Removing Stuck CV Axle from HALF SHAFT - SIMPLE - Passenger Side CV Axle Stuck
Vložit
- čas přidán 4. 06. 2021
- A simple solution to remove a stubborn, stuck CV axle from the transmission half shaft with no special tools. This was on a Honda Pilot but will work for all makes and models.
More About BundysGarage:
goo.gl/qv3Wzc
Questions, Comments, Concerns:
bundysgarage@gmail.com
Twitter:
/ bundysgarage
@bundysgarage
On The Web:
www.bundysgarage.com
Music by Randall Kent: As seen on NCIS
• Randall Kent - Going H...
All Rights Reserved 2021
© Copyright 2021
Bundys Garage
All rights reserved. This material may not be published, broadcast, rewritten or redistributed in whole or part with out the express written permission. Contact: bundysgarage@gmail.com
DISCLAIMER - DISCLAIMER - DISCLAIMER
Due to factors beyond the control of BundysGarage, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. BundysGarage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. BundysGarage recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of BundysGarage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the end user and not BundysGarage nor any of it’s subsidiaries. - Auta a dopravní prostředky
Man you are a genius, spent 3 hrs trying to pry the axel out, both axels were the same and wouldn't move... 3 tries on both sides using your method and both popped out!!! Thanks man, that's an awesome tip!!!
Your welcome!
@@bundysgarage bad luck , it’s not worked for me 😟 trying to remove cv axle bracket last bolt I have to remove catalytic converter Iam trying again now your method Should work but I don’t know why it’s not working for me 😖😖😖
@@Sroor2023 didn't work for me either 😡
Same here 😂😂 I wish I watched this earlier
Could I heat the opening up to try and expand it ? And then pull it out that way
Bruised, bloody and absolutely OVER IT, I took one last swipe through youtube and stumbled upon this godsend of a video and was gifted a golden nugget of your expertise. My busted half shaft will be cleaned and used as a chalice with which I shall toast to your good health.
Exactly how I felt this man is a godsend
I’m currently feeling this pain with cuts and bruises
My knuckles hurt so much. If this doesn’t work tomorrow so help me god
Relatable
From this point when got it partially I would’ve jacked it and used a pry bar
Tired, broken, and frustrated? This video will save you. Thank you for posting this video. You are a good man.
Howd you cut off the boot i dont have any metal cutters but ill do whatever it takes including buying more tools to get this thing the hell out of my car. Have already ripped off the cv axle with an axle puller and have the half shaft stuck in there and can go buy vice grips
This trick is one of the best I've seen on youtube. Saved me a ton of headache and repair bills. Thanks a ton!!
I just finished changing the cv axle on my 2018 drivers side Nisan Altima, you know, the one that's just supposed to just pop out. Well, it didn't pop out, it didn't pry out and I'm working on in my car port on the ground and was about to give up and take it to a shop last night when I saw your video. I cut a slit in the boot up against the cup of the inner bearing holder with just enough room to fit the head of vise grips. I was going to give it a couple of test tugs and on the first tug it popped out. My life is complete.
Glad it helped you out! I know that feeling of frustration and defeat and then when it pops out, oh boy, what a relief!!!! 😮💨
I fought tooth an nail last weekend getting mine unstuck. Used the vice grip trick first try this morning and it popped right out. I almost didnt believe it happened. You're a genius sir, thank you for sharing your big brain tricks
Howd you cut off the boot i dont have any metal cutters but ill do whatever it takes including buying more tools to get this thing the hell out of my car. Have already ripped off the cv axle with an axle puller and have the half shaft stuck in there and can go buy vice grips
Glad I looked this up instead of spending a few hours trying to pry it out. Definitely saved me a lot of time and frustration.
