Video není dostupné.
Omlouváme se.
Whirlpool Gas Dryer Not Getting Hot - Check The gas valve
Vložit
- čas přidán 28. 04. 2016
- Whirlpool Gas Dryer Not Getting Hot - See What Parts to check & replace to fix it
Replacement parts amzn.to/3wv6dwN - paypal.me/Ange...
Warning: You can use the information in this video at your own risk
This is the BEST most easy to understand video out there on checking the parts of a gas dryer for proper operation.
This is the BEST video out there, thank you!!
I join the other comments in saying this is the BEST instructional video on checking why the dryer doesn't heat. Love the wire trick for securing the drum! Clearly shows what parts to check and how to check them! Thank You!!!
The igniter clip sealed the deal for me! I had already replaced the solenoids before i watched this vid, turned out on but still no heat. Watched 1st couple seconds of ur vid, checked my igniter & it wasn't firing, so i threw in a new fuse, turned it on & viola! Dryer firing & working. Thank you! I cleaned out the machine while it was opened up & the blower too (it was all gummy & linty).
one of the best youtube videos on the subject of dryer.repair.to the point and very easy to understand .love the wire trick to hold the drum.I also like the idea of changing the coils after seeing the igniter light but the dryer does not keep operating properly.well done mr angel.
You're a life saver! Continuity in everything but I didn't trust the gas coils and valve. I now changed the coils and it's working just fine!! Thank you very much. Funny, the last thing to check and there was my problem.
Thank you for your thorough and step-by-step video. I am very grateful.
Step by step instruction and easy to understand.Thank You!
Thank you, I used this video to solve my issue. It was the fuse.
Definitely the best video on subject! I was able to fix my Kenore dryer. Pronto!
I miss the old man's voice the digital voice threw me off. Still it's quality instructions by a professional.
This was the best video in the world it was so great to get me threw it
thank you very much, this video help me a lot, now my dryer is working fine again :)
Excellent video--very, very, helpful. Thank you!!
Thanks for watching my videos:
For more free videos that will show you how to fix your washer or dryer, visit my website
www.do-it-yourself-washing-machine-and-dryer-repair-help.com/
Angeltheapplianceman
Excellent video thanks keep it up
Excellent video. Solved my problem perfectly. Thanks!!
My dryer is short cycling. Ignitor glow, gas flows and burns for 30 seconds. Then the flame goes out for 2 minutes. Then the cycle repeats. Clothes are not drying properly. I have checked for continuity across the switches. All switches have continuity. Is it possible that the heat cycle switch is getting weak and causing short cycling?
very good video thanks
Muy buen video vien explicado sin tanto arguende..👍 Gracias bro.
Just installed a brand new Whirlpool natural gas dryer in my home and the burner comes on for only about a minute or so, then goes out. Through the peep hole I can see the ignitor glow for about 7 seconds then go out while the drum is turning. After about 40 seconds or so, the ignitor will glow again for about 7 seconds then die down. This cycle repeats over and over. This is a brand new dryer that was delivered to my house from Lowe's and it is doing this. This replaced the Kenmore dryer that was 1970's vintage that was still working when I received the new Whirlpool. I repaired that Kenmore myself over the years and kept it in good operating order. Now I regret having gotten rid of it for a brand new "made in China" piece of shit that doesn't work. For $920, I now own a clothes dryer that doesn't dry clothes. A service tech is scheduled to come check it out next week. It is brand new and under warranty so there's no way I am messing with it. Let Whirlpool fix their garbage. They used to make good stuff. Not any more.
Did they fix it? If so, what was the problem and solution?
I hear a buzzing when the igniter lights but no flame could it be the coils?
Note to Maker of this Video...
@ 2:57 time stamp...
You call this component a Hi-Limit Thermostat...
But, that Item According to my Dryers, Wiring Diagram, has that part, listed as a Thermal Cut-Off, Part#280010, and also the Temp. Stamped on new part, says 352°F Degrees, and same 352°F degree temp. On Wiring Diagram....
👉 The Thermal Cut-Off, has a wide plate, shown as bottom Item. Part#280010.....
The Top One,
Is the Hi Limit, Thermostat, 205°F
Part#3403140....New WP item, says,
L 180°-35°F (L=Limit,Hi)
Which has, kit number W10754607, listed on, the side of Hi-Limit, 205F thermostat, and part#3403140, in parts list...
Mine, is a 2005, Gas Dryer, Kenmore 80 series, and has a
Model# 110.76832500,
Serial# MS 2002169
I have a 2009 Whirlpool Gas Dryer modelwgd6200sw2 that starts up, heats up, then turns off, and does not heat back up.I replace the dryer thermal fuse and the high Limit Thermostat. I check the motherboard and saw no burned points. Cleaned out the lent from the hose and inside the dryer. I am at that point where I need a professional to take a look.
Do I need to remove the gas line connecting to the dryer?
Viendo este video,pude arreglar mi secadora de gas.El problema fue coil kid.than You very much.
How does the timer factor into the dryer not getting heat? My timer still completes the timed cycle but I am seeing "infinity" across the red and black terminals of the timer. Confused.
