TIG THIN - heavy hertz (16ga Aluminum Welding)
Vložit
- čas přidán 11. 10. 2020
- 16ga Aluminum tubing butt joint weld. I kept the notes high, and the editing cuts to a minimum to demonstrate everything happening. I hope this helps bring a small bit of clarity about AC Frequency.
#ilovewelding #kanekidwelds #weldingisAWSome - Jak na to + styl
Awesome details! If anyone learns any of these tips on their own, you know how valuable the information is. Dialling in a setup for aluminum , if learning it all on your own, takes a lot of time!
Awesome Rush, just got done running some 16ga aluminum butt joints yesterday, love your enthusiastic and informative explanations you put at bottom of screen, stay the tig pioneer that you are ,brother!
Awesome, I like the subtitles. I have to pause and screen shot regularly but an information dense 5 mins is 👌 and the table tennis analogy made sense, but I’ll have to try it understand it better. Thanks for sharing 👊
Look up Skin Effect for induction heating ,that is what is changed with frequency changes
Excellent as always Rush. It's amazing how dead steady your hands are when your doing work. Thanks for sharing.
Beautiful work as usual, Rush. Could watch this all day. In fact I did that one day when I was laid up watching your vids🤣🤣👍🏻👍🏻👍🏻
Awesome! Thank you!
Thanks for the lesson!
It must be verrrry subtle..looks like your torch angle never changes. Almost like there’s no torch rotation as you advance. Love your welds and the little nuggets that help me progress bit by bit.
Cool videos man. I hope your work is cool with you doing the videos. Helps me a ton when I weld.
Thanks 👍
Your a master of the craft 🙌 love your videos post more lol
Dan Dreher thanks so much!
If I were trying to weld that aluminum, it would end up looking like swiss cheese. I can't even start the arc without blow through on 1/16" aluminum. And I've tried ever possible setting I could think of too... Thumbs Up!
I'm curious what wave form and balance you use and at what amperage? Your welds look incredible!
Thx for the explication about frequency ! Great job as usual.
As always, great vid. Where did you acquire the DCT products? Direct from the company? I found their website but there's nothing there about where to buy.
I don't know if its true or not, but I feel like the higher frequency also makes for a cleaner weld.
Awesome videos. What gloves do you use? Sometimes I see your gloves have extra protection on your index fingers in your videos and I've been looking for gloves just like that.
Curious as to if u can lay down the same quality dimes minus the foot pedal and with a thumbroll switch???
Стильно так, перчатки интересные👍
@kanekid are you using 1/16 tungsten?
Man I wish I could weld like that .. the only thing I get is buggers n holes.. lol I like the was u use ur fingers to dab ur filler .. ima beginner with a primeweld ( just purchased 2 days ago n I’m struggling. ) already went through 2 bottles n a bunch of scrap tube . Just gonna keep playing with the settings . Hardest part for me is getting that puddle started . Every time I add filler it stems to crusty buggers..
Nice work man 👍
Seems everyone Loves to either Weld Aluminium or learn how to Weld Aluminium.
The worst part of Welding Aluminium is having somewhere to rest your hand.
Where it won't get hotter than part your Welding 🥵
When will there be the Welding Olympics?? lol
What's the best way to get rid of the white, several ways I have tried. High grit polish buffing wheel, the best so far. But still rounds of the edges of weld. Seen a machine that took the black off stainless, from wire welding. Of course sand blast with fine medium. Try to dial the white out. Can't always do that. Just seeing other ways to get rid of the white oxidation. Awsome vid as always. I'm good at finish work. Making something look like it has never been welded. Time consuming to do all that to remove the white oxide layer. red scotch bright with the grain.
White = cathodic etching. Smaller cup size , tighter arc would be my guess.
@@richardj163 yea I know. It's almost impossible to not have on some welds. Like that polished pipe.
The etched zone will fade away in some days after welding, except in particular conditions...
That gas lens leaves a super wide cleaning line. I wonder if with a standard cup you could back off frequency a bit and maintain the same stability?
Skeetmgeett for a 1/4” wide bead, its not as much as it looks. The cup opening is still a size 5, so the insulated pathway for the EP to flow to is the same. The EP/EN balance & tungsten stickout, & tungsten point angle have much more control on etching.
(40-50° narrow bead & etch with deep penetration / 20-35° wider flat face bead, more etch, less penetration)
I switched to always running a Ck gas lens for both AC & DC about 5 years ago. I’ve had much more arc stability and control on AC ever since the switch, especially with mixed gasses.
@@KANEKIDWELDS interesting. Every time I try a gas lens on ac, it sounds super angry. Do you think the large bottle neck from lens to 5/16 acts differently than the straight shot of a standard? Not trash talking, strictly nerding out.
I’ve only had those issues with cheaper gas lenses. Check to see if yours has a large zinc retainer, or a small brass or copper one holding the screens. I’ve blown out nearly every zinc retainer lens I’ve used...
Are you running a transformer or inverter machine? That could be a big factor as well.
@@KANEKIDWELDS it's a dynasty 200 watercooled #20, Consumables were quality. Whatever you're doing is working really well. Love the video.
Muito bom
These bad boys getting anodized when you're done?
0:55 Skin effect where the the electrons travel in a thin surface of the material. The higher the frequency the shallower the penetration of the electricity( the core of the conductors carries no electricity curent from 60htz and higher frequencies) this applies to your table tennis analogy
Thank you for the continued explanation!
Thank you it's just connecting the dots to my induction heating research
The higher the frequency the narrower the arc. But that has nothing to do with penetration so don’t try to talk out of your ass
@@wiley0714 mechanix has a nice box cutter glove to help yourself out safely.
Amperage?
Seems like way too much torch angle but I guess I have a lot to learn
Please try that on 18gauge without inverter machine.
I used to weld aluminum sheet metal on a syncrowave 351 transformer daily. I spent 12 years with that machine & have zero reason to digress and waste the extra money on power.
Buy a positioner
.
This isn't thin at all
OK hero.
20 gauge is thin
@@GEEZUZ22 OK hero. Where's YOUR video? Ohh....yeah.....you don't have one. You're a keyboard welder.
You clearly can't weld with a keyboard lol