Blood sweat no tears been here 2 hours trying thank god you posted this video got it done in 5 smacks god bless u man
Dude this is the single greatest most helpful mechanical video I have ever seen thank you so much
Hours had past, I had tried everything and was in time crunch. Almost gave up . But like most of the people who found this video, I took one last look through CZcams. I was blessed to find this video and in two swipes it was out. Thank you for making this video. God bless
Glad I could help
Howd you cut off the boot i dont have any metal cutters but ill do whatever it takes including buying more tools to get this thing the hell out of my car. Have already ripped off the cv axle with an axle puller and have the half shaft stuck in there and can go buy vice grips
Listen, it was Thanksgiving even and I decided to replace the axle since it came in two days early on my Mazda 3. It broke off. I looked at so many other videos then came across yours. It came out after 5 pulls. You’re a LEGEND and a life saver especially since everywhere is closed today. Thank you so much!!!!
Glad it helped you out! Happy Thanksgiving!
@keketv860 was it the driver side or passenger side 🤔. I have the same car and my passangers side is giveing me hell.😊
@@BTKKILLER1 I had this issue. Passenger side has a bracket with three bolts (14 or 15mm I think) that needs to be removed first. It’s halfway down the axle. It’s a bitch to get the top bolt (it’s in a triangle formation). You’ll need a swivel head and an extension.
Holy moly! Thank god I found your tip!! It worked. Spent hours trying to pry the stuck cv axle on my kids 2013 passat. After 15 seconds of using your tip, popped right out! I really appreciate the time you took to share this tip! Saved dollars and saved learning new cuss words!
Same here - Thanks SO much... spent ages trying to do this, didn't have a slide hammer, spent ages prying and trying to get it out. Had to put it all back together that day. Saw your video that night and did it with your method the next day in 10 seconds. Life saver - praise be to CZcams!
Like others here took one last swipe through CZcams looking for a solution to this problem. Two pulls and it popped out, after spending an hour or more cursing at it. You saved me 70 bucks for a slide hammer kit. Thank you.
Howd you cut off the boot i dont have any metal cutters but ill do whatever it takes including buying more tools to get this thing the hell out of my car. Have already ripped off the cv axle with an axle puller and have the half shaft stuck in there and can go buy vice grips
@@bobthebuilder9416 it’s been a minute since I did this job. Cut it with a knife unless you’re trying to save the boot for some reason. I am thinking you can pop the clamp holding the boot with a flat head screw driver. Otherwise I’d buy a pair of tin snips.
@@chadehresman6952 okay thank u so much ill try it later this week
Thank you so much, I finally got my passenger side axel out with your solution. I tried prybars, slide hammer, cv axle popper forks and nothing would budge it. It took me about 45 minutes today to get it out this way. Anyone still having problems doing it this way, what worked for me was pull it like 3 or 4 times, rotate the cup like an inch and pull it like 3 or 4 times and repeat, on the 3rd turn I got it out on like the 3rd pull and I wasn't pulling very hard because I didn't think it was going to work. All in I probably spent 12 hours trying to pull this damn thing out and I got it out in under an hour with this trick. Thanks so much.
Bundy, this is ingenious. I can’t believe it didn’t work for you. I was a little downcast after I watched your video and your shaft did not come out. I tried it anyway, and my shaft popped on the second pull. I can’t thank you enough! (Yes, I said my shaft popped on the second pull…:)-
So after 3 hours of blood and sweat, where I gave up not only my car but also my life, I found this video, you saved me, thank you, you don't know how much this helped me. May God give you happiness and love!!
Howd you cut off the boot i dont have any metal cutters but ill do whatever it takes including buying more tools to get this thing the hell out of my car. Have already ripped off the cv axle with an axle puller and have the half shaft stuck in there and can go buy vice grips
Hey Bundy, seriously like Phil just said. So I have been working on pulling out my passenger side CVX out of our 2013 MDX and have been working on it for the past 3 hours (morelike 3.5 hours) and nothing... would work to get these thing out. The half shaft got stuck, and I used pryer bars, and nothing... I just discovered your video and removed the grease, put the bearings back on the end of the shaft and put it back inside the half shaft, clamped down with my Milwaukee Torque Lock Curved Jaw Locking Pliers and pulled and guess what? it came out on the FIRST pull!!!!!!!!!!!! Dude, you rock..... Thank you, thank you, thank you!!!!!!!!!!!!!!!!!!!