I have a whirlpool gas dryer and what it does is not stay heating long enough to dry. It will run, it will glow an start to heat for about 15 to 20 sec then it stops heating. Wait about a minute an ahalf starts heating again for a few more sec then back off. That's all it will do. Close don't get dry. On off on off the whole cycle
Thank you.
Almost exactly the same problem here. Did you solve it and if so, how? Thanks!
My dryer will start running, igniter will glow, gas valve opens an starts heating for about 15sec then go out. After 1 1/2 min starts back up for 12 to 15 sec an out it. Same thing over an over. Thank you.
What does the flame sensor do exactly?
Muy buen video, consejos muy útiles. Saludos!!
Excellent video.
Do you have a video on how to remove/replace the coil? My dryer is a whirlpool model # WGD5790VQ0
I have a kenmore 70 series Gas dryer. My coils multimeter check parameters fall with your stated specs. But, I get the same results. Igniter glows red, solenoids click, gas blows, burner fires up but only runs for about 5 minutes then shuts off but never fires back on. 🤷♀️ Thus, do I or do I not have a solenoid coil problem? If not, what is causing the burner flame to prematurely extinguish?
A year later ... since nobody answered, I'll give it a shot. From what I understand, you do have (or did have) a coil problem. As the coils start to get weak, they can still open the gas valve when they are completely cool, but not when they're hot (or even warm). Thus when you first start the machine, it appears to work normally, but then the coils start to warm up, from electrical current and/or being close to a gas flame, and can't hold the valve open anymore, and the gas shuts off. Try it again an hour later and it'll work again... for a minute.
@@DaddyBeanDaddyBean Thanks for delayed reply. I went ahead and swapped out the coils despite the multimeter issue. Problem fixed a year ago.
@@carmelom269 I replaced mine tonight. Like yours, the old ones tested perfectly on the bench, but one of them failed - infinite resistance - after warming it up for literally five seconds with a hair dryer. Glad you got yours fixed too.
@@DaddyBeanDaddyBean “Penny saved is a Penny earned.” - Ben Franklin 🔔
Also check that your gas line wasnt crushed like mine was
I checked everything on this video but still no glow. Now what?
Love robot voice
I refuse to watch any video, that uses a bad computer voice.
Thank you very much for this video !!! It is very helpful. God bless .
May God Bless you too
Hi: Do I need to test the Solenoid terminal 2 and 3 together? Both of my Solenoid (new and old) stay at 1, or they both bad? Thank you
thanks very much I save a lot of money with this video.
Thanks for watching my videos. You can help me grow this channel by passing my channel address to family and friends.
czcams.com/channels/eO4F41uVUYsfMRW42D8f0g.html?view_as=subscriber
Angel theapplianceman
my problem with a Kenmore Model 90 Plus Series gas dryer seems completely random and makes me suspect the control board. The start relay was replaced. The dryer stops randomly after a few seconds or minutes in timed drying or moisture-sensing. Set it to 80 minutes it might stop (not always) after 10 minutes or complete the cycle. It always seems to be hot like it should be - it just shuts off! Any advice, please.
I need to model number to be able to see what you have
@@theapplianceman my model number is Model 90 Plus Series
110.78972891 78972
@@gerrygorecki6547 That is a 27 inch WP gas dryer here are the links to all my videos on 27 inch dryers. It is hard to diagnose something like that. The belt switch will stop the dryer motor if is deactivated or faulty, I wish I could tell what it is but is had without been there to see it work
czcams.com/users/my_videos?o=U&sq=27+inch
czcams.com/users/my_videos?o=U&sq=27+inch&pi=2
angel
@@theapplianceman - I know only too well how difficult it is to diagnose. I have a question - if the dryer is in Timer Mode, does the Moisture Sensor still have anything to do with the cycle? Can I then rule out the Moisture Sensor in Timer Mode? Thanks for your help.
@@theapplianceman If I click on either link - it takes me to a "studio", but shows "no content available". Will you kindly double check the links, please?
the video says the reading on the meter should be between .05-.15 ohms for the ignitor with meter set at 2k ohms. my ignitor reads .44 which is out of this scale. but the video says either .05-.15 for good and if it reads infinity its bad. what does it mean if the reading is .44?
That is good
I check everything would s timer make gas not to come on
All I have is what I describe on the video.
Good computer voice
Thank You For Watching My Videos
Click on the link below to check my website
www.do-it-yourself-washing-machine-and-dryer-repair-help.com/
Angel theapplianceman
Thank You For Watching My Videos
Click on the link below to check my website
www.do-it-yourself-washing-machine-and-dryer-repair-help.com/
Angel theapplianceman
My dryer stopped working so I told it your going the dump recycle scrap yard .....LOL was just kidding.. the next day trying it again and it worked... W T H. LOL
It could be that the motor overheated and the next day was already cool and maybe that is why it work. Or you scare the hell of it when you said it was going to the junk yard.
@@theapplianceman Yes, I wish cars would fix themself like that also.... LOL🖒🇺🇸
Video Marker for manafacturer telling you to replace parts in set. czcams.com/video/P9EY0iLb-9M/video.html