How to fix your GPS when it isn't working (INAV)
Vložit
- čas přidán 17. 05. 2024
- INAV Quad Build Video: • INAV 7 Quad Setup: ful...
INAV Wing Build Series: • INAV for Beginners 202...
Thank you for taking the time to watch the video. You can find me on social media at
• / painless360
• / painless360
• www.thingiverse.com/painless360
You can help support the channel by simply liking the video and subscribing to the channel. It helps a lot! In addition you can use these links to support the time I spend helping others:
• / painless360
• paypal.me/painless360.
Remember that reviews are subjective. Don't rely on one person’s opinion - watch multiple 'reviews' and make your own mind up. Unlike some, I don't do this to replace a day job as that makes the creative decisions all about 'getting paid'. I am free to be completely honest and clear in the videos I make. I’m not asking vendors to pay for these videos, so opinions are mine alone.
Please also keep in mind that the comment section is not a forum: any comments that are rude, disrespectful or use bullying or threatening language will be deleted. Pedantry isn't encouraged either. This channel is all about helping others and passing on advice and ideas, so please comment in that spirit. Comments that don't adhere to these simple rules will be deleted.
Thanks again for watching! Remember to use the playlists as I collect videos into subjects to help you learn about a topic and find related information.
Please LIKE and SUBSCRIBE and above all - Happy Flying!
#INAV #GPS #Setup
0:33 It's like the two props are attached to each other...
RC magic!!
Fantastic tips, Lee! Thanks a bunch! 😃
Very helpful!
Stay safe there with your family! 🖖😊
My biggest issue with GPSs mounted like that is not the GPS itself but the magnetometer. I have been moving the GPS opposite to the battery cables to help with this issue. Another pet peeve of mine is that those small GPSs with magnetometers don't show where it should be pointing, you have to search for the information or look at the magnetometer chip itself to figure it out.
See my video on compass alignment. It isn't too tricky if you follow the process. Most of the popular GPS and Compass units have the default orientation now so work with the defaults... Happy flying
Thanks for the tips!
I have a question specifically for fixed wing foam planes and GPS. Do you think that foam is blocking the GPS signal or make it work sub optimally? That said, is it ok to put the GPS in the battery bay of a foam fixed wing plane?
Cheers!
I've mounted a GPS under thin layers of foam, tape and plastic and not noticed any loss of performance.. Happy flying!
Write the specs and wiring diagram on a small paper to foldup and bag with your parts you keep .parts like gps , buc converters voltage regulators , camera switches, rx , buzzers , vtx's
I have already seen GPS mounted upside down with the antenna facing the ground!😀
Not seen that here, yet. Hopefully, those following my builds on this channel are seeing how it is done.... Happy flying
I configured mine with gps and compass but since i heard in 7.1 you can use only gps, I unselected the compass and that took away the Nav modes.
How do I set the GPS only for nav modes
Covered in the release notes...
Currently, if you wish to fly a multirotor without a compass. You will need to enable a compass (fake is ok) to change navigational modes in Configurator. You should disable the compass after making the changes. This has been fixed for a future release.
Ive got a quad /gps that works fine in BF but when i converted it over to iNav it doesnt read the gps at all. I even loaded BF back on and it still works in BF but no go with iNav. Yes I have the uart set the same as BF and I do have GPS enabled in the Configuration tab. Any suggestions?
What GPS is it? Ask in inav discrod also
You don't mention the GPS type... INAV stopped supporting NMEA compass protocol recently so you'll have to check the one you have supports GNSS... Happy flying
@@Painless360 Thanks so much for responding. It is a brand new M10 GPS and compass. The compass is working without issue. i think it is foxeer.
While I have my quad connected to my computer It locks on the sats and shows on the map my location. Only problem I have ,No sats are showing in my DJI goggles It flashes a red sat ,but no sats like in betaflight. What is the reason this could be happening.
Cheers
Have you watched my dji setup videos? What troubleshooting have you already done?
@@Painless360 I have never come across anything like this I have everything I want in the goggles after the hack, there' is nothing I can think of why it'ss doing this I could understand if rx and tx were wired incorrectly but there not as I get all the sats locked in while on betaflight It's just not showing the sats in the goggles. That's why I asked if anything comes to mind?
It could be a few things, sats not locking when DJI unit is powered due to interference, font file issues on the goggles, something wrong in the setup in INAV... Best of luck