Brother it worked for me and I was feeling discouraged 😅 until I came across your CZcams channel saved my day 🙏 thanks
Man what a lifesaver. I was stuck with no place to go. On a 2002 Dodge Caravan that inner CV joint is recessed up in there where you can’t even use one of those special tools however your method works like a champ. I can’t say thank you enough I really appreciate it
I don't ever comment but this saved my FREAKING LIFE. Nothing was working but this got that boy loose almost immediately!
Thx for the comment and I’m glad it helped you out! I know the frustration of trying to get one these out when it’s stuck and then the victory that washes over you when it pops out!!!
Howd you cut off the boot i dont have any metal cutters but ill do whatever it takes including buying more tools to get this thing the hell out of my car. Have already ripped off the cv axle with an axle puller and have the half shaft stuck in there and can go buy vice grips
Oh man THANK YOU. I've been fighting with this exact issue for about a day and a half with a 2015 Honda Civic EX and this actually solved the problem. Really appreciate the video man. Saved my day.
I spent most of my day trying to get one out. I decided to search for another way on youtube. First method did not work. Second method involved me having to go buy a slide hammer.
Then I found this video. 3 yanks and it came right out.
Thanks a bunch for the tip!
Glad you got it out!!! I know the feeling of frustration and wanting to get on with your day and fix your car.
Howd you cut off the boot i dont have any metal cutters but ill do whatever it takes including buying more tools to get this thing the hell out of my car. Have already ripped off the cv axle with an axle puller and have the half shaft stuck in there and can go buy vice grips
The boot is rubber. I cut mine with a box cutter and a fresh blade
@@virider7466 great thanks
Thank god i found this video! When all else failed, this ended up working within 5min
I know your pain.
Just did this on my 99 Honda CRV and it worked like a charm! Three pulls and it was out! Super helpful!!
Thanks bro I was ready to put a match to it, you know how it is when you bust a couple cold fingers trying to pry something out. My car thanks you, my neighbors thank you and I thank you, did it just like you did and it popped out on the first try thanks again man I'll be looking for your how to O's when I run up on another mess, this is the most helpful video I've ever watched. Don't mean this in a bad way but I thought I was the only one this stuff happened to lol. Have a good one man, thanks again
This is genius!! Spent 3 days trying to pry my axle out. No friends have had the tool or an idea to remove it. Didnt wanna buy the tool just for a one time use. Thank you for sharing you're great idea!!💯🤙🏽👌🏽
Improvement on your method: Part of the problem in getting these things off is the offset force applied by either a prybar or your method. Try putting a visegrip on each bearing (three visegrips), equalizing the load on the axle.
Good point.
Or take the visegrip and and undo it and move it around so all the sides get the same amout of force
This is the method that worked for me! Thank you for the video! Saved me so much time after already spending six hours trying to get it out
My dad was struggling with the broken cv joint on his 2001 Toyota Corrola for about an hour.I found this video for him.He ran and got his vice grips.He got it out in 30 seconds.Thanks for sharing.
Just wanna let you know I’m commenting right now because you deserve the credit man I was lost and beyond being completely over taking this axle out so I looked up your video and the vice grip trick worked like a miracle thanks man I appreciate it. Please keep making more content.👌🏼🙏🏼🙏🏼🙏🏼🙏🏼
Ok. I'm another happy amature mechanic. I tried for hours. Prying, banging, rotating the stuck piece (like one of my favorite youtube honda mechanics suggested). Nothing. I tried this first with grease still on the part and the plyers fell off. Then I made a "clean" spot, repositioned the vice grips and "hammered" it this way about 12 times then pow! It fell right out! Only took about 15 minutes. Thank you! Now I can complete this "realitively easy" job! 👍
Glad it helped you out!
