Laminate is Super Easy! || Get the Best Workbench Surface
Vložit
- čas přidán 10. 09. 2024
- Bourbon Bite Short of: How to Install Laminate
Merchandise & Plans: www.bourbonmot...
Patreon Page: / bourbonmothwoodworking
Cameo: www.cameo.com/b...
Instagram: / bourbonmoth
Links below to tools and supplies:
3M Cubitron Sandpaper: lddy.no/1hset
Contact Cement: amzn.to/3q7odIt
Laminate Scorer: amzn.to/3ENgDql
Laminate Roller: amzn.to/3q9A48K
Laminate: amzn.to/3EMTEvJ
Foam Roller: amzn.to/3F9QEcR
CA Glue: amzn.to/3Ht7eqr
16 Gauge Nailer: amzn.to/30kikNI
Eye Protection: amzn.to/3gIO4A5
Woodpeckers square: amzn.to/3q8XObc
Drill & Driver https: amzn.to/35zBfmz
ISOtunes Bluetooth Hearing Protection (10% off code- BOURBONMOTH10) bit.ly/Bourbon...
Bits & Bits Precision Cutting Tools (10% off code- BOURBONBITS)
bitsbits.com/r...
RZ Mask (15% off code: BOURBONMOTH15)
www.awin1.com/c...
Total Boat Epoxy: www.totalboat....
Nicks Handmade Boots: bit.ly/3vZ8uMR
Firm Grip Work Gloves: thd.co/3LEO5TE
PowerPro Fasteners: amzn.to/3u3Mgtj
Pony Jorgensen Clamps: bit.ly/3knr9fZ
Spec Ops Hammer: amzn.to/3fMjAOd
Spec Ops Tape Measure: amzn.to/3w1M788
Spec Ops Pry Bar: amzn.to/2Ro3iC2
Spec Ops Chisels: amzn.to/3ga8kKv
Spec Ops Screw Drivers: amzn.to/3ciV8ls
Spec ops utility Knife: amzn.to/3g5ysWZ
Grizzly Tools:
Table Saw: amzn.to/3q8Wbu6
Jointer: amzn.to/3gFHE6a
Planer: amzn.to/3xCzH7r
Dust Collector: amzn.to/35AFEWw
Air Filtration: amzn.to/3zyXXsK
Band Saw: amzn.to/3gEtCAm
Drill Press: amzn.to/3xvhxEh
Lathe: amzn.to/3vChWUb
When I can afford to buy plywood again I'm definitely going to do this to my workbenches.
When I redo my project table, I might go this route..
1:10 I have a rolling infeed table (SO handy for feeding long or wide stick through the table saw) which doubles as a parts cabinet and tool crib. Along with my project table, I did poplar banding around it, knocked the corners down with a 45 degree angle cut with my circular saw, and then added a chamfer all the way around. So when I inevitably bash myself against one of those surfaces, there's less cussing.
Laminate is like the past. In the Northeastern PA, it's hard to get. Great video
Free delivery from Lowe's in a few days...
I always enjoy The Bites.
Great video, I've used your method multiple times now and can say that it really as easy to do as it looks. thanks for another great video
I can't wait to get a Harbor Freight table saw.
Great video😅
And, looks like a small chamfer router bit to finish it off? Nice video!
can you rout grooves for track clamps? i assume so, but just checking if it would be an issue looks great by the way!
thanks
That's the stuff that's on my kitchen countertops!
I hate it because BLACK shows every grain of dust and dirt, or any drops from spills.
But I would not mind it on my workbench.
hey, hey, hey. at 1:23 what is the magic we are NOT seeing ? I have this huge sheet and NO idea how to cut it, looks like you clamp it down and score it and then bend it till it POPS ??
Remember to j roll all outside edges so you get that nice bubble top ;)
You are very brave, I would have cut it bigger. I have better luck with the solvent based contact adhesive. Sticks better for me. Just made wings for my table saw. In addition to rolling it I clamped the edges for several days just to be sure it did not delaminate. If you stick the stuff in the wrong position you can remove it with lacquer thinner if you use solvent based adhesive. If is comes off cleanly you can restick it with the same glue.
Nice video. You never wear a mask when making cuts. Is your filtration good enough? I find I have to wear a mask or it wrecks my allergies
Do you have plans for that rolling cart? It's awesome
Where do you source your laminate? Trying to figure out where is best to buy and what thickness/etc
I order from a big box store, a 4 by 8 sheet, and a big box shows up ! I bought a maple peice and a cherry ... HD also sells you samples or gives them to you. Good luck !
Nothing to do with laminate- sorry- but the music in your videos is really good and unusual- can you post a play list by any chance?