4Runner LED Rear Blinkers and Backup Lights
Vložit
- čas přidán 21. 08. 2024
- In this video I install a set of LASFIT LED rear blinker and backup lights on my 5th generation Toyota 4Runner (2016-2020). Here's a side by side comparison with stock bulbs and full install instructions.
Switchback Blinkers:
amzn.to/2MZXBoo
Low Beams:
Low Beam Bulbs: amzn.to/375ZvgT
Fog Lights:
amzn.to/3zOlHZ0
Backup Lights:
amzn.to/2RYwZ8O
#Toyota #Toyota4Runner #4Runner #LASFIT #ytmikec - Auta a dopravní prostředky
I just did this exact swap on my 2019. There is absolutely no need to take the entire housing off. It’s very easy to do with it still installed.
I was gona say the same,. No need for removal.
Do you have the link to the rear singals?
Some people have posted that they didn’t have to remove the entire light assembly, which is possible if you’re replacement bulb isn’t too big/long. I went with the LasFit 7440NA bulbs which required me remove the light assembly. There was not enough slack in the wire harness on my 2018 SR5 once you put in the LasFit bulbs to make the turn back into the light assembly. Once removed, it’s a straight shot in. Especially if you install the bulb and it doesn’t work and you have to flip the bulb. Light assembly is finicky to get out with a couple of light palm slaps and reward pressure, but with a little patience it comes out as described in his video. Goes back in with no issues. Thanks for the video! Nice and helpful!
You can change the bulb without taking the light of the vehicle. Just remove the panel and reach in.
I was thinking the same thing.
Thank you for all of the great content that you are pushing out for us all! I’m a new 4Runner owner and am loving all of the fun mods that are available and I’ve learned a ton from your videos.
both light bulbs can replace without remove whole assemply
I did mine in a 21’ limited and if you pull a little slack you can swap them without removing the light
All your videos are awesome. Thank you so much. They are definitely appreciated. 🙏🤘
Don't need to remove light unit to replace reverse light on 2021 4runner. 10 minute job....I did it.
Is it me or is it that the rear led blinkers and out of sequence? its seems like tis flashing fast and slow at random times.
Swapped my entire housing for a different taillight. Was a pain in the butt trying to get my driver side off. Prob 10-15 minutes just working it off. Surprised I didn't break it
Do you have a recommendation for LED daytime running lights that don’t flicker or shake?
A lot of people on Amazon are saying these overheat in warm weather and start hyper-flashing after blinking for 30-60 sec. Has that happened to you?
I haven't had any issues since install but our whether isn't super hot so perhaps its more of an issue in southern climates?
My LH hyper flashes
My dad has an 20019 Toyota 4runner that has been doing weird things like thr back blinker lights have started flashing and no one is inside the truck I'd managed to get an video of it help
Great video👏🏼👏🏼
i installed these Lastfit led lights on my 2019 4Runner but it does not work for the turn signals, only works for hazards. Tried switching 180 and opposite side but no luck. Front turns work fine, any suggestions????
Thanks for the video. Did you change your interior bulbs, if so what bulbs did you use?
What did you use for your license plate bulbs?
Do you need to remove the whole housing to just replace the turn signal bulbs??? look liek you can just reach up and twist it out, no ?
Just changed them myself without removal of housing
Purchased these for a 2018 Toyota 4Runner. They did not work, they hyper flashed. Got no help from Lasfit
The bulbs could NOT be replaced with the light assembly mounted ?
It really needs to be removed, it looks accessible ?
Correct, you will have to remove the assembly to replace the bulbs. If it were possible to do without removing I would have!
@@DrivenCompanion that is wrong. You just added an extra unnecessary step. Why did you take the assembly off instead of just unplugging the lights?
So I installed these in my ‘18, and the hazards work fine, but the turn signals hyperflash. Was told by Lasfit running front and rears can be problematic. Was thinking of returning these, but also read something about an updated LED relay?
Sorry to hear that. I run front and rear with no hyperflash
Don’t use hazards just use either right or left they will hyper
Do they make amber headlights? Would be perfect for people who drive desert and city.
Pretty sure amber headlights are illegal.
You can just replace the light bulb with LED without removing the whole tail light right?
No, fixture needs to be removed to replace the bulb
@@DrivenCompanion I replaced mine with LED today, didn't need to take out the whole light. Just open the cover, swap out the bulb and that's it!
@@blackfw190D YEAH, you can replace the bulbs with out removing the the whole brake light. You got to tug on the wire a little to get enough slack to fit the bulb in.
How come the link to the tear backup light on Amazon says it doesnt fit my 2020 4runner? I have a trd off road premium trim .
Not 100% sure but I think these will still work on your 2020.
@@DrivenCompanion thanks. I just bought a new trd off road premium two days ago. Love it. So planted on the road transmission isnt searching for a gear.
I upgraded from a 2015 rav4.
Do you have the part number for the rear turn signals? or link?
Links are in the descriptions. Here is the link for the turn signals: amzn.to/3106SCH
Are the actual break light bulbs replaceable
Not certain what you mean by that.. The bulbs insert into the fixture so yes they are replaceable.
@@DrivenCompanion He's asking if the brake lights are replaceable. No, they're not.
No hyper flash?
Nope
They actually do after a min or two. The problem with these build in resister LED builds is that they get hot. LASfit calls it a protection feature.
Having a hard time getting my housing off.
I assume you mean the fixture. Just keep working it straight back with no twisting and don't be afraid to pull hard. You could try hitting the side of the fixture before pulling to lossen it up. It is a little tricky but you'll get it!
I fell sorry for the person behind you when you turn on that blinker, Especially at night,, Thats hearting my eyes just trying to watch it on video.. I had to stop the video,, Why do thank you need your blinker that intense,, Turn off your garage light and set behind it for 2 minints and see if its not bothering your eyes,,
It’s gonna look much brighter in a camera.
Plus when you want to turn they actually let you pass but with the oem bulbs they won't let you pass
Fell??
Yep, blind others for the sake of themselves, sounds about right