Howd you cut off the boot i dont have any metal cutters but ill do whatever it takes including buying more tools to get this thing the hell out of my car. Have already ripped off the cv axle with an axle puller and have the half shaft stuck in there and can go buy vice grips
@@bobthebuilder9416I think the rubber boot came off when the axel seperated because I had a broken lower ball joint. If I needed to I think I would have cut the rubber boot (with tin snips, scissors, etc) which for me was ok because I was installing a new axel assembly.
Bro. You. Are. A. Lifesaver! I've been struggling for an hour half on this. After about 5 minutes of this, I got it out.
I feel your pain! Glad you got it out.
Brother, I cannot begin to thank you enough for this ingenious idea. I was truly defeated upon finding this video which gave me the hope to try one last time. It took a good 15 pulls but that SOB finally gave. Free 99 FTW
This works guys!! I was struggling for 3 days trying to get my cv axle out of the transmission, tried this and it popped right out on the second pull. Thanks so much my man
Wow, I fought my broken cv, then I saw your video. Popped out the cv on the second pull. What a life saver, thank you!
Nice tip Mr. Bundy. I had a hell of a time getting mine out of the drivers side Honda Accord. I still have the old axle so now I’m glad I kept it to use if I have trouble in the future. Artie 😊
Thank you! This just saved me soooo much extra struggling and effort. Just wish I looked it up 45 minutes sooner. Haha.
Thank you so much, I spent 2 hours trying to get the CV releases before watching your video and had it out in 3 plunges with the old axel... So smart...
This was a life saver for me, I had tried to remove my cv axles for many hours and nothing worked, then I tried that and it worked instantly
Wow, this method was a life saver. Spent a couple hours trying to pry and wiggle it out until I gave up. Then I stumbled upon your video and gave this a try and it came out after a couple of minutes. Thanks so much for sharing!
THANK YOU! I HAVE BEEN STUCK ON GETTING THIS BLASTED THING OUT FOR 3 DAYS
THIS SHOULD BE THE FIRST RESULT
You sir are a saint for this, was struggling for hours with a sledge and pry bar and all it took was a few tugs with this method. Thank you!!
I have to say, this worked like a charm on a Chrysler Sebring I’ve been working on for a co-worker! I’m so glad I watched this vid! The problem was caused by a ball joint on the LCA pulling the CV out, and it’s been some other problems. I pulled like 3 times and got that end out. This was magic! MA-JIC!!!!
Hell Yeah!!!!
Was just fighting my 2005 pilot for two hours, was bout to give up and seen this and it came out in a matter of minutes. Great video !!!!
Feels good once it finally “pops” out! Hell Yeah!
You Sir are a blessing from god 😂 been working on this CV for 2 hours and this worked in 45 seconds! Thank you!
Man, I did this and it worked on the 3rd pull! Your a lifesaver. Learned a awesome trick today
It has single handedly saved me money and time, and from the bottom of my heart, I can't thank you enough good sir. thank you
Hey bud you are a genius ain't nothing like the old school way. I spent hours trying to pull mines out. Then when I saw your video I remembered that's how my grandfather usually get broken axle out. Free 99 baby love you man keep making more videos like this.
Glad it helped you out!
I just want to tell you how much I really appreciate you and your awesome video. Just did mine today using your method and brother you 're method works like a champ...very simple and easy....no more frustrations and yes I don't even need those expensive tools. You're a genius! and brother Thank you so much and God Bless You!!!
I was routing for you I had the same problem. Came in and watched your video went out and it worked right away. Thanks for your help
Best tip so far I've seen...did driver's side already on a 06' Kia Sedona, the passenger side is being a pain...about to try this. Thank you!!
