How to Replace Front CV Axle Shaft 2009-2015 Honda Pilot
Vložit
- čas přidán 11. 09. 2024
- Buy Now!
New CV Axle Assembly from 1AAuto.com 1aau.to/ia/1AAC...
This video shows you how to install a new Front CV Axle Shaft in your 2009-2015 Honda Pilot. A CV axle has flexible joints. Often, these joints wear out, or seize from contaminants due to the protective boot tearing open. A worn joint is prone to breakage, or other hazards. If your vehicle needs a new CV axle, install a quality TRQ axle that is engineered to your vehicle’s specifications.
This process should be similar on the following vehicles:
2009 Honda Pilot
2010 Honda Pilot
2011 Honda Pilot
2012 Honda Pilot
2013 Honda Pilot
2014 Honda Pilot
2015 Honda Pilot
Tools you will need:
• Flat Blade Screwdriver 1aau.to/tbdS/1A...
• Phillips Head Screwdriver 1aau.to/tbdS/1A...
• Pry Bar 1aau.to/tGI/1AX...
• 10mm Wrench 1aau.to/tMN/1AX...
• 24mm Wrench
• 10mm Socket 1aau.to/taTU/1A...
• 17mm Socket 1aau.to/tbuP/1A...
• 19mm Socket 1aau.to/t8K/1AX...
• 22mm Socket 1aau.to/tgX/1AX...
• 24mm Socket
• 35mm Socket 1aau.to/t7/1AAS...
• Brake Caliper Hanger 1aau.to/tfS/1AX...
• 1/2 Inch Breaker Bar 1aau.to/tkj/1AX...
• Ratchet 1aau.to/ta2e/1A...
• Socket Driver
• Torque Wrench 1aau.to/tafV/1A...
• Anti-Seize Grease
• Brake Grease
• Brake Parts Cleaner
• Copper Anti-Seize
• Gloves 1aau.to/twT/1AX...
• Liquid Thread Locker
• Safety Glasses 1aau.to/trk/1AX...
• Sandpaper
• Hammer 1aau.to/tJB/1AX...
• Punch
• Wire Brush 1aau.to/toH/1AX...
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
Save yourselves a 2nd trip to the hardware store gentlemen it's a 36mm socket not freaking 35!
You make it look easy, Thank you for the video!
A great video, a step-by-step "how to" thanks
Why was the replacement needed? what was the symptom?
Great Video!!! Thanks!!!!
Torque spec for tie rod?
Change the title to “How to Replace the Driver-side/Left side Front CV Axle Shaft 2009-2015 Honda Pilot
No need to drain the trans fluid first?
The transmission fluid is muddy
Had front right CV joint assembly replaced with Napa NCV-940710, alignment done but now pulls left on highway from right lane (did not pull before repair). Same time replaced both front stabilizer bar links. Any ideas? If spindle nut put back on with air impact wrench instead of 242 ft./lbs torque wrench could this cause pulling to left? 160,000 miles on Honda... should I have just replaced both left and right CV joint since I didn't go back with Honda OEM?
There is a mistake on the size of the axle socket that made me return to the store to get the correct socket size. Is not 15 mm. The correct size is 16 mm
RH side is coming diiferent it is long one not short like this one !!
I don't have half of the tools he's working with.