i unplug the connector of the icv but still the idle/acceleration is very low.yours still have power .possible my problem of my 190e sir? the icv or the potentiometer?
Hello if all original and has not been touched not the ICV then the speed should increase in the event of capture ICV is manually adjusted was the hex screw. Usually rpm is not good if there is leakage of air or if the potentiometer is damaged
My 190e has starting trouble,when cold start there is no problem,but when the engine run for 10 or more after off the engine,at the same time we start it will ok but we off the engine for 10 min it will not start,then we want to start the engine minimum 3or 4 times to crank the engine, please tell me why it happened
Test your fuel accumulator czcams.com/video/Ua5nyUGXC0Y/video.html 30:30 if it leaking you found the problem. Old accumulator is common isues on old mercedes if diafragm is broken only fix is to get new or use in good condition.
Idle is too high check for vacuum leaks on rubber boot and pipes, air flow potentiometer when engine is cold idle go to 1000 rpm when engine is warm then drop of basic 750 rpm when ac is on idle go up.
@@MarTengYT it should be 650-750 rpm when the engine is idling and 800-850 when the air conditioner is on. Because then there is a greater load on the engine and it has to compensate with higher revolutions
@@190mex thanks a lot. I would check the vacuum leaks or rubber boot and pipes. I just adjust the timing distributor and the idle in the throttle body to get that 900rpm coz when i turn on the ac the engine shut off.
That's just the beginning of the removal. :) Then what ? Can you just pull out on that rubber support that ICV it stays into? I can't see what's under that rubber harness/support thing, so i hesitate about just pulling it out. Thanks.
En mi caso el coche arranca perfecto en frío, pero en caliente tan pronto suben las rpm caen hasta 500 o así, todo el coche vibra y parece que se vaya a calar, tarda unos segundos en estabilizarse después... Por qué puede ser?
@@190mex Thank you very much, my temperature sensor placed in the front of the engine has 4 pins. It seems to he in a good shape (not tested yet) how could I do that? How can I test flow sensor? The car's plenty of power it only fails when ignition.
Black smoke, gasoline consumption, engine swing, and the Angkshin indicator, which is reduced to five, and climbs up to ten, and most of the time, the car turns on its own while it is parked or while driving. ترجمة Google translate.google.com › translate تترجم خدمة Google المجانية الكلمات والعبارات وصفحات الويب بين الانجليزية وأكثر من 100 لغة أخرى. قاموس
I just subscribed, ur videos are great. Keep up the good work.
Hi, nice sound, did you modify the exhaust?
Thank you
Thank youu!
may i ask where to put the voltmeter for the pos + neg needle to test
www.landiss.com/mixture.htm
i unplug the connector of the icv but still the idle/acceleration is very low.yours still have power .possible my problem of my 190e sir? the icv or the potentiometer?
Check whether the potentiometer in the factory settings or is damaged too much and gives the wrong parameters
How do you take that ICV out so you can clean it?
You unfortunately the clamps around the tubes that connect to it from the top and bottom and take it out to clean it out I have no clue
my car doesn't change in rpm at all when i removed the connector? I already have a new OVP so what is the reason
Hello if all original and has not been touched not the ICV then the speed should increase in the event of capture ICV is manually adjusted was the hex screw. Usually rpm is not good if there is leakage of air or if the potentiometer is damaged
My 190e has starting trouble,when cold start there is no problem,but when the engine run for 10 or more after off the engine,at the same time we start it will ok but we off the engine for 10 min it will not start,then we want to start the engine minimum 3or 4 times to crank the engine, please tell me why it happened
Test your fuel accumulator czcams.com/video/Ua5nyUGXC0Y/video.html 30:30 if it leaking you found the problem. Old accumulator is common isues on old mercedes if diafragm is broken only fix is to get new or use in good condition.
I just want to ask. Is it ok to have 1000rpm when idling and when the A.C is on its about 800rpm.?
Idle is too high check for vacuum leaks on rubber boot and pipes, air flow potentiometer when engine is cold idle go to 1000 rpm when engine is warm then drop of basic 750 rpm when ac is on idle go up.
@@190mex how about 900rpm when idling? And when the A.C is on its about 750-800 rpm.
@@MarTengYT it should be 650-750 rpm when the engine is idling and 800-850 when the air conditioner is on. Because then there is a greater load on the engine and it has to compensate with higher revolutions
@@190mex thanks a lot. I would check the vacuum leaks or rubber boot and pipes. I just adjust the timing distributor and the idle in the throttle body to get that 900rpm coz when i turn on the ac the engine shut off.
@The Gaming Mechanic If you have KE-Jetronic system of injection you cannot adjust timing manually.
thnks...
what is expected rpm at start up?
Cold start 1100 rpm warm 750-800 rpm
thx! do you know why mine is always at 500? whether hot or cold? I might try cleaning out the ICV
Clean ICV and test air flow potentiometar on idle most be 0.7 +- 0.1 V
Por que no hablas!!!???
У меня 190 мерседес к нему подходит другой движок Который нет дозатора кто знает подскажите
Om 605 engine
Unplug the connector and remove rubber house. Cleaning with carburetor cleaner inside.
That's just the beginning of the removal. :) Then what ? Can you just pull out on that rubber support that ICV it stays into? I can't see what's under that rubber harness/support thing, so i hesitate about just pulling it out. Thanks.
If your not going to explain what you are doing, I turn this off. No good.
En mi caso el coche arranca perfecto en frío, pero en caliente tan pronto suben las rpm caen hasta 500 o así, todo el coche vibra y parece que se vaya a calar, tarda unos segundos en estabilizarse después... Por qué puede ser?
test fuel pressure, test air flow sensor, test temperature sensor( for ECU )4pin or 2 pin
@@190mex Thank you very much, my temperature sensor placed in the front of the engine has 4 pins. It seems to he in a good shape (not tested yet) how could I do that? How can I test flow sensor? The car's plenty of power it only fails when ignition.
@@190mex my 190e start well and have good idle at hot, but at cold is too low 500rpm and die
@@adrianogatti7328 check for vacuum leaks on rubber boot and pipes
@@adrianogatti7328 cis-jetronic.com/public_doc/CIStroubleshooting.jpg
Black smoke, gasoline consumption, engine swing, and the Angkshin indicator, which is reduced to five, and climbs up to ten, and most of the time, the car turns on its own while it is parked or while driving.
ترجمة Google
translate.google.com › translate
تترجم خدمة Google المجانية الكلمات والعبارات وصفحات الويب بين الانجليزية وأكثر من 100 لغة أخرى.
قاموس
In most cases there is a ke jetronic air flow potentiometer or vacuum leak !