I cannot thank you enough. I spent forever on the drivers side and finally got it. Then the passenger side did the same thing and thankfully I came across this video and it saved me so much time
You saved my bacon on my 09 Scion. I absolutely tryed every tool..all failed to remove the stuck axle shaft. This method worked the first try. Thanks for posting this video! 👍👍
First try using this method after hammering for 2 hours and it worked beautifully 🙌🏽 thanks man
Have to say that this came in handy for me. Could not get a CV axle puller on my Nissan Altima 2012 SR model. A little PB Blaster then used your vise grip method and SUCCESS!! Thanks for posting.
Hours a cold garage floor, cant get the door shut, snow pouring in, no heat, beating the snot out of the thing trying to get it loose and your tip got it out in 3-4 whacks. I am amazed and humbled.
Thank you!
At least it wasnt 100 degrees like it is here in florida today 😂...i was defeated and now I have a glimmer of hope and a dream.
Did it work for you?
This trick worked like a charm after much fighting and prying ..
definitely works using old axle as a slide hammer !!!!Thank you ..I set it up with the old axle and vise grips and after some failed attempts (guess I'm not strong enough)I grabbed my daughters bf and had him do it and it came right out !!
@MelissaGabbert glad it helped you out!
My husband couldn’t get this shft thing out for a whole day i watched ur video and not even 20sec he got it!!!! Thank you soooo much!!
Thank you so much. Surprisingly this worked extremely well. I purchased a slide hammer with a cv axle attachment that didn't fit. This did the job in about 10 pulls.
You are my HERO! Definitely GENIUS idea...tried it about 4 Yanks and boom she came out..... thank you thank you!!!!
Thank you this was perfect, no need for fancy tools! Saved my ass from sending to a shop. Now i have the confidence to fix the other axle! Bravo sir!
Life saver! spent hours tryna pry out the axle til i came across this method. thanks!
Brother. Wow. You are a TOTAL and COMPLETE genius. Like Phil Brown below, I spent the better part of 3-4 hours trying to get that remaining piece out of the transmission after it decided to stay behind and just let go of the rest. I was trying to come up with anything I could think of, but the Hulk inside me would not abide! Thrown tools, a 30ml bottle vaped in that three to four hours, and a screw-it attitude ALMOST got me...YOUR VIDEO WAS AWESOME AND YOU SAVED ME SOME REPAIR COSTS ON STUFF THAT HAD NOTHING TO DO WITH WHAT WAS GOING ON AT THE TIME! Thank You, Man!
Glad it worked out for you!
Woo! Thank you very much for thinking outside the box, and then sharing it! This worked within 10 strikes on the driver side of a 2010 Nissan Altima 2.5sl CVT.
Hi. Your method worked great on my 2002 Taurus cv axle. I could not get any leverage / clearance to pry the socket out and then I remembered this video. One good pull on the shaft and - out it popped. Brilliant! For those viewers having trouble with this method, I suggest trying to rotate the spindle inside the socket ( may have to put the ignition in ON position and use the tire on the other side to allow the rotation.) This changes the position of the securing ring at the spline’s end. I did not have this problem but I read that other commenters did. These types of CZcams auto repair tips and techniques are invaluable for us DIY guys. Thanks.
Glad it helped you out!
This worked so well. Three pulls on the the 'axle shaft slide hammer' and out it came. Thank you so much.
You are my saving grace. IT FRIGGIN WORKED!
You’re the man!!! I was so frustrated with the CV on the passenger side of my 07 accord v6. I spent 5 minutes banging on it with your method and out she came. Lubed the new one and slit it right on. Before I tried your trick, I spent a hour trying to pry it but could not get any kind of pry tool in there. Thanks again man!!!!
Wow!! I literally went on CZcams to figure out what fancy tool I needed to order and this video absolutely saved me! I only had to tug five times and it was out!
