Avenge-X .25Cal 🛡 Pellet testing Pt.1📊

Sdílet
Vložit
  • čas přidán 26. 08. 2024
  • Avenge-X 25 pellet testing at 50 yards four different pellets
    #pcp
    #airgun
    #avengex

Komentáře • 19

  • @garynasrallah8710
    @garynasrallah8710 Před 6 měsíci +1

    That was a nice video I shot JSB pellets in all my 25 calibers for years, and then when JTS came out I swapped over, cause they shot so much better, it's crazy.

  • @evolve3dprinting
    @evolve3dprinting Před 6 měsíci +1

    Thanks for sharing! Great video!

  • @gmanneod8085
    @gmanneod8085 Před 6 měsíci +2

    Nice job Derrick.

  • @jumperstartful
    @jumperstartful Před 6 měsíci +1

    Like your vids they are a keeper!

  • @raymondmorales8252
    @raymondmorales8252 Před 6 měsíci +1

    Excellent shooting, I did this same test with my Avenge-X synthetic stock in .25 cal (exactly like yours) I own three Avenge-X two classics one .22 and two .25 cal at 50 yards shooting with the 25 grains JSB, the air arms diabolo fields and the rebranded hades FX Atomics 26.6 grains pellets. All the groups were done with 5 shots each, all performed almost the same all can be covered with a dime. Then a few days later I received those same JTS dead center 25 grains pellets and repeated the test and they performed almost the same as the other three different pellets, BUT they were a very tight fit into the breach and because this the side level becomes very stiff and difficult to use, this is way I have no plans to shot with them again because I am afraid they can damage the side lever or the oem pellet probe of my airgun, but its a shame because they are a very accurate pellets and our Avenge-X barrels love them.
    I also compared the JSB, the AA and FX 18 grains pellets in my other Avenge-X classic in .22 cal with excellent results as well. I posted the results and pics of my targets in the airgun nation board my nick name there is Ray_PR if you want to see them…👍😊. PS yesterday I purchased three of those same high capacity Maples aftermarket magazines but for my Avenge-X .22 cal because for an unknown reason I am having some jamming issues with the pellets with this particular airgun every time I shot with the oem magazines it doesn’t matter if its with the standard or high capacity ones, because this lately I am only shooting with the oem single tray until I receive this new aftermarket mags to see if I can finally solve this annoying issue.

  • @FirstStateAirgun
    @FirstStateAirgun Před 6 měsíci +2

    Sweetness brother

  • @stedyone1090
    @stedyone1090 Před 6 měsíci +1

    Very nice 👌
    Looks cold 🥶
    Thanks for sharing 👍

  • @jerryremington9807
    @jerryremington9807 Před 6 měsíci +1

    Great vid keep up the good work

  • @jeansandmyshirt
    @jeansandmyshirt Před 24 dny

    What's the total weight of this rifle with the scope.
    Great video

  • @blindj
    @blindj Před 7 měsíci +1

    Great video I have an original avenger and an avenge X both in .22 and between JSP and FX JTS I've repeated this test difference being at only 40yds (poor vision) and I have a hard time discerning a difference between those three pellets. One time the winner will be fx then jTS then jsb.
    I also notice the first shot almost always gives me a POI shift after I fill up but then immediately settles right in with all pellets. Same with slugs. Thanks for sharing, love these comparison vids.
    My gun likes Patriot javelin/ Zans tied for first an extremely close second NSA. .217 s. Original avenger Barrel seems slightly larger NSA fit much tighter in the X. I think because it is a harder lead mixture and don't squish down as easily as javelin's or Zan.
    Looking forward to the next vid.

    • @raymondmorales8252
      @raymondmorales8252 Před 6 měsíci

      Its always recommend to dry fired a one or two times our first gen and second gen Avenge-X right after they are filled to avoid the poi shift that you’re talking about. Also to minimize this issue try to never past 4000 psi every time you fill the airguns…👍😉

    • @blindj
      @blindj Před 6 měsíci +1

      ​@@raymondmorales8252
      Usually I can avoid the POI shift as long as I just dry fire once. When I fill it though I always file l it to 300 bar. I'm not sure who recommends filling it to only 4,000 PSI instead of 4350. I know it's actually tested to well above 300bar. Either way both of my guns are fairly new the original I got in August and I pre-ordered the X which I got right after they were released. Both of them shoot just fine. I also have an fx Maverick that if I don't drive fire at once the first shot after a fill will be high. So I always dry fire once before I start shooting with any of my pcps.

  • @johndoee3850
    @johndoee3850 Před 5 měsíci +1

    Test it on a coyote/ bobcat/ good size animal.

  • @robsonoliveira3176
    @robsonoliveira3176 Před 6 měsíci +1

    Very nice gun....i hope its comes to Brazil soon...

  • @Jeeper1378
    @Jeeper1378 Před 6 měsíci +1

    I was slinging the JTS 29’s at 850.
    Whats your hammer set at?

    • @gumbystown
      @gumbystown  Před 6 měsíci +1

      I can't remember how many turns in it is on the hammer spring I we'll have to check.

  • @scinner28
    @scinner28 Před 3 měsíci

    ow boy .25 Jsb etc .etc. did you use the 34gr.jsb ,fx,jsb mk2 etc with this gun???NAAAH ..rofl ...why?

  • @guillermocastilla6305
    @guillermocastilla6305 Před 6 měsíci +1

    Have you done anything with the under lever beeman

    • @gumbystown
      @gumbystown  Před 6 měsíci

      I still have it and the only things I've really changed to it is added a metal shroud - donnyfl moderator adapter - Buck rail Barrel band Picatinny mount - Robert Lane regulator and some trigger work she's a nice shooter I need to drill the transfer port to bump up the power but I still have it.