Building an FPV Cinelifter - wiring to programming
Vložit
- čas přidán 27. 07. 2024
- Take the shot everytime i say quadcopter instead of octocopter.
-
Chapters:
0:00 The Mission
0:19 Introduction & Some tips
1:50 The Build
9:06 Inav Configuration
16:10 Calibrating Compass on field
16:40 Maiden Flight
-
Wiring Diagram:
drive.google.com/file/d/1T_yr...
-
Parts List:
1 X x8 Frame - Shendrones Thicc 2.1 1:52
Carbon Only step by step video: • Shendrones Thicc 2.1 F...
8 X Motors - Axisflying AF310 1210kV 2:19
2 X ESC - Reaper F4 65A 2:39
2 X Plugs - Amass XT90s 3:08
2 X Capacitors - Rubycon 2200uF 50v 3:52
2 X Spike Absorbers- Rush PFB Lite 3:57
1 X Flight Controller - Matek H743-Slim 4:20
1 X RX - TBS Crossfire Diversity 5:39
1 X Video - DJI Air Unit Fullsize 6:21
1 X Matek 9V BEC 6:40
1 X Buzzer - JHE42B-S 7:15
1 X GPS - Axisflying 7:56
2 SETS X Ethix Propeller 7X4X3 & how to install 15:15
1 X ZEEE 5200Mah 6S Lipo (Not specified in video)
1 X A6300 Sony Camera
1 X Sigma 16mm Lens - Jak na to + styl
Great video! Should have 10x the views
Great video, sweet flight congrats! Thanks for sharing
This was really helpful. Thanks
nice build bro
Thanks bro 😬
Nice build Bud
thanks bro ✌
Like your presentation, btw what was the total weight of the dslr including lens ?
Nice build 💪🏻💪🏻.
My dream is to learn positionhold tutorial from you 😅🙏🙏🙏
haha sure bro,
Actually in Inav just enable the switch on the Modes tab, and make sure you got a GPS with Compass. Then Allign the Heading with a compass like I show in this video:
czcams.com/video/2MBYfAa9LjY/video.html
Is it possible to using speedybee f405 v4? Because in their description it's support 8 motor
Thank you for this tutotrial!
But I have a problem. On the same FC, my air unit doesn't work. I used the bec and everything but it seems like the air unit does not receive enought power to work. Do you know what could it be? Thank you.
Just to make sure bro, did you bridge the 9V pad at the back side of the BEC?
Cuz if the two pads are not shorted the bec is emitting 5V
@@TanFK Yes man, I did it as you showed in the video, but didn't work
@@PabloUrba my suspect might be a faulty BEC. You could check a multimeter on direct voltage [V].
Positive Prong on 9v out of the Bec and Negative Prong on Gnd of Bec, Multimeter should show around the 9V range if the BEC is working,
if your BEC's not at fault, you might want to try powering the Air unit on another quad to also check if the Air unit is OK
On a random note:
I dunno if you're using a Diatone BEC, but I've had a friend who used a Diatone BEC on the his cinelifter and it shorted itself on his first few flights, so avoid those.
@@TanFK Yes, checked the air unit on another quad and worked fine. I tryed with 3 becs. On the cinelifter fc i have got the message 'Image transmission stopped' showed on the dji googles.
Very strange..
But the next step I’ll try:
To power the BEC, you could try soldering it straight to the ESC +/- leads to test first.
It’s no problem bro I’ve done it before, there’s continuity between FC VBAT pad and your ESC (+) lead.
Doing this will just close the distance of your BEC to the lipo
Had the same issue with the smoke stoppers. I woulder if one could be made specifically for cinelifter type builds?
I’m assuming here but I think the solution would be the XT 90 8s rated smoke stopper should be able to get the job done.
For now the xt60 6s rated doesn’t work regardless which battery I try
@@TanFK I also had to do the plug and pray 🙏 🤣 luckily I was all good 👍
It’s so weird even my multimeter was red flagging me on the check. 🤔
I held my breath, counted to five and then plugged it in. It just felt like the biggest gamble on my bench 🥶
Hello from Russia! And please tell me what kind of fan you use at the end of the video?
Hello!
Sorry for the late reply, I missed your comment.
I use the Cenzimo Air Duster, its good at cleaning my fpv bag from dust, but not good dust removal for drone... I still need to brush my quad after dusty session, so i recommend you search 'electronic air duster' and find a better brand..
No matter what Aerosol Duster cans are #1 for performance, but I compromise with electronic as a sub-par solution because I feel bad about throwing away empty cans.
hello! can you share the stl for the platypus?
I've put in the Original Platypus (not available online anymore)
and the modded one I did with no GPS - Cuz the GPS got in the way of my wiring
Hope this helps.
drive.google.com/drive/folders/1BrduP9keP31R6ON8_Oeiu3dJXrLNc-kh?usp=sharing
@@TanFK Thank you! Love your content.
Hi, do I need bridge on vbat on fc?
Hey could you elaborate on what your asking about?
In terms of power
One XT90 set will split to two escs giving power to both escs.
One esc can then supply power to the flight controller with signal wires 1234
While the second esc only needs signal wires 5678
@@TanFK hi, I meant that Bridge on FC, Vsw = Vbat 5v. Also, do you connect power and ground on both esc to fc? I fought that Vcurrent and Ground plus all Throttles on the slave esc. Thanks. Jakub
@@AirviewDroneScotland
1- the VSW on the front part of your pad will emit Vbat if you bridge the centre pad with vbat, while it will emit 5v if you bridge the latter. You decide what the vsw pad does by joining it.
2- it’s not necessary but yes I connected both esc’s vbat and ground to my fc, because at the chance one esc fails, the other esc can continue the circuit reliably(that’s just my theory)
As I read, You just don’t need to connect the Uart wire or current wire on the slave esc to fc.
current from 2nd esc? didn't used?
yes bro.
ESC 1 - Everything including current and telemetery I wired on JST.
ESC 2- Vbat, GND and Signal ONLY.
I can still have accurate reading of my battery no problem.
____
Why I didnt wire it to esc #2 is because on the FPV Cinelifters facebook group, I searched
'ESC Wiring'
and there's one comment saying connecting both current wires will blow the FC.
So I played safe and didnt wire those.
On a side note, the Facebook group guy was refering to a Lux F7 Flight Controller, So Im not sure if this would also apply to Matek Flight Controllers.
@@TanFK thanks mate, I've also searched some literature on cinelifter x8, but confused with 4in1 esc which has current pad, I'll try to build my x8 using matek F722 SE and other cheap kits 😅
@@pilotlawaran more common, 4 in 1 escs have current pad but no telemetry pad. but actually you can live without them.
Ah I see. Matek f722 se. I Managed to get it to fly X8. Just note you’ll need inav x8 firmware flashed to see all 8 motors yea
@@TanFK nice info 😀
Mohon aku butuh wiring diagram
drive.google.com/file/d/1T_yr0Lw-iETtjmkL7dip2O4Tc9h0GDGn/view
could you post a wiring diagram please
Here you go bro
drive.google.com/file/d/1YFQriHqTokpv2YKM0TUOmf0Q-ozRQZJa/view?usp=sharing
@@TanFK thankyou