Just wanted to say thanks. I was getting ready to weld a makeshift slide hammer and came across your vid. Worked like a charm and hats off to you good sir!
my friend being struggling doing this and i started to searching on youtube and find your video 🤣 u are lifesaving
Yep, that was the way to do it on the drivers side CV joint of my 2005 Town and Country! Life saver video. Thank you so much for the advice!
Thanks for sharing this, I was having a bad day until I watched it. Worked like a dream.
This trick worked beautifully 100%. Thank you so much, you made my life so much easier with this little hack. Definitely gonna keep looking at your videos.
Your a life saver. Spent a whole day trying to remove CV axle. Went and purchased an axle puller/hammer slide and that didn’t work either. Did this method and in one pull it just slid out.
Thanks it really helped my hands are sliced everywhere then I saw this god sent this really works
Me and the boys fought with a cv axle for my lancer for about 4ish hours and I opened up CZcams and had it off within 5 minutes after watchin your video, great job bro 🤝
Was pulling on mine for 30 minute and literally took 2 hits to come out, my man👌🏻👌🏻👌🏻
Dude, you just saved me as you did so with many many others, thank you
This helped me tremendously. This was my first go around ever cause I am not mechanic but I was able to use this technique!
Glad it help you out.
Bundy it is safe to say you really outdid yourself with this video,I was struggling with a 2010 Acura Tl for hrs even rented the slide hammer tool md nothing.called it a night,watched a couple videos but nun like this ,tried it next morning got it out within 30 seconds or 5 pulls💯deff works💯
This worked for me, after trying other ways for a long time. Found this and I was able to get it out in five minutes. Thank you
Took me 3 hours to pry the crap out of the passenger side and told myself theirs gotta be a better way. I watched your video and man it saved me more time from getting all those bruises from tight spaces when I did this method to do the driver side.
Thank you very much sir !
Was going to comment how much of a life saver this video was but it looks like everyone did that already. Thanks for the tip!
Another comment won’t hurt, plus it shows the YT gods that this is a good video and it will recommend it to more people.
It worked first time I tired it on a 98 Plymouth breeze.. thank u so much for sharing and helping others
Just did ur method I owe u food or something been trying for the past 2 days doing other ones but ur was the one that got it much love
Worked on the first tug, thank you so much for making this video !!
This incredibly simple solution (which I *would not* have been able to come up with) saved my bacon yesterday. Thank you very much.
most intelligent, creative, thinks for ones self solution I've seen so far. Mine's still stuck but. But well done you Mr Bundy.
It came out so quickly using this method. One tug. So little at and not much leverage with up on jack stands. I even pushed with my leg. Several hours wasted until i found this video. Thanks Bundy!
Glad it helped you out!
After 6hrs trying busting knuckles and everything next morning took 45 mins including breaks thank you sooo much life saver
Because of your video I was able to get my CV axle off on the side of the road I already had my spare in the car and I was going nowhere but because of you in this video and the mind God gave you I was able to fix my problem
This method works so glad I found this video!!
I tried the sliding hammer with the grip adapter and no luck. The threads on the adapter and the locking pliers strip. With your method it worked so fast after many weeks of trying. Thank you so much !!!
Great tip! I used two sets of vice grips to even the pull, popped rite out. Thanks
After watching your video I was able to get mine removed. I used pry bars for like a hour with no luck. A few strong pulls on the axle with you setup and it popped right out. Thanks.
Oh my god this is insane, this was so effective, thank you so much; so glad I came across this. Worked beautifully, and now I can return that slide hammer that didn't fit!
Thank you
Great idea, thanks ! Worked perfect to be so simple. Many thanks again!
I don't go to church anymore, but this time I'm gonna say thank you Lord. Almost all day going back and forth to Advance auto and their ineffective methods. Two pulls and it's out. Thank you sir for downloading this video.
You are welcome my Son!
Bro, i wish i found this video 4 hours ago. It worked perfectly for my 2013 outback. Thank you!