to program the module in order to when pressing "1" to ignite all 4 inputs on the one module?
We currently don't have a video, but it's easy. Just press and hold the program cue button on the P4 then press fire on the P1200. Repeat the process for cues 2,3 and 4. Thanks.
Currently there are no plans to have a sale or specials in the near future. We rarely have sales, but the best way to keep an eye on us is to watch us on Facebook. Thanks Jacob!
Is the P1200 contoler compatible with some of the other 4 cue modules on the market, I already have a ton of 4 cue modules, curious if they could be paired. They look the same except the label
I just got my P1200, thanks for the super fast shipping as usual !
I had a bit of trouble programming the modules though. In order to program #'s 1 - 4 I had to hold down the number 1 on the control panel and hold the reset button at the same time. (the light only had to flash one time though) To program #'s 5 - 8 I had to hold down the number 5 and for #'s 9 - 12 I had to hold down the number 9.
Without doing this the modules would not program, nothing happened at all.
I'm going to do a video on my channel later on since I want to test it to get familiar with using it before I go ahead and incorporate into my shows. You can check my video after 7/22/2017 for the video. I hate to waste igniters but hey, it's going to be fun and I bought quite a lot of them.
Great video, very clear!
Thank you!
Awesome firing system easy to use
Thank you!
Just placed an order! Can't Wait!!
@@DoinWhatIDo how do you like it? plan on buying one soon
@@GBPyro_920 I like it! I used it this past year (January 2020). Its awesome for normal consumer use. Eric is very responsive and provides awesome customer service! You should get one! It spoils you and you can sit back and just push buttons after rigging up your show or set it up for just firing the the fireworks off. I set my system up and every 30 min or 1 hour, I would set off a fountain or aerial.
@@DoinWhatIDo already bought over 100 mortars from him and already got 3 4 cue modules i could pair to the P1200. Looking to do about 40 cues for my show next 4th July
So if anyone happens to be watching this video on the Eve of the 4th of July, trying to get their P4 modules to pair with the P1200, there is one critical step that is not mentioned in this video!! If you follow this video, you will be unable to pair the P4 to the P1200. To fix do this: To pair a P4 you must press and HOLD the corresponding number on the P1200 you are trying to assign it to!!!!! At the same time using the Q Tip press and hold on the P4 until you see 5-6 flashes, when you release the red light on the P4 should flash and the corresponding cue will light up. If anyone needs help with this tonight or tomorrow(or in the future), send me a message. I might do a video to assist!
Scott Crossfield thank you. I think the programming has changed for this recently.
Why all the "!!!!!!!"? You seem angry.
Thank you so much!! You are my hero!
So my nightmare would be accidentally touching the fire all bottom during the show. Is there no cover for that nuclear button? Haha or would that have to be programmed on a different set?
the fire-all button was actually disabled back in 2017.
Can I purchase 1.4 pro line fireworks with this firing system
Not sure I'm following, but you can shoot 1.4 pro line fireworks with using this system.
I was thinking about ordering this. Is there any way to stop that annoying noise when you press a fire button? There's no need of it that's for sure
I was using a corded mic to the camera and it simply was interference. You won't hear anything when you price fire.
Do all 12 need to be hooked up before you can use the fire all and sequencer buttons?
No, you don't need all 12 cues to be hooked up. In 2017 we disabled all P4 modules to fire-all. FYI
Why was it disabled?
Why does it make that noise every time you press that button?
It's simply just interference with the camera. No big deal. I did not hear it when I made the video.
Does this support scripting and is there an audio box separate from this?
No, it does not. Check out this video czcams.com/video/a2lTQzcAgIo/video.html
Is it possible to program the different cues of a module to different channels?
Say I want to button 1 of channel 1 to fire cue 1 of module 1 and button 1 of channel 2 to fire cue 2 of module 1, is that possible?
Dance Artist yes, it can do this.
That makes it really strong, damn.
I imagine for example 3 fronts and something in the back, you want a sequence of comets in the front to fire at the same time as a shell in the back. So you place 4 modules, one in each position, the three in the front are simply channel 1 cue 1 through 12, the one in the back is "special". Cue 1 of that module is linked to cue 1 of channel 1 but cues 2, 3 and 4 are on channel 2.
That way if you hit rapid on channel 1, your shell goes at the same time the sequence starts, and you can use the rest of the cues on the shell module for channel 2.
right?
Which leads me to a second question, in this situation, can you switch to channel 2 before the sequence is over?
Could you even start firing from channel 2 while the sequence is still running?
Dance Artist not sure on your 2nd question. Never tried it before. Most people use this system as a total manual system. Your question has never been asked before.
I'm very creative, but also poor :')
hopefully I can borrow a system from someone near me to test it out. Then get my funds in order and get one myself :)
What if i need one module for each firework? is it possible to program the module in order to when pressing "1" to ignite all 4 inputs on the one module?
Yes, you can do this.
Any tutorial video?
We currently don't have a video, but it's easy. Just press and hold the program cue button on the P4 then press fire on the P1200. Repeat the process for cues 2,3 and 4. Thanks.
Also are you guys planning on having any deals or specials on any of your products?
Currently there are no plans to have a sale or specials in the near future. We rarely have sales, but the best way to keep an eye on us is to watch us on Facebook. Thanks Jacob!
Is the P1200 contoler compatible with some of the other 4 cue modules on the market, I already have a ton of 4 cue modules, curious if they could be paired. They look the same except the label
I can't say for sure. I do know that their are some products out that appear the same, but they won't actually work.
are there returns if it doesn't work